Search results for " Motor"
showing 10 items of 1044 documents
Sensorless low Range Speed Estimation and Parameter Identification of Induction Motor Drives Devoted to Lifts Automatic Rescue Devices
2010
In this paper a sensorless rotor speed estimation and parameter identification algorithm is presented. The algorithm is designed specifically for induction motor (IM) drives devoted to automatic rescue devices (ARD) used in lifts and hoist applications. Its peculiarity is that it is based on the sinusoidal steady state mathematical model of the IM and, therefore, can be implemented on a low cost micro-controller in a simple way, however without lacking in terms of dynamic performance. It is also capable of self tuning so that no information is required about the specific IM used in the ARD drive. Finally the algorithm allows also an appreciable energy saving of the ARD when compared to olde…
PVDF based vibration measurements and their correlation with torque estimation in a FOC induction motor drive
2008
This paper presents a study concerning the vibrations generated by an induction motor drive controlled by field oriented control algorithm (FOC). The aim of the study is to identify suitable measurement points and analysis techniques in order to achieve information about vibration generated by an electric drive. Vibrations take origin both by the torque generated by the motor and the motor supply through an inverter, then they are transmitted to neighbouring structures. Torque is estimated on the basis of the estimated flux linkage; vibrations have been both measured and analysed numerically by FEM at two points of the cradle. The numerical and experimental analysis have been carried out fo…
A study on the influence of permanent magnet dimensions and stator core structures on the torque of the disc-type brushless DC motor
2000
This paper presents a three-dimensional analysis of the magnetic field distribution for a disc-type, double-sided, permanent magnet, brushless dc motor with a toroidal stator core. Calculations are carried out using the OPERA (3D) package with the TOSCA module. The electromagnetic torque is determined from the Maxwell stress tensor. For comparison, various permanent magnet dimensions and slotless vs. quasi-slotted stator cores are analysed, with an iron powder-resin composite effectively used to imitate the slotted core. The torque ripple is shown to be effectively reduced by appropriate permanent magnet dimensions. The simulation results are in good agreement with experimental data obtaine…
Suitability of blends from virgin and reprocessed polylactide: performance and energy valorization kinetics
2018
[EN] A blending strategy of virgin and reprocessed polylactide may be postulated as an alternative to reduce the material cost at industrial level, and as a valorisation route to plastic waste management of production scraps. The performance of blends prepared from virgin polylactide and polylactide mechanically reprocessed up to two cycles (PLA-V/R) was assessed in terms of thermo-oxidative stability, morphology, viscoelasticity and thermal kinetics for energetic valorisation. PLA-V/R blends showed appropriate thermo-oxidative stability. The amorphous nature of polylactide was preserved after blending. The viscoelastic properties showed an increment of the mechanical blend effectiveness, w…
Parameter identification of induction motor model using genetic algorithms
1998
The paper deals with methods of identification of the parameters of an induction motor model using genetic algorithms. It is supposed that the inverter supplying the motor is directly accessible for control of the conduction sequences of its power switches. This makes it possible to carry out a test consisting of a transient from standstill to steady-state operation at a given frequency and successive free motion to standstill. During this test, data are acquired referring to stator voltages, and currents and speed. Then, a genetic algorithm is employed with the aim of determining the mechanical and electrical parameters of the model, so as to reproduce the input-output behaviour of a real …
Rotor-bar breakage mechanism and prognosis in an induction motor
2015
© 1982-2012 IEEE. This paper proposes a condition-based maintenance and prognostics and health management (CBM/PHM) procedure for a rotor bar in an induction motor. The methodology is based on the results of a fatigue test intended to reproduce in the most natural way a bar breakage in order to carry out a comparison between transient and stationary diagnosis methods for incipient fault detection. Newly developed techniques in stator-current transient analysis have allowed tracking the developing fault during the last part of the test, identifying the failure mechanism, and establishing a physical model of the process. This nonlinear failure model is integrated in a particle filtering algor…
The effect of manufacturing tolerances on a tubular linear ferrite motor
2015
This study presents a numerical and experimental study on the effect of permanent magnet tolerances on the performances of a Tubular Linear Ferrite Motor. The statistical distribution of the magnetic characteristic of a set of commercial magnets is obtained experimentally while the performances of a the tubular motor are numerically evaluated. The performances that have been considered are: cogging force, end effect force and generated thrust. It has been shown that: 1)the statistical variability of the magnets modifies the time behavior of the cogging force; 2)the value of both the end effect cogging force and the generated thrust are directly linked to the values of then remanence field o…
Vibration signature analysis for monitoring rotor broken bar in double squirrel cage induction motors based on wavelet analysis
2014
Purpose – The purpose of this paper is to present a diagnosis technique, for rotor broken bar in double cage induction motor, based on advanced use of wavelet transform analysis. The proposed technique is experimentally validated. Design/methodology/approach – The proposed approach is based on a combined use of frequency sliding and wavelet transform analysis, to isolate the contribution of the rotor fault components issued from vibration signals in a single frequency band. Findings – The proposed technique is reliable for tracking the rotor fault components over time-frequency domain. The quantitative analysis results based on this technique are the proof of its robustness. Research limit…
CO2LD: An innovation educational project for High Degree Professional Training in Refrigeration
2013
EN] Refrigeration is one of the technology sectors that has sufered the most changes in the last twenty years, because of the negative impact of the fuids used in the refrigeration cycles, i.e., refrigerants, due to their impact on the ozone layer and their contribution to global warming. As a result of their negative efects, the European Union has established several directives to restrict the use of refrigerant fuids, and the sector therefore needs to adapt to the new regulations. This process of adaptation of the refrigeration sector to the new regulations must be carried out by all the agents involved, including those engaged in the training and education of the future refrigeration tec…
A methodology to assess the energetic valorization of bio-based polymers from the packaging industry: pyrolysis of reprocessed polylactide
2012
The energetic valorization process of bio-based polymers is addressed in this study, taking polylactide (PLA) as model. The pyrolysis of virgin and multiple-injected PLA was simulated by means of multi-rate linear-non-isothermal thermogravimetric experiments. A complete methodology, involving control of gases, thermal stability and thermal decomposition kinetics was proposed. The release of gases was monitored by Evolved Gas Analysis of the fumes of pyrolysis, by in-line FT-IR, with the aid of 2D-correlation IR characterization. A novel model to establish the thermal stability of PLAs under any linear heating profile was proposed. A kinetic strategy was methodically applied to assess the th…