Search results for " Torque"

Identification and Experimental Validation of an Induction Motor Thermal Model for Improved Drivetrain Design

2017

The ability of an electric powertrain to perform according to mechanical specifications is equally important as assessing its thermal protection limits, which are affected by its electrical and thermal properties. Although rated parameters (such as power, torque, etc.) are easily accessible in catalogs of equipment producers, more specific properties like mass/length of copper winding, heat dissipation factor, etc., are not available to customers. Therefore, an effective selection of drivetrain components is limited due to the lack of sufficient data and the need to consult critical design decisions with suppliers. To overcome this limitation, we propose a method to estimate the temperature…

Cogging torque comparison of Interior Permanent Magnet Synchronous Generators with different stator windings

2017

This paper presents the comparison between the cogging torques produced by four IPMSGs (Interior Permanent Magnet Synchronous Generators) with different stator winding configurations. More in detail, an IPMSG model, which is derived from a commercial geometry, is analyzed through means of a FEM (Finite Element Method) approach. Then, three more structures are determined and analyzed by adequately changing the number of stator slots of the basic IPMSG stator structure and by maintaining the same rotor configuration. From the obtained simulation results, the cogging torque components for each structure are determined and compared. From this comparison, it can be stated that the use of dissymm…

Field‐circuit analysis of construction modifications of a torus‐type PMDC motor

2003

This paper presents the field‐circuit analysis of a disc‐type torus DC motor with permanent magnets. Calculations of the magnetic field are carried out using the finite element method (FEM) in the 3D space. The integral quantities like the ripple‐cogging torque, back electromotive force, flux linkage, self and mutual inductances of the winding are analyzed. The electromagnetic torque is comparatively determined from the Maxwell stress tensor and co‐energy methods. Based on the 3D magnetic field calculations, the lumped‐parameter model of the tested motor is constructed, taking into account an electronic power converter as well. For comparison, various permanent magnet widths and teeth thick…

Finite-element performance comparison of IPMSMs with unsymmetrical double-layer windings

2017

This paper presents a comparison of the performances between IPMSMs (Interior Permanent Magnet Synchronous Machine) with a symmetrical and with two different types of unsymmetrical windings. The aim is to demonstrate that the adoption of slightly unsymmetrical windings does not significantly affect the performances of the machines, both in terms of cogging torque and torque/load angle characteristics, providing also the advantage of a higher possibility of choice in terms of slot number/poles ratio. More in particular, an IPMSM model (named IPMSM-1) derived from a commercial geometry equipped with a symmetrical winding is analyzed by using a Finite Element Method (FEM) approach. The simulat…

On the use of a powder rheometer to characterize the powder flowability at low consolidation with torque resistances

2017

The Anton Paar Powder Cell was used to measure the torque necessary to rotate an impeller in beds of glass beads, sand and alumina powders aerated between no aeration to the minimum for fluidization. Measured torque values depend on the material tested, on the air flow rate applied, on the impeller depth and on the height of the impeller blade. The effect of the impeller depth is linear for low impeller depth and is less than linear at high depth values. A model was developed for the interpretation of the experimental results based on the idea that the material is shearing on the surface described by the impeller rotation. The model allows to estimate an effectiveness of the impeller in the…

Spin Pumping and Torque Statistics in the Quantum Noise Limit

2016

We analyze the statistics of charge and energy currents and spin torque in a metallic nanomagnet coupled to a large magnetic metal via a tunnel contact. We derive a Keldysh action for the tunnel barrier, describing the stochastic currents in the presence of a magnetization precessing with the rate $\Omega$. In contrast to some earlier approaches, we include the geometric phases that affect the counting statistics. We illustrate the use of the action by deriving spintronic fluctuation relations, the quantum limit of pumped current noise, and consider the fluctuations in two specific cases: the situation with a stable precession of magnetization driven by spin transfer torque, and the torque-…

Current signature based fault diagnosis of field-oriented and direct torque-controlled induction motor drives

2017

In this article, the operation of three-phase squirrel-cage induction motors is analysed under faulty conditions in closed loop with state-of-the-art controllers, namely, the field-oriented control...

On damping characteristics of frictional hysteresis in pre-sliding range

2016

Frictional hysteresis at relative motion in the pre-sliding range is considered. This effect is characterized by an elasto-plastic interaction, and that on the micro-scale, between two rubbing surfaces in contact that gives rise to nonlinear friction force. The pre-sliding friction force yields hysteresis in displacement. In this study, the damping characteristics of frictional hysteresis are analyzed. It is worth noting that we exclude the viscous damping mechanisms and focus on the pure hysteresis damping to be accounted in the friction modeling. The general properties of pre-sliding friction hysteresis are demonstrated and then compared with the limit case of discontinuous Coulomb fricti…

Time course of central and peripheral fatigue differs when maintaining a constant-EMG task vs. a constant-torque task

2005

Skyrmion-number dependence of spin-transfer torque on magnetic bubbles

2015

We theoretically study the skyrmion-number dependence of spin-transfer torque acting on magnetic bubbles. The skymrion number of magnetic bubbles can take any integer value depending on the magnetic profile on its circumference and the size of the bubble. We find that the transverse motion of a bubble with respect to the charge current is greatly suppressed as the absolute value of the skyrmion number departs from unity, whereas the longitudinal motion is less sensitive.