Search results for " materiali"
showing 10 items of 710 documents
Influence of sol counter-ions on the visible light induced photocatalytic behaviour of TiO2 nanoparticles
2014
Titanium dioxide (TiO2) nanoparticles are attracting increasing interest because of their superior photocatalytic and antibacterial properties. Here, aqueous titanium oxy-hydroxide sols were made, using a green synthesis method, from the controlled hydrolysis/peptisation of titanium isopropoxide. Three different mineral acids were used to peptise the sol (HNO3, HBr and HCl), and provide counter-ions. The influence of nitrate or halide sol counter-ions on size distributions of the starting sols were measured via photon correlation spectroscopy (PCS). Semi-quantitative phase composition analysis (QPA), on the gels thermally treated at 450 and 600 degrees C, was carried out via Rietveld refine…
Durability of biodegradable polymers for the conservation of cultural heritage
2019
The use of polymers for conservation of cultural heritage is related to the possibility to slow down or stop natural deterioration which, in many cases, corresponds to stopping the entrance of liquid water and to favour spontaneous water vapour removal. Unfortunately, hydrophobicity is generally favoured by surface roughness and thus competitive with transparency. It is therefore important to find an optimal balance hydrophobicity, transparency and durability (especially to photooxidation). However, polymers typically used for applications in this field come from non-renewable resources and are not biodegradable. In this work, the mechanical, structural and optical properties of PLA, PBAT a…
Static and dynamic mechanical properties of Arundo Donax fillers-epoxy composites
2014
Abstract Aim of this work is to investigate the feasibility of using a natural and inexpensive filler obtained by grinding the culms of Arundo Donax as reinforcement of epoxy resins. The effect of the content and size of Arundo Donax fillers on static and dynamic mechanical properties was evaluated showing that the composites exhibit higher tensile moduli, comparable flexural moduli and lower strength properties in comparison to the neat resin. Moreover, changes in the storage and the loss moduli only above the glass transition temperature (i.e. in the rubbery region) were found while neither significant shifts of tan δ peaks to higher temperatures nor reductions in the peak height of the c…
The effect of alkaline treatment on mechanical properties of kenaf fibers and their epoxy composites
2015
Abstract In this work, kenaf fibers were pre-treated in a NaOH solution (6% in weight) at room temperature for two different periods (48 and 144 h). The chemical treatment of kenaf fibers for 48 h allowed to clean their surface removing each impurity whereas 144 h of immersion time had detrimental effect on the fibers surface and, consequently, on their mechanical properties. Untreated and NaOH treated kenaf fibers (i.e. for 48 h) were also used as reinforcing agent of epoxy resin composites. The effect of the stacking sequence (i.e. using unidirectional long fibers or randomly oriented short fibers) and the chemical treatment on the static mechanical properties was evaluated showing that t…
Manufacture of marine composite sandwich structures
2016
Abstract The aim of this chapter is to present the main processes of manufacture of composite sandwich structures used in marine applications. In the introduction, sandwich structure classification and properties and advantages/disadvantages in their uses are presented. In the second and third section, the main used technologies to made sandwich are, respectively, described and compared. Then, the goodness of these techniques is evidenced with the discussion of some experimental results obtained by the authors in their studies. The last section concludes with a thorough list of the future trends.
Fracture behavior and mechanical, thermal, and rheological properties of biodegradable films extruded by flat die and calender
2020
The development of biodegradable materials for tailored applications, particularly in the field of polymeric films and sheets, is a challenging technological goal as well as a contribution to help protect the environment. Poly(lactic) acid (PLA) is a promising substitute for several oil-based polymers; however, to overcome its thermal and mechanical drawbacks, researchers have developed solutions such as blending PLA with polybutylene adipate terephthalate (PBAT), which is capable of increasing the ductility of the final material. In this study, PLA/PBAT binary blends, with minimum possible content of nonrenewable materials, were examined from processing, thermal, morphological, and rheolog…
Chemical Modification of Nitrile to Oxazoline Functionality on a Styrene-Acrylonitrile Copolymer in the Melt
1998
Oxazoline is a very interesting functionality for reactive extrusion and other applications. In this paper, we report the possibility of chemically transforming nitrile group attached to a copolymer of styrene and acrylonitrile (SAN) to oxazoline group using 2-amino-ethanol (AE). The chemical modification of SAN with AE was done in the molten state. Among various catalysts tested, zinc acetate turned out to be the most efficient. The effects of the catalyst concentration, temperature and mixing on the overall kinetics were studied. The formation of the expected oxazoline functionality was confirmed by infrared spectroscopy and by reacting with 1-naphthylacetic acid. The reaction between the…
Three-Point Flexural Behaviour of GFRP Sandwich Composites: A Failure Map
2010
In this work, the failure mechanisms of GFRP/PVC foam core sandwich structures subjected to three-point bending are analysed. By varying the skin thickness (t ) and the span length between supports (l), experimental tests were carried out in order to find the relationship between the geometrical configuration of the sandwiches and the failure mechanism. By plotting failure mechanism on a graph of l against t , a failure map was created identifying the three typical failure mode regions of these sandwiches. The graph clearly shows the failure mode corresponding to each combination of l and t . To help optimise the use of these sandwich beams as structural elements, a theoretical failure mode…
Effect of ultraviolet and moisture action on biodegradable polymers and their blend
2020
In this work, the suitability of polylactic acid (PLA), polybutylene adipate terephthalate (PBAT) and PBAT/PLA blend samples to outdoor applications were investigated in terms of mechanical, morphological and visual properties in presence of ultraviolet action and water, finding that PLA in particular can be actually considered for such applications.