Search results for " tecnologia."
showing 10 items of 1339 documents
Electromagnetic shielding efficiency in Ka-band: carbon foam versus epoxy/carbon nanotube composites
2012
The wide application of microwaves stimulates searching for new materials with high electrical conductivity and electromagnetic (EM) interference shielding effectiveness (SE). We conducted a comparative study of EM SE in K a -band demonstrated by ultra-light micro-structural porous carbon solids (carbon foams) of different bulk densities, 0.042 to 0.150 g/cm 3 , and conventional flexible epoxy resin filled with carbon nanotubes (CNTs) in small concentrations, 1.5 wt.%. Microwave probing of carbon foams showed that the transmission through a 2 mm-thick layer strongly decreases with decreasing the pore size up to the level of 0.6%, due to a rise of reflectance ability. At the same time, 1 mm…
Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers
2020
Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…
Collapsible intact soil stabilisation using non-aqueous polymeric vehicle
2020
Abstract This paper presents the results of an experimental study that had the goal of understanding the effects of treatment with polyethylene glycol (PEG)/nanolime mixtures on collapsible soil behaviour. In a previous study, the use of pure PEG offered a good improvement in the stability of collapsible soil, but the stabilisation effect only lasted for a limited time. To investigate the stabilisation potential of PEG/nanolime systems for collapsible sand, different mixtures were prepared at increasing nanolime weight ratios. The suitability of the stabilised soil was examined on the basis of collapsibility, oedometer, shear, and water vapour permeability tests, and through optical microsc…
Failure Map of Composite Laminate Mechanical Joint
2007
The aim of this research is to investigate the pin/hole contact stress of a composite laminate and failure modes when submitted to tensile bearing tests. The limit loads and failure modes are evaluated as a function of pin diameter and hole position. Analyzing the joint geometry effect on the fracture mechanisms, a failure map is obtained, identifying three regions of typical failure modes of mechanically fastened joints. A theoretical approach is proposed to identify the field of each fracture mode to obtain a simple experimental methodology to support the design of a particular joint laminate. In addition, a simplified numerical model is proposed to evaluate near the hole the stress/stra…
Graphene Oxide Carboxymethylcellulose Nanocomposite for Dressing Materials.
2020
Sore, infected wounds are a major clinical issue, and there is thus an urgent need for novel biomaterials as multifunctional constituents for dressings. A set of biocomposites was prepared by solvent casting using different concentrations of carboxymethylcellulose (CMC) and exfoliated graphene oxide (Exf-GO) as a filler. Exf-GO was first obtained by the strong oxidation and exfoliation of graphite. The structural, morphological and mechanical properties of the composites (CMCx/Exf-GO) were evaluated, and the obtained composites were homogenous, transparent and brownish in color. The results confirmed that Exf-GO may be homogeneously dispersed in CMC. It was found that the composite has an i…
Optimization of two-step techniques engineered for the preparation of polyamide 6 graphene oxide nanocomposites
2019
Abstract Different processing conditions to achieve polyamide 6 (PA6)-graphene oxide (GO) nanocomposites were investigated. GO was pre-dispersed in PA6 by three different solvent-based methods and, further, melt processed to prepare nanocomposites at two different loading levels, namely 2 and 5 wt.%. The evolution of rheological and mechanical properties was analyzed by investigating eventual changes in the microstructure and polymer crystallinity, aiming at providing a detailed processing-structure-properties relationship for these systems.
The influence of Al doping on the photocatalytic activity of nanostructured ZnO: The role of adsorbed water
2018
Abstract Al doped ZnO nanoparticles (labeled as x% A-ZnO, x = 0.0, 0.5, 1.0, and 1.5) were synthesized by a simple sol-gel method, characterized and tested as photocatalysts for the degradation of a model compound under UV-light irradiation. Diffuse reflectance spectroscopy (DRS) and photoelectrochemical analysis have been performed to evidence their optical and electronic behavior. The structural features of the powders were highlighted by means of specific surface area (SSA) analysis, X-ray diffraction (XRD), Fourier-transform infrared (FTIR) and Raman spectroscopy. Al doping results in enhanced photocatalytic activity of the modified powders with respect to pure ZnO. In particular, the h…
Absolute crystallinity and photocatalytic activity of brookite TiO2 samples
2017
Abstract This study reports a method to determine the absolute crystallinity of partly crystalline brookite TiO2 photocatalysts. A natural, a commercial and various home-prepared brookite powders were characterized by X-ray diffraction analysis, Raman spectroscopy, scanning electron microscopy, UV–vis diffuse reflectance spectroscopy and nitrogen adsorption measurements. The absolute crystallinity was calculated from the ratio between the full width at half maximum intensity of the (121) X-ray diffraction peaks of the brookite samples and the (111) peak of CaF2 as internal standard. The photocatalytic activity of the powders was tested employing the photodegradation of 4-nitrophenol as well…
Imbibition of Femtoliter-Scale DNA-Rich Aqueous Droplets into Porous Nylon Substrates by Molecular Printing
2019
This work presents the first reported imbibition mechanism of femtoliter (fL)-scale droplets produced by microchannel cantilever spotting (μCS) of DNA molecular inks into porous substrates (hydrophilic nylon). Differently from macroscopic or picoliter droplets, the downscaling to the fL-size leads to an imbibition process controlled by the subtle interplay of evaporation, spreading, viscosity, and capillarity, with gravitational forces being quasi-negligible. In particular, the minimization of droplet evaporation, surface tension, and viscosity allows for a reproducible droplet imbibition process. The dwell time on the nylon surface permits further tuning of the droplet lateral size, in acc…
Rapid One-Step Fabrication of Graphene Oxide-Decorated Polycaprolactone Three-Dimensional Templates for Water Treatment
2020
Coating of flexible substrates is crucial to prepare versatile, multifunctional materials. However, exploration of effective fabrication approaches is still a challenging issue, because the pathways generally proposed require time-consuming, multistep protocols. Here, we developed a one-pot process for decorating either pearl necklace-like or fibrous fluffy-like structures of polycaprolactone (PCL) with graphene oxide (GO) skin. PCL solutions were dry jet-wet electrosprayed or electrospun into a stirred liquid collector constituted by ethanol-containing GO nanoparticles. The stirred liquid collector enables the formation of 3D-structures, whose microarchitecture can be designed by controlli…