Search results for "ESI"
showing 10 items of 46722 documents
Flexible and efficient computer-aided design tool for advanced comb-line rectangular waveguide filters
2015
A very flexible and efficient computer-aided design CAD tool, specifically suited for advanced comb-line rectangular waveguide filters, is presented in this work. The developed software tool, which makes use of a full-wave analysis technique based on the Boundary Integral-Resonant Mode Expansion method, allows loading the considered comb-line resonators with any number of radially symmetrical partial-height metallic posts. The implemented CAD tool also allows dealing with coupling windows of arbitrary cross-section, thus drastically enhancing the flexibility of the CAD process. The excitation of the analyzed components, which is performed using generalized coaxial probes, has also been inte…
Experimental Equipment for Studying the Residual Stresses Developed During High Temperature Reactions by X-Ray Diffraction
1996
This paper describes a device dedicated to studyng, by X-ray diffraction the residual stresses developed on surface samples as a function of temperature and atmosphere conditions. The setup consists of : a.) an horizontal axis goniometer which allows the programmed positionning of the sealed X-ray source and of the linear detector. b.) a high temperature controlled atmosphere chamber Particular attention has been paid to the thermal stability up to 1200°C and the accurate position on the sample.
Analog isolated electronic dynamometer based on a magnetoresistive current sensor.
2017
In this work, an electronic system is presented to measure the force applied by a solenoid. The originality of the work is focused on the use of a magnetoresistive current sensor to provide the isolation barrier needed in the actual industrial plant where the solenoids are working. The design of the electronic system is presented as well as experimental measurements as a result of a calibration process showing a negligible hysteresis with that specific sensor. The magnetoresistive current sensor is used to develop transmission functions rather than playing its usual sensing roles.
Design and experimental validation of a magnetic device for stem cell culture.
2020
Cell culture of bone and tendon tissues requires mechanical stimulation of the cells in order to mimic their physiological state. In the present work, a device has been conceived and developed to generate a controlled magnetic field with a homogeneous gradient in the working space. The design requirement was to maximize the magnetic flux gradient, assuring a minimum magnetizing value in a 15 mm × 15 mm working area, which highly increases the normal operating range of this sort of devices. The objective is to use the machine for two types of biological tests: magnetic irradiation of biological samples and force generation on paramagnetic particles embedded in scaffolds for cell culture. The…
Electron transport and the effect of current annealing in a two-point contacted hBN/graphene/hBN heterostructure device
2020
In this work, we fabricated a 2D van der Waals heterostructure device in an inert nitrogen atmosphere by means of a dry transfer technique in order to obtain a clean and largely impurity free stack of hexagonal boron nitride (hBN)-encapsulated few-layer graphene. The heterostructure was contacted from the top with gold leads on two sides, and the device’s properties including intrinsic charge carrier density, mobility, and contact resistance were studied as a function of temperature from 4 K to 270 K. We show that the contact resistance of the device mainly originates from the metal/graphene interface, which contributes a significant part to the total resistance. We demonstrate that current…
Identification of induction motor thermal model for improved drivetrain design
2016
Selection of components of electric drivetrains is not only based on evaluating their ability to perform according to mechanical specifications, but — what is equally important — on assessing their thermal protection limits. These are typically affected by electrical and thermal properties of motors and drives. Although rated parameters (such as power, torque, speed, etc.) are easily accessible in catalogs of equipment producers, more specific properties like mass / length of copper winding, heat dissipation factor, rotor / stator dimensions etc. are not available to customers. Therefore, effective selection of drivetrain components is limited due to the lack of sufficient data and the need…
Strategies for numerical simulation of linear friction welding of metals: a review
2017
Linear friction welding (LFW) is a solid-state joining process used to weld non-axisymmetric components. Material joining is obtained through the reciprocating motion of two specimens undergoing an axial force. During this process, the heat source is determined by the frictional work transformed into heat. This results in a local softening of the material and plays a key role in the onset of the bonding conditions. In this paper, a critical analysis of the different approaches used to simulate the LFW processes is provided. The focus of the paper is the comparison of different modeling strategies and the most relevant outputs available, i.e. temperature, strain and stress distribution, mate…
Resistive communications based on neuristors
2017
Memristors are passive elements that allow us to store information using a single element per bit. However, this is not the only utility of the memristor. Considering the physical chemical structure of the element used, the memristor can function at the same time as memory and as a communication unit. This paper presents a new approach to the use of the memristor and develops the concept of resistive communication.
Space charge behavior of different insulating materials employed in AC and DC cable systems
2017
In this work, the space charge accumulation in three different XLPE based material has been carried out by using the PEA (Pulsed Electro-Acoustic) method. The specimens provided by a cables industry have been subjected to the same DC stress during polarization time at environment temperature. Afterwards, the high voltage generator has been turned off and the amount residual charge has been evaluated. The space charge profiles during polarization and depolarization have been carried out and compared. Finally, the distribution of electric field within the samples has been reported. In particular, the maximum distortion of electric field has been calculated by taking into account the distribut…
Electrical transport in lead-free (Na0.5Bi0.5)1–xSrxTiO3 ceramics (x = 0, 0.01 and 0.02)
2017
Lead-free (Na0.5Bi0.5)1xSrxTiO3 (x = 0, 0.01 and 0.02) ceramics were manufactured through a solid-state mixed oxide method and their ac (σac) and dc (σdc) electric conductivity were studied. It is ...