Search results for "Geotechnical engineering"
showing 10 items of 489 documents
Precipitation responses to ENSO and IOD in the Maldives: Implications of large-scale modes of climate variability in weather-related preparedness
2020
Abstract This research seeks to address the extent to which indices of large-scale modes of climate variability (El Nino Southern Oscillation (ENSO) and Indian Ocean Dipole (IOD)) can be linked to physical differences in the local mean and extreme rainfall conditions experienced in the Maldives in order to suggest implications for disaster risk reduction (DRR). While some significant differences in precipitation metrics do occur at the local level between different phases of the large-scale modes of climate variability studied, they do not occur for all sites studied. While the constrained availability of historical meteorological data in the region is a limiting factor in this analysis, th…
Boudinage classification: end-member boudin types and modified boudin structures
2004
In monoclinic shear zones, there are only three ways a layer can be boudinaged, leading to three kinematic classes of boudinage. These are (1) symmetrically without slip on the inter-boudin surface (no-slip boudinage), and two classes with asymmetrical slip on the inter-boudin surface: slip being either (2) synthetic (S-slip boudinage) or (3) antithetic (A-slip boudinage) with respect to bulk shear sense. In S-slip boudinage, the boudins rotate antithetically, and in antithetic slip boudinage they rotate synthetically with respect to shear sense. We have investigated the geometry of 2100 natural boudins from a wide variety of geological contexts worldwide. Five end-member boudin block geome…
Influence of column shear failure on pushover based assessment of masonry infilled reinforced concrete framed structures: A case study
2017
Structural frames, constructed either of steel or reinforced concrete (RC), are often infilled with masonry panels. However, during the analysis of the structural frames, it has become common practice to disregard the existence of infills because of the complexity in modeling. This omission should not be allowed because the two contributions (of infills and of frames) complement each other in providing a so different structural system. The use of different modeling assumptions significantly affects the capacity as well as the inelastic demand and safety assessment. In specific, the adoption of equivalent diagonal pin-jointed struts leaves open the problem of the evaluation of the additional…
ADV measurements of velocity distributions in a gravel-bed flume
2003
Velocity measurements carried out by an acoustic doppler velocimeter (ADV) in a rectangular laboratory flume having a gravel bed are presented. The velocity profiles are measured in six verticals of the channel cross-section having an increasing distance (from 4 to 38.5 cm) from the flume wall. The experimental runs are carried out for five different bed arrangements, characterized by different concentrations of coarser elements, and for the two conditions of small- and large-scale roughness. For both hydraulic conditions, the velocity measurements are first used to test the applicability of the Dean profile and of the logarithmic profile corrected by a divergence function proposed in this …
Non linear and linearized combination coefficients for modal pushover analysis
2017
Current design practice and seismic codes tend to assess seismic demand of buildings by Non linear Static Analysis (NSA), based on the evaluation of the pushover curve. Earlier non-linear static analysis procedure estimate the response peak value by evaluating the push-over curve adopting a distribution of invariant forces proportional to the fundamental vibration mode. In order to include the effect of higher modes several multimodal push-over analysis procedures were proposed in literature. In In the most famous of these, namely Modal Pushover Analysis (MPA), nodal response peak values are obtained by combination of "modal" responses by the traditional SRSS or CQC methods: the use of the …
Field and Numerical Tests of the Two-Ponding Depth Procedure for Analysis of Single-Ring Pressure Infiltrometer Data
2013
Abstract The two-ponding depth (TPD) analysis procedure of single-ring infiltrometer data can yield invalid results, i.e., negative values of the field-saturated soil hydraulic conductivity or the matric flux potential, denoting failure of the two-level run. The objective of this study was to test the performance of the TPD procedure in analyzing the single-ring infiltrometer data of different types of soils. A field investigation carried out in western Sicily, Italy, yielded higher failure rates (40%) in two clay loam soils than in a sandy loam soil (25%). A similar result, i.e., fine-textured soils yielding higher failure rates than the coarse-textured one, was obtained using numerically …
Definition of diagonal Poisson's ratio and elastic modulus for infill masonry walls
2014
The prediction of the response of infilled frames through the simplified approach of substituting the infill with an equivalent pin-jointed strut is treated. In this framework the results of an experimental study for the mechanical characterization of different types of masonry infills having the aim of estimating strength, Young modulus and Poisson's ratio are presented. Four types of masonry were investigated and subjected to ordinary compressive tests orthogonally to the mortar beds and along the directions of the mortar beds. The experimental campaign confirmed the possibility of using an orthotropic plate model for prediction of the Poisson's ratio and Young modulus along the diagonal …
Infilled frames: developments in the evaluation of the stiffening effect of infills
2003
In order to consider the modified seismic response of framed structures in the presence of masonry infills, proper models have to be formulated. Because of the complexity of the problem, a careful definition of a diagonal pin-jointed strut, able to represent the horizontal force-interstorey displacement cyclic law of the actual infill, may be a solution. In this connection the present paper shows a generalized criterion for the determination of the ideal cross-section of the strut mentioned before. The procedure is based on the equivalence between the lateral stiffness of the actual infilled frame scheme during the conventional elastic stage of the response and the lateral stiffness of the …
Advanced Strategies and Materials for Reinforcing Normal and Disturbed Regions in Brick Masonry Columns
2016
This work presents the results of an experimental investigation on the behavior of 42 solid clay brick masonry columns internally strengthened by fiber-reinforced polymer (FRP) fabrics or stainless steel grids placed in horizontal mortar joints. In some cases, every course, and in other cases, alternate courses were reinforced with steel grids, carbon, and basalt FRP fabrics. Monotonic compressive loading tests were carried out under concentric and eccentric loads. Eccentric tests were carried out by loading the specimens on a reduced area with respect to the entire cross section, producing a disturbed region (D-region). A detailed characterization of the constituent materials was made expe…
Ultrasonic inspection for the detection of debonding in CFRP-reinforced concrete
2017
Fibre-reinforced plastic (FRP) composites are extensively used to retrofit civil structures. However, the quality and the characteristics of the bond between the FRP and the structure are critical to ensure the efficacy of the retrofit. For this reason, effective non-destructive evaluation (NDE) methods are often necessary to assess the bonding conditions. This article presents an ultrasonic technique for detecting defects at the FRP-substrate interface. The technique uses the Akaike Information Criterion, to detect automatically the onset of the ultrasonic signals, and the novel Equivalent Time Lenght (ETL) parameter, to quantify the energy of the propagating ultrasonic signals along the i…