Search results for "Metallurgy"
showing 10 items of 1419 documents
Thermally Stimulated Ionic and Electronic Processes and Radiation-Induced Defect Annealing in LiBaF3 Crystals
2000
The electronic, ionic and ion-diffusion controlled thermally stimulated relaxation (TSR) processes in X-ray irradiated (at 80 K or 290 K) nominally pure LiBaF3 fluoroperovskite crystals have been investigated in the 90–550 K range by means of the ionic conductivity, ionic thermally stimulated depolarization current (TSDC), as well as the thermally stimulated current (TSC), thermally stimulated luminescence (TSL) and the X-ray induced optical absorption spectra thermal bleaching techniques. The role of the thermoactivated ionic and ionic-electronic processes in the TSR (thermal bleaching, TSC and TSL) of X-ray irradiated crystals is studied above 250 K. The TSL efficiency (ratio TSL/TSC) ver…
Structural anisotropy and annealing-induced nanoscale atomic rearrangements in metamict titanite
2012
The structural state of metamict titanite was studied by Raman spectroscopy, complementary high-resolution transmission electron microscopy, and single-crystal X-ray diffraction. The results show that Raman scattering collected from metamict titanite is highly anisotropic, which is typical of single crystals. But surprisingly, the observed Raman-scattering dependence on the sample orientation is much more pronounced for heavily metamict than for weakly metamict titanite samples. These radiation-induced anisotropic effects are related to the specific atomic arrangements in metamict titanite. The Raman spectra collected in backscattering geometry from a plane nearly perpendicular to the chain…
Photoelectrochemical removal of chlorfenvinphos by using WO3 nanorods: Influence of annealing temperature and operation pH
2019
[EN] A visible-light driven photoelectrochemical degradation process has been applied to a solution polluted with the organophosphate insecticide chlorfenvinphos. Different WO3 nanosheets/nanorods have been used as photoanodes. These nanostructured electrodes have been fabricated by anodization of tungsten and, subsequently, they have been subjected to a thermal treatment (annealing). The combined influence of annealing temperature (400¿°C and 600¿°C) and operation pH (1 and 3) on the photoelectrocatalytic behavior of these nanorods has been examined through a statistical analysis. Morphological, structural and photoelectrochemical characterizations have also been carried out. The chlorfenv…
Structure and properties of polyethyleneterephthalate crystallized by annealing in the highly oriented state
1976
The structure of polyethyleneterephthalate bristles drawn about five times in the amorphous state and subsequently crystallized at temperatures between 100 and 260‡ C has been studied by means of small-angle X-ray scattering. In addition density, heat of fusion and wide-angle scattering behaviour were measured. For comparison, similar experiments were carried out with undrawn samples. The results showed that the degree of crystallinity of PET cannot be calculated from density data on the basis of a simple two-phase model, since the effective densitiesρc* andρa* of the crystalline and amorphous regions depend strongly on crystallization and drawing conditions. With rising crystallization tem…
Effect of temperature–bias annealing on the hysteresis and subthreshold behavior of multilayer MoS2 transistors
2016
The transfer characteristics (ID-VG) of multilayers MoS2 transistors with a SiO2/Si backgate and Ni source/drain contacts have been measured on as-prepared devices and after annealing at different temperatures (T-ann from 150 degrees C to 200 degrees C) under a positive bias ramp (V-G from 0 V to + 20 V). Larger T-ann resulted in a reduced hysteresis of the ID-VG curves (from similar to 11 V in the as-prepared sample to similar to 2.5 V after Tann at 200 degrees C). The field effect mobility (similar to 30 cm(2) V-1 s(-1)) remained almost unchanged after the annealing. On the contrary, the subthreshold characteristics changed from the common n-type behaviour in the as-prepared device to the…
Tuning of the Mg Alloy AZ31 Anodizing Process for Biodegradable Implants
2021
Coatings were grown on the AZ31 Mg alloy by a hard anodizing process in the hot glycerol phosphate-containing electrolyte. Anodizing conditions were optimized, maximizing corrosion resistance estimated by impedance measurements carried out in Hank's solution at 37 °C. A post anodizing annealing treatment (350 °C for 24 h) allowed us to further enhance the corrosion resistance of the coatings mainly containing magnesium phosphate according to energy-dispersive X-ray spectroscopy and Raman analyses. Gravimetric measurements revealed a hydrogen evolution rate within the limits acceptable for application of AZ31 in biomedical devices. In vitro tests demonstrated that the coatings are biocompati…
Elaboration and characterization of barium silicate thin films.
2008
International audience; Room temperature depositions of barium on a thermal silicon oxide layer were performed in ultra high vacuum (UHV). In-situ X-ray photoelectron spectroscopy (XPS) analyses were carried out as well after exposure to air as after subsequent annealings. These analyses were ex-situ completed by secondary ion mass spectrometry (SIMS) profiles and transmission electron microscopy (TEM) cross-sectional images. The results showed that after air exposure, the barium went carbonated. Annealing at sufficient temperature permitted to decompose the carbonate to benefit of a barium silicate. The silicate layer was formed by interdiffusion of barium with the initial SiO2 layer.
Experimental and theoretical evidence for substitutional molybdenum atoms in theTiO2(110)subsurface
2006
Molybdenum was deposited at room temperature on the ${\mathrm{TiO}}_{2}(110)$ surface in the 0--1.3 equivalent monolayer (eqML) range and was then annealed at $400\phantom{\rule{0.2em}{0ex}}\ifmmode^\circ\else\textdegree\fi{}\mathrm{C}$ in order to reach a kind of equilibrium state. A threshold was found in the behavior of the deposit: below 0.2 eqML, substitutional molybdenum occurs in titanium sites located under the bridging oxygen atoms of the ${\mathrm{TiO}}_{2}(110)$ surface. In this position, molybdenum atoms are in a structural and chemical ${\mathrm{MoO}}_{2}$-like environment. Density-functional theory calculations show that this molybdenum site is actually the most stable one in …
A diamond (1 0 0) surface with perfect phase purity
2015
Abstract Diamond surfaces with (1 0 0) orientation and perfect phase purity regarding the coexistence of sp3 and sp2 bonding as well as near surface nitrogen implanted layers are repeatedly produced from one sample by a cycle of nitrogen implantation, etching in oxygen and wet chemical etching. Comprehensive surface studies carried out by X-ray photoelectron spectroscopy (XPS) involving a deconvolution of the C 1s peak into contributions of C sp3, C sp2 and C sp3(N) reveal the surface and near-surface phase and stoichiometry. It is demonstrated that efficient etching of nitrogen implanted diamond occurs by high temperature annealing in oxygen and a wet chemical treatment.
Understanding the Conversion Process of Magnetron-Deposited Thin Films of Amorphous ReO$_x$ to Crystalline ReO$_3$ upon Thermal Annealing
2020
Crystal growth & design 20(9), 6147 - 6156 (2020). doi:10.1021/acs.cgd.0c00848