Search results for "Metallurgy"
showing 10 items of 1419 documents
Efficient Vacuum-Deposited Perovskite Solar Cells with Stable Cubic FA 1– x MA x PbI 3
2020
Preparation of black formamidinium lead iodide (FAPbI3) requires high temperature annealing and the incorporation of smaller A-site cations, such as methylammonium (MA+), cesium or rubidium. A major advantage of vacuum processing is the possibility to deposit perovskite films at room temperature (RT), without any annealing step. Here we demonstrate stabilization of the cubic perovskite phase at RT, in a three-sources co-sublimation method. We found that the MA+ incorporation is a self-limiting process, where the amount of MA+ which is incorporated in the perovskite is essentially unvaried with increasing MAI deposition rate. In this way a phase-pure, cubic perovskite with a bandgap of 1.53 …
Positron annihilation studies of recrystallization in the subsurface zone induced by friction in magnesium—effect of the inhomogeneity on measured po…
2013
The discussion of the positron annihilation studies of crystal structure defects, like vacancies, dislocations, grain boundaries and the defect depth profile, is presented. The role of the positron implantation depth and positron diffusion in such studies has been considered in detail. For description of the measured annihilation characteristics the proposed theoretical models take into account both effects. The annealing studies of defects created in pure magnesium by compression or dry sliding-wear were used for demonstration of the discussed thesis. The positron lifetime measurements were applied for monitoring open volume defects behavior. It was demonstrated that annealing at the tempe…
Defects in Martensitic Stainless Steel 1.4031 (EN) Exposed to Friction as Seen by Positron Annihilation
2010
We present experimental results of measurements of the Doppler broadening of annihilation line and positron annihilation lifetimes in martensitic stainless steel 1.4031 (EN) samples exposed to the dry sliding under different loads. In particular, we tested the subsurface zone under the worn surfaces. As a main result, we obtained information about the defect profiles in this zone and the total extent of the damage region induced by the dry sliding.
Influence of nanoporous structure on mechanical strength of aluminium and aluminium alloy adhesive structural joints
2006
The influence of surface treatments on the mechanical strength of adhesive joints was investigated. The attention was focused on AA2024 alloy because it is extensively used in both the automotive and aerospace industries. Adhesive joints fabricated with pure aluminium were also investigated in order to evidence possible differences in the surface features after identical treatments. Before joining with a commercial epoxy adhesive, metal substrates were subjected to different kinds of treatment and the surfaces were characterized by SEM analysis. The formation of a microporous surface in the AA2024 alloy, upon etching and anodizing, is discussed on the basis of the role of the intermetallic …
Anodic oxide films on tungsten—II. The morphology and dissolution of the films
1980
Abstract Scanning electron microscopy was used to investigate the morphology of anodic oxide films on tungsten, obtained in various conditions of anodization. Studies were made of the growth of porous films, whose thickness increases with time and depends upon the current density. Temperature and electrolyte composition influence the film morphology. Gravimetric measurements of film dissolution at 70°C show that after a transient time, the rate of metal dissolution and that of film formation coincide. The porous films thicken because tungsten dissolves as WO 2 2+ and precipitates as WO 3 .H 2 O.
Electrochemical Determination of the Fe(III)/Fe(II) Ratio in Archaeological Ceramic Materials Using Carbon Paste and Composite Electrodes
2002
A method for determining the iron(III)/iron(II) ratio in ceramic materials based on microsample attachment to graphite/polyester composite electrodes is presented. This quotient is of considerable interest for determining the nature and firing conditions of the original materials in archaeological ceramics. The electrochemistry of iron in ceramic materials in acetic/acetate and Na2EDTA aqueous solutions is described in terms of reductive dissolution processes of iron(III) materials and oxidative dissolution processes of iron(II) ones. The iron(III)/iron(II) ratio is determined from peak area measurements in linear scan voltammograms performed in 0.10 M acetic/acetate buffer (pH 4.70) and 0.…
Corrosion behaviour of a highly alloyed austenitic alloy UB6 in contaminated phosphoric acid
2013
The influence of temperature (20–80°C) on the electrochemical behaviour of passive films anodically formed on UB6 stainless steel in phosphoric acid solution (5.5 M H3PO4) has been examined by using potentiodynamic curves, electrochemical impedance spectroscopy, and Mott-Schottky analysis. UB6 stainless steel in contaminated phosphoric acid is characterised by high interfacial impedance, thereby, illustrating its high corrosion resistance. The obtained results show that the films behave as n-type and p-type semiconductors in the potential range above and below the flat band potential, respectively. This behaviour is assumed to be the consequence of the semiconducting properties of the iron …
Ru-Based Thin Film Temperature Sensor for Space Environments: Microfabrication and Characterization under Total Ionizing Dose
2016
The paper shows the microfabrication processes of a Ruthenium-based resistance temperature detector and its behavior in response to irradiation at ambient temperature. The radiation test was done in a public hospital facility and followed the procedures based on the ESA specification ESCC 22900. The instrumentation system used for the test is detailed in the work describing the sensors resistance evolution before, during, and after the exposure. A total irradiation dose of 43 krad with 36 krad/h dose rate was applied and a subsequent characterization was performed once the Ru sensors were submitted to an 80°C annealing process during a period of 168 h. The experimental measurements have sho…
Using a neural network for predicting the average grain size in friction stir welding processes
2009
In the paper the microstructural phenomena in terms of average grain size occurring in friction stir welding (FSW) processes are focused. A neural network was linked to a finite element model (FEM) of the process to predict the average grain size values. The utilized net was trained starting from experimental data and numerical results of butt joints and then tested on further butt, lap and T-joints. The obtained results show the capability of the AI technique in conjunction with the FE tool to predict the final microstructure in the FSW joints.
Continuous dynamic recrystallization phenomena modelling in friction stir welding of aluminium alloys: A neural-network-based approach
2007
The current paper focuses on the continuous dynamic recrystallization phenomena (CDRX) occurring in friction stir welding processes of AA6082 T6 aluminium alloys. In particular, in order to predict the average grain size, a properly trained neural network is linked to the finite element method (FEM) model of the process. The utilized net, which takes as inputs the local values of strain, strain rate, and temperature, was trained starting from experimental data and numerical results. The obtained results show the capability of the artificial intelligence (AI) technique in conjunction with the FE tool to predict the final microstructure in the joint section.