Search results for "Metallurgy"
showing 10 items of 1419 documents
Corrosion behaviour of sintered Nd(Fe,Al)B magnets
1997
Abstract The effect of 1–6 at% Al additions to a sintered NdFeB magnet on its corrosion behaviour was tested. The additions do not influence the magnet's corrosion behaviour in the active state and cause beneficial effects in the passive state. The Al additions inhibit atmospheric corrosion of the magnets.
Mechanisms Involved by Reactive Elements upon High Temperature Chromia Scale Growth
2001
The influence of Y 2 O 3 , Pr 2 O 3 , Nd 2 O 3 , Sm 2 O 3 and Yb 2 O 3 coatings on Fe-30Cr alloy oxidation behaviour was investigated at 1000°C in air under atmospheric pressure. Isothermal exposures indicated that the Y 2 O 3 coating was the most protective after 100 hours. Pr 2 O 3 , Nd 2 O 3 and Sm 2 O 3 coatings were less effective, but the less beneficial effect was observed when Yb 2 O 3 coating was applied onto the Fe-Cr alloy surface. Two-stage oxidation experiments in 16 O 2 and then 18 O 2 were performed to get information about the chromia growth phenomena with and without reactive elements. The 18 O-tracer distribution was determined by secondary ion mass spectrometry (SIMS) and…
High temperature reactivity of nickel aluminide diffusion coatings
2008
Abstract The high-temperature oxidation behaviour of nickel aluminides has been studied at 900 °C in air under atmospheric pressure. Yttria doped and undoped specimens of nickel were aluminised and then oxidised for 100 h under isothermal and cycling conditions. The results showed that when yttria is added by metal-organic chemical vapour deposition technique prior to the aluminisation process, it increased the oxidation rate of aluminised nickel, but improved the oxide scale adherence under cyclic conditions. The effects of yttria on the scale morphology, oxidation behaviour and scale spallation tendency are discussed based on the experimental results, using X-ray diffraction (XRD), scanni…
Photoelectrochemical monitoring of rouging and de-rouging on AISI 316L
2017
Electrochemical conditions for inducing rouging on surface of AISI 316L in quasi neutral aqueous solution are studied. Potentiostatic polarization at 0.6 V vs. SSC at pH ∼ 7 allowed growth of colourless passive films with a band gap slightly lower than that estimated for the oxide grown on the SS surface by air exposure due to chromium dissolution. Under stronger anodic polarization (UE = 1.5 V vs. SSC) coloured passive films are formed, mainly constituted by iron oxide according to their band gap (Eg = 2.0 eV). Etching in citric acid at 60 °C results to be effective in removing rouging.
Photoelectrochemical evidence of inhomogeneous composition at nm length scale of anodic films on valve metals alloys
2016
Abstract Anodic films of different thickness (∼30 nm and 70 nm) were grown by anodizing sputtering-deposited Ta-19at% Al to different formation voltages. N incorporation into the anodic films was inducing by performing the anodizing process in ammonium containing solutions. Layered anodic films were prepared by a double formation procedure with a first anodizing step in ammonium biborate solution and second anodizing step in borate buffer solution, or vice versa. Glow Discharge Optical Emission Spectroscopy was employed to show the distribution of N across the oxide. Photoelectrochemical measurements evidenced a red shift of the light absorption threshold due to N incorporation. A model was…
Properties of Ni–Zn ferrite thin films deposited using spray pyrolysis
2012
Abstract Nanocrystalline, homogeneous spinel Ni 1 − x Zn x Fe 2 O 4 thin films were deposited on glass substrates by using spray pyrolysis of metal nitrate aqueous solutions. The thickness of deposited films was below 500 nm, but crystallite size was under 30 nm. It has been shown that the DC resistivity, dielectric loss and optical band gap of deposited films are influenced by the zinc content. High DC resistivity and low dielectric losses of thin Ni 1 − x Zn x Fe 2 O 4 films are explained by mixed n-p conductivity and nanograin structure of spray pyrolysis deposited coatings which are changing with the ratio of Ni/Zn.
Experimental Comparison of the MIG and Friction Stir Welding Processes for AA 6005 Aluminium Alloy
2015
In this study, the mechanical properties of welded joints of AA 6005 aluminum alloy obtained with friction stir welding (FSW) and conventional metal inert gas welding (MIG) are studied. FSW welds were carried out on a semi-automatic milling machine. The performance of FSW and MIG welded joints were identified using tensile and bending impact tests, as far as the environmental aspects are also included in the discussion. The joints obtained with FSW and MIG processes were also investigated in their microstructure. The results indicate that, the microstructure of the friction stir weld is different from that of MIG welded joint. The weld nugget consists of small grains in FSW than those found…
Microhardness and adhesion measurements of reactively sputtered TiN/AlN multilayer coatings deposited as function of mass-flow of nitrogen
1998
Abstract Multilayer coatings of (Ti, Al)N x have been deposited by reactive sputtering from Ti and Al targets in a side-by-side configuration on WC and stainless steel substrates. The rotation of the substrate holder varied from 2 to 14 r.p.m. corresponding to a bilayer thickness of 0.8–8 nm. The acoustic emission scratch technique for adhesion measurements was used for studying coating performance, and critical load values for the coatings on WC substrate up to 150 N were obtained. The Vickers microhardness in the load range 0.003–2 N was measured, and in order to obtain true hardness values, an optimal range of indentation depth and coating thickness was determined. Depending on the nitro…
New generation super alloy candidates for medical applications: Corrosion behavior, cation release and biological evaluation
2014
Three super alloy candidates (X1 CrNiMoMnW 24-22-6-3-2 N, NiCr21 MoNbFe 8-3-5 AlTi, CoNiCr 35-20 Mo 10 BTi) for a prolonged contact with skin are evaluated in comparison with two reference austenitic stainless steels 316L and 904L. Several electrochemical parameters were measured and determined (E(oc), E(corr), i(corr), b(a), b(c), E(b), R(p), E(crev) and coulometric analysis) in order to compare the corrosion behavior. The cation release evaluation and in vitro biological characterization also were performed. In terms of corrosion, the results reveal that the 904L steels presented the best behavior followed by the super austenitic steel X1 CrNiMoMnW 24-22-6-3-2 N. For the other two super a…
Response of human endothelial cells to oxidative stress on Ti6Al4V alloy.
2007
Titanium and its alloys are amongst the most frequently used materials in bone and dental implantology. The good biocompatibility of titanium(-alloys) is attributed to the formation of a titanium oxide layer on the implant surface. However, implant failures do occur and this appears to be due to titanium corrosion. Thus, cells participating in the wound healing processes around an implanted material, among them endothelial cells, might be subjected to reactive oxygen species (ROS) formed by electrochemical processes during titanium corrosion. Therefore, we studied the response of endothelial cells grown on Ti6Al4V alloy to H(2)O(2) and compared this with the response of endothelial cells gr…