Search results for "SHR"
showing 10 items of 455 documents
Numerical modeling and validation of hydrothermal liquefaction of a lignin particle for biocrude production
2021
Abstract Lignin liquefaction process under catalyst-free conditions in a temperature range from 573 K to 647 K is investigated with this mathematical model. Based on the theoretical understanding of the physical and chemical processes of the liquefaction process in subcritical temperatures, a comprehensive mathematical model for the decomposition of lignin by hydrolysis reaction pathway is developed on the results of a series of batch experiments. The model consists of four main sections. They are liquefaction of lignin particle, oily film, and inorganic (ash) layer formation behavior during the liquefaction, kinetic model to model further liquefaction process of initial products, and the l…
On the hydro-mechanical behaviour of a lime-treated embankment during wetting and drying cycles
2018
Abstract The paper presents some experimental results obtained on samples extracted from a full-scale embankment obtained by compacting a lime-treated clayey soil. A comprehensive test programme was carried out in order to highlight the improvement of mechanical behaviour induced by lime treatment as well as to assess the durability of the improved material, which may be affected by severe seasonal wetting and drying cycles. Direct shear tests, triaxial compression tests, swelling potential measurement and oedometric tests were performed on samples cured in controlled environmental conditions for at least 18 months. Wetting and drying cycles were applied in a very wide range of suction valu…
Effect of some injection molding processing conditions on weld lines characteristics
1988
The influence of injection and mold temperature as well as holding time on the knit-line characteristics in samples of Nylon 6 obtained by injection molding was analysed. The characteristics of the surface defect seem to be governed by the shrinkage rate and amount in the weld line zone.
Large Photonic Films by Crystallization on Fluid Substrates
2002
Cracks, which appear due to shrinkage during drying of artificial opaline films, strongly limit the use of these materials. Crystallization on fluid substrates (liquid metals) is a way to circumvent this problem. By this method it is possible to prepare crack-free three-dimensional “monocrystals” with a very low defect density and the size in millimeters.
EFFECT OF SHAPE ON POTATO AND CAULIFLOWER SHRINKAGE DURING DRYING
2000
ABSTRACT Shrinkage of potato cubes, parallelepipeds and cylinders was addressed during drying. A basic methodology by using image analysis was set-up in order to measure and monitor geometrical changes along the drying process. Both measurements by image analysis and directly with a calliper were carried out. Results from both methods showed a good agreement with no bias. Particle shape was found to influence shrinkage in a different way according to the axis. In fact the larger dimension shrinks less than the shorter one. This could be linked to the influence of the core drying in shrinkage. Experiments were also carried out for cauliflower stems. The difference in shrinkage between direct…
A plasticity model for predicting the rheological behavior of paperboard
2017
The sorption of water into the paperboard exposes a container to reversible and irreversible deformations under relative humidity variations. In this study, an elasto-plastic material model is used to demonstrate how through-thickness dry solids content gradients can generate permanent in-plane strains in paperboard. The measurements presented in this paper indicate that in consecutive loading-unloading cycles, the yield stress either remains roughly constant or decreases, and an additional permanent set of strain is obtained even when the maximum tension of repetitions stays constant. Two modified approaches concerning elasto-plastic hardening behavior based on the measurements of this wor…
Nanoporous kaolin
2017
Cellulose nano- and microfibrils (CNF/CMF) grades vary significantly based on the raw materials and process treatments used. In this study four different CNF/CMF grades were combined with kaolin clay pigment particles to form nanoporous composites. The attained composite properties like porosity, surface smoothness, mechanical properties and density properties depended strongly on the raw materials used. In general, higher kaolin content (~80 wt%) led to controllable shrinkage during drying, which resulted in improved dimensional stability of composites, compared to a lower kaolin content (~50 wt%). On the other hand, the use of a plasticizer and a high amount of CNF/CMF was essential to pr…
Subsignal-based denoising from piecewise linear or constant signal
2011
15 pages; International audience; n the present work, a novel signal denoising technique for piecewise constant or linear signals is presented termed as "signal split." The proposed method separates the sharp edges or transitions from the noise elements by splitting the signal into different parts. Unlike many noise removal techniques, the method works only in the nonorthogonal domain. The new method utilizes Stein unbiased risk estimate (SURE) to split the signal, Lipschitz exponents to identify noise elements, and a polynomial fitting approach for the sub signal reconstruction. At the final stage, merging of all parts yield in the fully denoised signal at a very low computational cost. St…
Form defect influence on the shrinkage fit characteristics
1998
Abstract Today, manufacturing products must meet more and more severe specifications. The different parts composing the product often necessitate high dimensional precision, which increases the difficulties for a large series production. Then it it necessary to optimize dimensioning of the different components in an economic context. In the case of small dimensional fits, there is an influence of the micro-geometry (form of defect, roughness) and time of the process on the geometrical characteristics of the assembly. At the time of conception, it is necessary to obtain a good specification that relates the product functionalities with the best cost. The objective study of this is to simulat…