Search results for "business.product_category"
showing 10 items of 376 documents
Theoretical and Experimental Studies on the Influence of Process Parameters on Strains and Forces of Single Point Incremental Forming
2014
These paper aims to determine the influence of the most important geometrical parameters (vertical step and punch diameter) on the main strains, thickness reduction and the forces along two directions during the single point incremental forming process (SPIF). The paper comprises a comparative numericalexperimental study, for a simple geometry part obtained by incremental forming. In fact, in the first stage, the punch has a vertical motion with the value of one vertical step. In the second stage, the punch follows a linear trajectory along one side of the die. After each linear trajectory the punch has successive vertical motions, taking one vertical step at a time until the entire geometr…
Orientation and Crystallinity Measurements in Film Casting Products
2003
Film casting experiments were carried out with iPP under processing conditions causing the crystallization process to occur under orienting flow. Draw ratio and cooling rates were changed by varying mass flow rates and die thickness. The effect of processing conditions on film crystallinity was investigated by combining WAXS and FT-IR transmission methods, while orientation of both phases was measured by IR dichroism (according to Fraser's method) and successfully compared to birefringence measurements on final films. Crystallinity appears to be almost insensitive to draw ratio and cooling rate. Moreover the crystallinity profile turned out to be also constant along the transverse film dire…
Capital Structure and Financial Control: The Effect of Leverage on Project Management
2015
Amplification characteristics are leveraging financial system which has a small risk of capability. However, the efficiency of this ability is the two-ways result and will also pose a lot of risks. Therefore, taking positive measures to strengthen the management of the financial system leverage feature in project management becomes very important. This paper describes the financial system leverage to bring the main problem through the lever amplification (nature) analysis of the characteristics, bi-amplified comparative analysis of profit and loss and bi-amplification characteristics of the risk analysis. Based on the above analysis, we put forward countermeasures about the management of le…
Process mechanics analysis in single point incremental forming
2004
The request of highly differentiated products and the need of process flexibility have brought the researchers to focus the attention on innovative sheet forming processes. Industrial application of conventional processes is, in fact, economically convenient just for large scale productions; furthermore conventional processes do not allow to fully satisfy the mentioned demand of flexibility. In this contest, single point incremental forming (SPIF) is an innovative and flexible answer to market requests. The process is characterized by a peculiar process mechanics, being the sheet plastically deformed only through a localised stretching mechanism. Some recent experimental studies have shown …
Study on heat transfer coefficients during cooling of PET bottles for food beverages
2015
The heat transfer properties of different cooling systems dealing with Poly-Ethylene-Terephthalate (PET) bottles were investigated. The heat transfer coefficient (Ug) was measured in various fluid dynamic conditions. Cooling media were either air or water. It was shown that heat transfer coefficients are strongly affected by fluid dynamics conditions, and range from 10 W/m2 K to nearly 400 W/m2 K. PET bottle thickness effect on Ug was shown to become relevant under faster fluid dynamics regimes.
Bonding prediction in friction stir consolidation of aluminum alloys: A preliminary study
2018
Friction Stir Consolidation (FSC) is a solid-state process that results in consolidation of metal powders or chips producing solid billet through severe plastic deformation and the solid-state bonding phenomena. This process can be used both for primary production and for metal scrap recycling. During the FSC process, a rotating die is plunged into a hollow chamber containing the finely divided, unconsolidated material to be processed. In this paper, a FEM numerical model for the prediction of the quality of the consolidated billet is presented. In particular, a dedicated bonding criterion that takes into account the peculiar process mechanics of this innovative technology is proposed.
Friction stir consolidation of aluminum machining chips
2017
Friction stir consolidation (FSC) is a solid-phase manufacturing process that consolidates metal powder, chips, or scraps into solid blocks via severe plastic deformation and solid state welding. It has the potential to be a more economical and âgreenâ process to recycle metal waste. In this study, solid discs were made from AA6061 aluminum alloy machining chips by FSC. The progression of the process was revealed by analyzing the motion of the tool, consolidating force, power history, and macro/microstructure of discs produced from a series of partial consolidation experiments. A bowl-shaped recrystallized zone in the vertical cross-sections of the disc products was observed and conside…
Supply and Demand of e-Government Services in Developing Countries: Cases from Tanzania
2013
One of the main contributions in order to create development in poor countries is to give people access to information and communication. Most people in poor countries cannot afford to buy their own computer equipment, and access has therefore to be facilitated by arrangements for public use. Today, Internet cafes and telecentres are the two main sources of public Internet access in developing countries. One area where information technology and public Internet access can be particularly useful for the development of poor countries is as a tool for promoting good governance through e-government systems. Generally, developing countries are lagging behind in e-government adoption, and in this…
Fatigue crack propagation from a cold-worked hole
2007
Abstract The cold expansion process is widely used to enhance the fatigue life of structures with fastener holes. Various studies assert that the cold expansion improves the fatigue strength of fastener holes; however, the improvement of fatigue life is difficult to quantify. Therefore, the influence on fatigue life of cold-worked process was studied by numerical and experimental tests. Then, a parametric study on material hardening behavior and Bauschinger’s parameter was performed for several loading conditions in order to determine their effect on crack growth propagation. The results of the numerical tests have exhibited a good prediction of the fatigue life of the component.
Hazards That Can Affect CNC Machine Tools during Operation—An AHP Approach
2020
CNC (computer numerically controlled) machine tools are highly advanced technological systems, used to machine parts by means of metal cutting processes. Their structure and kinematics are very complex, involving accurate coordinated motions on three to five axes. Operating CNC machine tools is a complicated process, which can easily be affected by errors. Nowadays, safety systems and devices are developed in order to make this process safer and more user friendly. Modern CNC controllers are designed to deal with obvious sources of hazards, such as overloads (by means of various sensor systems) and collisions (by checking the NC code syntax and simulating it on the machine). However, despit…