Search results for "manufacturing"
showing 10 items of 2299 documents
Simplified Modeling of Radiant Fields in Heterogeneous Photoreactors. 2. Limiting “Two-Flux” Model for the Case of Reflectance Greater Than Zero
1997
In the first part of this work a simple model for the description of the radiant field in heterogeneous photoreactors was developed, based on the assumption of zero reflectance of the particles. In this second part of the investigation a limiting model is developed in which the above hypothesis is removed. In this last model, scattering phenomena are dealt with in a very simple “two-flux” way, so that analytical solutions are obtained again. The case here developed is the same as in part 1, namely slab geometry with orthogonal parallel irradiation, giving special reference to the important case of semi-infinite reactor thickness. Both cases of solid catalysts with single particle size and w…
Process intensification in a photocatalytic membrane reactor: Analysis of the techniques to integrate reaction and separation
2017
Abstract Different methods to integrate reaction and separation in a membrane reactor are studied in the present work, with the aim being to highlight the pros and cons of the different alternatives and the effects of the intervening parameters. The coupling of the two processes can take place inside a single apparatus or using separate units. If a single apparatus is utilized, the coupling is more direct, but separate units offer higher degrees of freedom for the design with more opportunities to optimize the system without constraints. However, when using separate units, the integration of the two unit operations depends largely on the parameters intervening in the coupling procedure. The…
Comparative evaluation of the effect of the substrate thickness and inherent process defects on the static and fatigue performance of FSW and adhesiv…
2021
Abstract This work aims at evaluating the mechanical performance of joints in an AA6016 alloy, manufactured by means of two alternative processes: friction stir welding and adhesive bonding. Given its wide use in industrial fields such as automotive and aeronautics, an overlap configuration of joints was selected for the study, and a specific method based on the overlap length evaluation has been developed to allow comparisons among the cases. Two substrate thicknesses are considered in order to vary the overall joint stiffness, and the effect of such geometrical parameter on the mechanical behavior of the joined system is experimentally investigated. The experimental findings highlight tha…
Cutting Conditions and Work Material State Identification through Acoustic Emission Methods
1992
Summary This paper examines the problem of in-process monitoring of metal cutting operations carried out on aluminum alloys for aeronautical applications. Turning tests were conducted on annealed and heat treated aluminum alloy bars, using carbide tools. For both work material conditions, different combinations of cutting parameters were used. During cutting tests, acoustic emission (AE) and cutting force sensor data were detected and processed. The comparison between AE responses from the annealed and heat treated aluminum alloys allowed, with the help of force sensor data, to verify the applicability of AE and sensor fusion techniques for in-process and real time identification of work ma…
On the improvement of material formability in SPIF operation through tool stirring action
2012
Single-point incremental forming (SPIF) is a quite new sheet-forming process which offers the possibility to deform complex parts without dedicated dies using a single-point tool and a standard three-axis CNC machine. The process mechanics enables higher strains with respect to traditional sheet-forming processes, but particular attention must be given to the maximum forming angle. In this paper, a new approach is proposed to enhance the material formability through a localized sheet heating as a consequence of the friction work caused by elevated tool rotational speeds. AA1050-O, AA1050-H24, and AA6082-T6 were utilized, and the reached temperatures were recorded by thermocouples, fixed to …
Physics based modelling of interface temperatures in machining with multilayer coated tools at moderate cutting speeds
2004
Abstract A new thermal model is presented for turning with tools with multilayer coatings. In the previous paper [Int. J. Mach. Tools Manuf. 43 (2003) 1311] devoted to the thermal problems in dry turning of steels with tools treated with multilayer coatings with an intermediate Al 2 O 3 layer new analytical models for estimating the heat partition to the chip and the average interface temperature were derived and the predictions were compared with experimental results. In this paper, a physics based modelling concept has been applied to both the individual layer and the composite layer approach to develop an estimate of the average and the maximum steady-state chip-tool interface temperatur…
On the measurement of local gas hold-up, interfacial area and bubble size distribution in gas–liquid contactors via light sheet and image analysis: I…
2013
Abstract In this work a novel experimental technique for measuring local gas hold-up, interfacial area and bubble size distribution, in gas–liquid systems is proposed. The technique is based on advanced Image Processing coupled with experimental set-ups typically available for Particle Image Velocimetry. A fluorescent dye dissolved in the liquid phase allows to identify in-plane bubbles among all visible bubbles in the images. To this end, a suitable algorithm is proposed. The raw data so obtained are processed by previously developed statistical methods that result in a reliable reconstruction of actual dispersion properties. The technique is applied to the case of a gas-dispersed mechanic…
Optical properties of TiO2 suspensions: Influence of pH and powder concentration on mean particle size
2007
WOS: 000250584100025
Quasi-isoactinic reactor for photocatalytic kinetics studies
2007
Photochemical reactors characterized by almost uniform values of the local volumetric rate of photon absorption (LVRPA), i.e., quasi-isoactinic photoreactors, are particularly suitable for assessing the influence of radiant field intensity in kinetic studies. In this work, Monte Carlo simulations have been performed to obtain LVRPA values in a flat photoreactor irradiated on both sides. This configuration appears to be particularly suitable for obtaining quasi-isoactinic conditions. The influence of catalyst albedo and scattering phase function is assessed, and the conditions for obtaining iso-actinicity are discussed. Finally, these conditions are related to an easy-to-measure parameter, n…
Solid–Liquid Suspensions in Top-Covered Unbaffled Vessels: Influence of Particle Size, Liquid Viscosity, Impeller Size, and Clearance
2014
Particle suspension in liquids is a unit operation commonly encountered in the process industry. Although it is usually carried out in baffled stirred tanks, there are some specific applications where the presence of baffles may be undesirable. In the present work solid-liquid suspensions are investigated in a radially stirred unbaffled tank provided with a top cover. The minimum impeller speed at which all solid particles get suspended (Njs) and the relevant power requirements (Pjs) are assessed. The dependence of these two parameters on physical properties (liquid viscosity, particle concentration, and size) and system geometrical configurations (impeller diameter and clearance) is invest…