showing 11 related works from this author
How composition and process parameters affect volatile active compounds in biopolymer films
2012
Abstract Active edible films based on chitosan and containing an active aroma compound have been investigated. The influence of the composition of the film forming solution (solvent, plasticizers, nanoparticles, emulsifiers and aroma traps) and process parameters (temperature and viscosity) on drying kinetics, water content, colour, aroma compound retention and partition coefficient was studied. Solvent evaporation rate was increased by addition of ethanol. Water evaporation was delayed by glycerol. The aroma retention during film drying was directly related to the water content. The drying temperature had opposite influences according to the composition of the solvent and additives. Increa…
Carvacrol affects interfacial, structural and transfer properties of chitosan coatings applied onto polyethylene
2012
Different chitosan coating solutions were tested with the aim of investigating their adhesion and wettability onto polyethylene film to improve packaging performance and provide antimicrobial properties. Surface wetting kinetics was monitored by contact angle measurements. Addition of ethanol and carvacrol improved wettability and adhesion of the thin chitosan layer. Structure, water vapour, O2, CO2 and air permeabilities of self supported chitosan films and coated polyethylene were determined. The formation of a thin chitosan layer on polyethylene improved gas barrier properties decreasing the Permeability Coefficient for oxygen and carbon dioxide ( [Formula: see text] , [Formula: see text…
Effect of relative humidity on carvacrol release and permeation properties of chitosan based films and coating
2014
International audience; The influence of water vapour conditions on mass transport and barrier properties of chitosan based films and coatings were studied in relation to surface and structural properties. Water contact angles, material swelling, polymer degradation temperature, barrier properties (PO2, PCO2, WVP) and aroma diffusion coefficients were determined. The solvent nature and the presence of carvacrol influenced the surface and structural properties and then the barrier performance of activated chitosan films. Increasing RH from 0% to 100% led to a significant increase in material swelling. The plasticization effect of water was more pronounced at high humid environment, while at …
Technologies de conditionnement et procédés appliqués aux aliments emballés
2022
Ce chapitre couvre toutes les technologies du conditionnement pour les produits solides ou liquides déjà emballés ou non, utilisant tous types de matériaux flexibles ou rigides. Selon les traitements à appliquer après l’étape de conditionnement (stérilisation, refroidissement, cuisson, etc.), le choix de l’emballage est primordial pour conserver son intégrité.
Characterization of Food Packaging Films with Blackcurrant Fruit Waste as a Source of Antioxidant and Color Sensing Intelligent Material
2021
Chitosan and pectin films were enriched with blackcurrant pomace powder (10 and 20% (w/w)), as bio-based material, to minimize food production losses and to increase the functional properties of produced films aimed at food coatings and wrappers. Water vapor permeability of active films increased up to 25%, moisture content for 27% in pectin-based ones, but water solubility was not significantly modified. Mechanical properties (tensile strength, elongation at break and Young’s modulus) were mainly decreased due to the residual insoluble particles present in blackcurrant waste. FTIR analysis showed no significant changes between the film samples. The degradation temperatures, determined by D…
Structure and thermal properties of a chitosan coated polyethylene bilayer film
2012
The thermal and the structural properties of chitosan coated polyethylene (PE) films were studied. The coating process did not significantly influence the thermal stability and the PE surface structure and/or composition of the polyolefin. Dehydration temperature of chitosan films reflected the strength of water/acetic acid/chitosan chains interactions. Glycerol, used as a plasticizer, formed new hydrophilic centres in the film matrix. Moreover it was better integrated in the CSEGLY than in CSAGLY network. Besides, the addition of a plasticizer in the chitosan films decreased the film degradation temperature. There were two main steps for the PE chitosan coated films degradation. The first …
Novel functional chitosan and pectin bio-based packaging films with encapsulated Opuntia-ficus indica waste
2021
Abstract The aim of this work was to study the effect of adding red prickly pear, as wasted source of antioxidants on various characteristics of novel functional (antioxidant) chitosan and pectin film formulations. Four types of prickly pear material were used: fruit pulp or peel, as powdered extracts and as aqueous extracts. Prickly pear peel extract was shown to possess higher antioxidant properties than fruit pulp. The antioxidant power of extracts was pretty high, around 1000 mgAAE∙100 g−1 for extract and that of all films around 100 mgAAE∙100 g−1 for films. Even though some changes in thickness, moisture content, water solubility, oxygen permeability and water vapor permeability of fil…
Antioxidants and Bioactive Compounds in Food: Critical Review of Issues and Prospects
2022
International audience; This review paper gives an insight into the effective delivery mechanisms for health-promoting substances and highlights the challenges of using antioxidants and bioactives in foods. The selection criteria for choosing bioactives and their extraction in bioavailable form with their adequate incorporation techniques and delivery mechanisms are covered. Moreover, an overview of existing methods for determination of bioactivity is given. The importance of scientifically evaluating the effects of foods or food components on consumer health before making claims about the healthiness is aligned. Finally, a scientific perspective on how to respond to the booming demand for …
Effect of high power ultrasound on physical–chemical properties of polypropylene films aimed for food packaging: structure and surface features
2019
International audience; Biaxially oriented polypropylene (BOPP) coated with acrylic/polyvinylidene chloride (BOPPAcPVDC) and biaxially oriented coextruded polypropylene (BOPPcoex) films have been treated with high power ultrasound (HPUS) while submerged in water. Polymer structure and the surface morphology changes were noticed, and obtained results were correlated with the physical properties of tested materials. In anticipation of sonochemically enhanced reactions, physical–chemical profile of film samples was determined using thermogravimetric analysis, differential scanning calorimetry, Fourier-transform infrared spectroscopy, UV spectrophotometry and environmental scanning electron mic…
Influence of high power ultrasound on physical-chemical properties of polypropylene films aimed for food packaging: barrier and contact angle features
2017
Investigation was focused on the impact of high power ultrasound (HPUS), also called thermosonication, on the oxygen permeation properties (permeability, solubility and diffusion coefficients) of barrier films aimed for food packaging. For this purpose, biaxially oriented polypropylene (BOPP) coated with acrylic/polyvinylidene chloride (BOPPAcPVDC) and biaxially oriented coextruded polypropylene (BOPPcoex) were used. The physical–chemical profile of the samples was determined using goniometry. There is a significant impact only of extreme HPUS conditions (the longest time and the highest amplitude) on the permeability, solubility and diffusion coefficients of oxygen through the BOPP films. …
Barrier properties of chitosan coated polyethylene
2012
The transfer properties of chitosan coated polyethylene (PE) films were studied. The barrier properties of non coated PE were not affected by relative humidity changes. The presence of the hydrophilic chitosan layer acted as a water reservoir on the polyethylene film surface which significantly promoted its sensitivity to the water vapour. The water vapour permeability increased 1.85 times at a higher RH. Coated PE films showed more than two-order decrease in the oxygen permeability (PO2) and three-order-decrease in the carbon dioxide permeability (PCO2). When the chitosan coated PE surface was exposed to the water vapour, the PO2 and the PCO2 were significantly increased. However, the perm…