0000000000182481
AUTHOR
Isabella Mehling
showing 9 related works from this author
Intramedullary nailing vs. palmar locked plating for unstable dorsally comminuted distal radius fractures: A biomechanical study
2010
Abstract Background The purpose of this study was to compare the stability of a 2.4 mm palmar locking compression plate and a new intramedullary nail-plate-hybrid Targon DR for dorsally comminuted distal radius fractures. Methods An extraarticular 10 mm dorsally open wedge osteotomy was created in 8 pairs of fresh frozen human radii to simulate an AO–A3-fracture. The fractures were stabilized using one of the fixation methods. The specimens were loaded axially with 200 N and dorsal-excentrically with 80 N. 2000 cycles of dynamic loading and axial loading-to-failure were performed. Findings Axial loading revealed that intramedullary osteosynthesis (Targon DR: 369 N/mm) was significantly ( p …
(i) Comminuted patellar fractures
2006
Summary Purpose of review This article reviews current best practice for the diagnosis and treatment of comminuted patellar fractures. Recent findings Patellar fractures make up about 1% of all fractures. As a rule, fractures of the patella are caused by direct trauma to the knee. A transverse fracture is the most common fracture type. Open reduction and internal fixation is the treatment of choice for the majority of displaced patellar fractures. Treatment must achieve anatomic reduction of the articular surface and reestablish the continuity of the extensor mechanism. Tension-band wiring, interfragmentary screw fixation and a combination of cerclage wiring and screw fixation are the most …
Are there any differences in various polyaxial locking systems? A mechanical study of different locking screws in multidirectional angular stable dis…
2012
Numerous angular stable plates for the distal radius exist, and technically based comparisons of the polyaxial locking interfaces are lacking. The aim of this mechanical study was to investigate three different locking interfaces of angular stable volar plates by cantilever bending: VA-LCP Two-Column Distal Radius Plates 2.4 mm (Synthes® GmbH, Oberdorf, Switzerland), IXOS® P4 (Martin, Tuttlingen, Germany) and VariAX™ (Stryker®, Duisburg, Germany). We assessed the strength of 0°, 5°, 10° and 15° screw locking angles and tested the bending strength from 10° to 5° angles by cyclic loading until breakage. The final setup repeated the above assessments by inclusion of four locking screws. The si…
Number and Locations of Screw Fixation for Volar Fixed-Angle Plating of Distal Radius Fractures: Biomechanical Study
2010
Purpose To compare the biomechanical properties of different numbers and locations of screws in a multidirectional volar fixed-angle plate in a distal radius osteotomy cadaver model. Methods We created an extra-articular fracture in 16 pairs of fresh-frozen human cadaver radiuses. The 32 specimens were randomized into 4 groups. All fractures were fixated with a multidirectional volar fixed-angle plate. We tested 4 different screw-placement options in the distal fragment. The distal fragment was fixed with 4 locking screws in the distal row of the plate in group a, and with 4 locking screws alternately in the distal and proximal rows in group b. In group c, 3 locking screws were used in the …
Intraoperative C-arm CT imaging in angular stable plate osteosynthesis of distal radius fractures
2013
The purpose of this study was to analyze the practicability and benefit of intraoperative C-arm computed tomography (CT) imaging in volar plate osteosynthesis of unstable distal radius fractures. During a 1 year period, intraoperative three dimensional (3D) imaging with the ARCADIS Orbic 3D was performed in addition to standard fluoroscopy in 51 cases. The volar angular stable plate oesteosyntheses were analyzed intraoperatively and, if necessary, improved immediately. The duration of the scan and radiation exposure dose were measured. On average, performance of the scan and analysis of the CT dataset took 6.7 minutes. In 31.3% of the surgeries a misplacement of screws was detected and cor…
Progress of instability in fragility fractures of the pelvis: An observational study.
2019
Abstract Fragility fractures of the pelvis (FFP) are an increasing entity among elderly persons. Characteristics are different from high-energy pelvic trauma. Little is known about the natural course of FFP in conservative and after operative treatment. Materials and methods Medical charts and radiologic data of 148 patients with an FFP, who were admitted in a 3-year period, were analysed retrospectively. Incidence and characteristics of fracture progression (FP) were noted. Results Patients presenting early after a traumatic event had more often non-displaced fractures, fractures with lower FFP Type classification and were more frequently treated conservatively. FP was observed in 21 cases…
Stabilization of fatigue fractures of the dorsal pelvis with a trans-sacral bar. Operative technique and outcome.
2012
Abstract Introduction Due to ageing of our population the number of fatigue fractures of the pelvic ring is steadily growing. These fractures are often treated with bed rest but may result in a disabling immobility with severe pain. An operative treatment is an option in these cases. The aim of operative treatment is bony healing obtained by stable fixation giving back to the patient's previous mobility. Optimal surgical treatment is currently under debate. Sacroiliac screw fixation and sacroplasty are used for stabilization of the dorsal pelvis. Due to the technique and the low density of spongious sacral bone, no or only low compression in the fracture site is obtained, which may inhibit …
Locking Reconstruction Double Plating of Distal Humeral Fractures: How Many Screws in the Distal Ulnar Column Segment in A3 Fracture Provide Superior…
2009
Objectives: Two 90-degree configurations of locking reconstruction plates with different numbers of screws in the distal ulnar column segment of distal extra-articular humeral fractures with metaphyseal comminution (A3) were biomechanically investigated. Methods: Eight pairs of fresh-frozen human humeri were used. For paired comparison, the humeri were divided into 2 randomized groups. In both groups, double-plate osteosyntheses with locking reconstruction plates were performed in 90-degree configurations. In group 1, the posteriorly placed radial column plate exceeded the capitellum and the ulnar column plate extended into the ulnar sulcus. The ulnar plate was molded around the medial epic…
Volar Fixed-Angle Plating of Distal Radius Fractures
2011
The purpose of this biomechanical study was to determine whether a multidirectional fixed-angle plate with locking screws or with locking pegs in the distal fragment would optimize fixation of Orthopaedic Trauma Association (OTA) type A3 distal radius fractures.Eight pairs of fresh-frozen human distal radii were used. Extra-articular distal radius fractures were created and stabilized with a multidirectional volar fixed-angle plate. The radii were randomized into 2 matched-paired groups. The distal fragment in Group I was stabilized with 7 locking screws. The distal fragment in Group II was fixed with 7 locking pegs. The proximal fragment in both groups was fixed with 3 screws. The specimen…