Polymer solar cells with novel fullerene-based acceptor

2004

Abstract Alternative acceptor materials are possible candidates to improve the optical absorption and/or the open circuit voltage of polymer–fullerene solar cells. We studied a novel fullerene-type acceptor, DPM-12, for application in polymer–fullerene bulk heterojunction photovoltaic devices. Though DPM-12 has the identical redox potentials as methanofullerene PCBM, surprisingly high open circuit voltages in the range V OC =0.95 V were measured for OC 1 C 10 -PPV:DPM-12-based samples. The potential for photovoltaic application was studied by means of photovoltaic characterization of solar cells including current–voltage measurements and external quantum yield spectroscopy. Further studies …

Removing Leakage and Surface Recombination in Planar Perovskite Solar Cells

2019

Thin-film solar cells suffer from various types of recombination, of which leakage current usually dominates at lower voltages. Herein, we demonstrate first a three-order reduction of the shunt loss mechanism in planar methylammonium lead iodide perovskite solar cells by replacing the commonly used hole transport layer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) with a better hole-selective polyarylamine. As a result, these cells exhibit superior operation under reduced light conditions, which we demonstrate for the extreme case of moonlight irradiance, at which open-circuit voltages of 530 mV can still be obtained. By the shunt removal we also observe the VOC to dro…

Persistent photovoltage in methylammonium lead iodide perovskite solar cells

2014

Open circuit voltage decay measurements are performed on methylammonium lead iodide (CH3NH3PbI3) perovskite solar cells to investigate the charge carrier recombination dynamics. The measurements are compared to the two reference polymer-fullerene bulk heterojunction solar cells based on P3HT:PC60BM and PTB7:PC70BM blends. In the perovskite devices, two very different time domains of the voltage decay are found, with a first drop on a short time scale that is similar to the organic solar cells. However, two major differences are also observed. 65-70% of the maximum photovoltage persists on much longer timescales, and the recombination dynamics are dependent on the illumination intensity.

Radiative efficiency of lead iodide based perovskite solar cells

2014

The maximum efficiency of any solar cell can be evaluated in terms of its corresponding ability to emit light. We herein determine the important figure of merit of radiative efficiency for Methylammonium Lead Iodide perovskite solar cells and, to put in context, relate it to an organic photovoltaic (OPV) model device. We evaluate the reciprocity relation between electroluminescence and photovoltaic quantum efficiency and conclude that the emission from the perovskite devices is dominated by a sharp band-to-band transition that has a radiative efficiency much higher than that of an average OPV device. As a consequence, the perovskite have the benefit of retaining an open circuit voltage ~0.1…

Unravelling steady-state bulk recombination dynamics in thick efficient vacuum-deposited perovskite solar cells by transient methods

2019

Accurately identifying and understanding the dominant charge carrier recombination mechanism in perovskite solar cells are of crucial importance for further improvements of this already promising photovoltaic technology. Both optical and electrical transient methods have previously been employed to strive for this warranted goal. However, electrical techniques can be strongly influenced by the capacitive response of the device which hides the carrier recombination dynamics that are relevant under steady state conditions. To ascertain the identification of steady state relevant charge carrier dynamics, it is beneficial to evaluate thicker films to minimize the impact of device capacitance. H…

Reduced Recombination Losses in Evaporated Perovskite Solar Cells by Postfabrication Treatment

2021

The photovoltaic perovskite research community has now developed a large set of tools and techniques to improve the power conversion efficiency (PCE). One such arcane trick is to allow the finished devices to dwell in time, and the PCE often improves. Herein, a mild postannealing procedure is implemented on coevaporated perovskite solar cells confirming a substantial PCE improvement, mainly attributed to an increased open-circuit voltage (V\(_{OC}\)). From a V\(_{OC}\) of around 1.11 V directly after preparation, the voltage improves to more than 1.18 V by temporal and thermal annealing. To clarify the origin of this annealing effect, an in-depth device experimental and simulation character…

Transient drift‐diffusion simulation of the open circuit voltage decay in ionic perovskite solar cells

2021

Efficient Monolithic Perovskite/Perovskite Tandem Solar Cells

2016

Thin-film solar cells suffer from various types of recombination, of which leakage current usually dominates at lower voltages. Herein, we demonstrate first a three-order reduction of the shunt loss mechanism in planar methylammonium lead iodide perovskite solar cells by replacing the commonly used hole transport layer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) with a better hole-selective polyarylamine. As a result, these cells exhibit superior operation under reduced light conditions, which we demonstrate for the extreme case of moonlight irradiance, at which open-circuit voltages of 530 mV can still be obtained. By the shunt removal we also observe the VOC to dro…