Wear mechanisms and residual stresses in alumina-based laminated cutting tools

2005

Abstract The outstanding performances of the Al2O3 cutting tools in terms of potential cutting speed can lead to substantial economies in the machining of metallic materials. Nevertheless, their widespread use is limited by some drawbacks such as the tendency to edge chipping and to the propagation of microcracks, which can lead to premature failures. These shortcomings are due to the intrinsic low toughness of the ceramic material, which is in turn related to its characteristics non-metallic bonds. A well-recognised method of increasing the toughness of brittle materials is the introduction of surface compressive stresses, which can be obtained through a suitable lamination geometry of the…

TH-302 + Gemcitabine (G + T) vs Gemcitabine (G) in Patients with Previously Untreated advanced Pancreatic Cancer (PAC)

2012

ABSTRACT Background TH-302 is a hypoxia targeted prodrug with a hypoxia-triggered 2-nitroimidazole component designed to release the DNA alkylator, bromo-isophosphoramide mustard (Br-IPM), when reduced in severe hypoxia. A randomized Phase 2B study (NCT01144455) was conducted to assess the benefit of G + T to standard dose G as first-line therapy of PAC. Materials and methods An open-label multi-center study of two dose levels of TH-302 (240 mg/m2 or 340 mg/m2) in combination with G versus G alone (randomized 1:1:1). G (1000 mg/m2) and T were administered IV over 30-60 minutes on Days 1, 8 and 15 of a 28-day cycle. Patients on the G could crossover after progression and be randomized to a G…

WEAR PERFORMANCE OF CERAMIC CUTTING-TOOL MATERIALS WHEN CUTTING STEEL

1991

Abstract Some test cycles have been carried out in continuous cutting conditions, employing cutting parameters (feed, depth of cut and cutting speed) chosen following experimental planes and suitable test fields. The wear tests have been carried out on AISI 1040 steel with cutting speeds from 5m/sec to 11m/sec. The silicon nitride, sintered carbide, cubic boron nitride and alumina reinforced with SiC whiskers inserts, have shown, at each assigned cutting parameter, poor wear resistance when cutting steel. Alumina and alumina in submicron grain, which has been toughened by ZrO2 phase transformation, and the oxide-based alumina, have been the better wear resistance. The mixed based alumina ha…

Wear rates and wear mechanisms of alumina-based tools cutting steel at a low cutting speed

1997

Abstract Three ceramic insert materials, zirconia-toughened alumina (Al 2 O 3 –7vol%ZrO 2 ), mixed-based alumina (Al 2 O 3 –TiN–TiC–ZrO 2 ) and alumina reinforced with SiC whiskers (Al 2 O 3 –SiC w ), were used to cut AISI 1040 steel at 3.9 m s −1 . In addition, a traditional grade P10 insert (WC–TiC–Co) was tested. The lifetimes, according to KT/KM and VB B criteria, were determined using a profilometer and by image processing. The worn zones were observed with scanning electron microscopy techniques. Adhesion and plastic deformation were dominant wear mechanisms in zirconia-toughened alumina, mixed-based alumina and sintered carbide P10, both in the craters and in the cutting edges. As we…

The performance of molybdenum toughened alumina cutting tools in turning a particulate metal matrix composite

2003

In this paper, a study of the tool wear mechanism in turning aluminium alloy reinforced with alumina using molybdenum-toughened alumina tools is presented. Alumina tools with three different amounts (15, 20 and 25 vol.%) of molybdenum were prepared and tested. The wear type was identified and its evolution with cutting time was measured. The results show that the main mechanism of tool wear is abrasion and not heat. The best overall performance was achieved, as far as flank wear is concerned, using the tool with 20 vol.% of molybdenum added. This has been explained using some of the composites intrinsic properties. SEM examination revealed that molybdenum particles are easily torn from the …

Ceramic materials wear mechanisms when cutting nickel-based alloys

1999

Abstract In this paper the performances of some commercial ceramic inserts when cutting AISI 310 steel are investigated and compared to those of a traditional carbide based tool. The most important wear mechanism in the ceramic inserts is related to the segmented edges of the chips that abrade a notch at the end of the cut zone. Alumina–zirconia inserts are very sensitive to this kind of wear, whereas tools made of Sialon and alumina with SiC whiskers exhibit slightly better performances despite the concomitant chemical wear mechanisms.

Performances of Three Layered Ceramic Composites Inserts for Steel Cutting

1999

Sandwich-structured three-layered ceramic inserts were made with the aim of obtaining ceramic cutting tools with an increased useful life.

Cutting Temperatures Evaluation in Ceramic Tools: Experimental Tests, Numerical Analysis and SEM Observations

1994

The authors propose a multiple approach for the evaluation of cutting temperatures in ceramic tools. The first approach was the experimental evaluation of equitemperature lines, obtained in three-dimensional cutting by employing constant melting point powders scattered on planes parallel to rake face. In the second approach, a numerical finite element analysis was performed. At this step the determination of the percentage of total heat produced in the operation that flows into the tool was considered and, consequently, the temperature distribution within the whole volume of the insert. Finally, the examination of the crater zone with SEM microscopy confirmed the temperature levels as previ…

Wear mechanism and residual stresses in alumina-based laminated cutting

2005

Machining of Steel with Advanced Ceramic Cutting-Tools

1995

WEAR MECHANISM OF CERAMIC TOOLS

1993

Abstract Cutting tests were performed using ceramic cutting tools under continuous cutting conditions. The tests were carried out on AISI 1040 steel, with cutting speeds ranging from 5 to 11 m s −1 . The wear mechanism was investigated for both crater and flank. Alumina-toughened zirconia of submicron grain size showed the best wear resistance. Alumina with TiC, TiN and ZrO 2 inclusions exhibited a wear resistance a little lower than the above-mentioned materials. Low chemical stability seems to be the reason for the poor performances of the silicon carbide whiskers-reinforced alumina, silicon nitride and the tungsten carbide inserts.

The effect of wear on the tetragonal-to-monoclinic transformation and the residual stress distribution in zirconia-toughened alumina cutting tools

1998

Abstract Zirconia-toughened alumina cutting tools have been examined after machining an AISI 1040 steel. The Raman spectrum of zirconia and the fluorescence spectrum from alumina have been used to determine the extent of the tetragonal-to-monoclinic (t-m) transformation and the residual stresses in and around the worn-out crater, respectively. Although about 15% vol. m-zirconia is present even in a brand new cutting tool, it was shown that the crater region undergoes the t-m transformation up to 40% vol. In both cases, the transformed zone is concentrated near the surface. The residual stresses in alumina are slightly compressive in the new cutting tool and away from the crater region, but …