Search results for " Corrosion"
showing 10 items of 152 documents
Coated interconnects development for high temperature water vapour electrolysis: Study in anode atmospher
2013
International audience; High temperature water vapour electrolysis (HTE) is an efficient technology for hydrogen production. In this context, a commercial stainless steel, K41X (AISI 441), was chosen as interconnect. In a previous paper, the high temperature corrosion and the electrical conductivity were evaluated in both anode (O-2-H2O) and cathode (H-2-H2O) atmosphere at 800 degrees C. In O-2-H2O atmosphere, the formation of a thin chromia protective layer was observed. Nevertheless, the ASR parameter measured was higher than the maximum accepted value. These results, in addition with chromium evaporation measurements, proved that the K41X alloy is not suitable for HTE interconnect applic…
The multi-effects of K2TiF6 additive on the properties of PEO coatings on AZ31 Mg alloy
2020
Abstract Plasma electrolytic oxidation of AZ31 Mg alloy was performed in an alkaline silicate-based solution containing various concentrations of K2TiF6 using unipolar waveform at a constant voltage. The surface morphology of all coatings was rough and contained a micro-pore network, micro-cracks, and granules of oxide compounds in different diameters and micro-pore levels. The coating is composed of MgO, MgF2, Mg2SiO4, SiO2 (amorphous), and TiO2 (crystalline and amorphous) phases. The average thickness of the coatings was increased by adding the K2TiF6, where EDS results showed that a skinny fluoride-rich passive layer forms. With increasing time and reaching the final potential, the TiO2 …
Role of the Microstructure on the High Temperature Oxidation Properties of the Intermetallic Compound NbAl<sub>3</sub>
2001
The influence of the NbAl 3 microstructure on its oxidation mechanism was investigated in air under atmospheric pressure over the temperature range 500-1080°C. Different processing techniques as induction melting and mechanically-activated annealing processes (M2AP) were used to produce the intermetallic compound NbAl 3 . A protective external alumina scale grew only on Al-enriched NbAl 3 between 700 and 1080°C. Stoichiometric NbAl 3 exhibited the pesting phenomenon between 550-900°C, whereas a non protective lamellar oxide scale formed above 900°C. The proposed oxidation mechanism explains these observations which are in agreement with the oxidation study of powders with different crystall…
Corrosion behaviour of sintered Nd(Fe,Al)B magnets
1997
Abstract The effect of 1–6 at% Al additions to a sintered NdFeB magnet on its corrosion behaviour was tested. The additions do not influence the magnet's corrosion behaviour in the active state and cause beneficial effects in the passive state. The Al additions inhibit atmospheric corrosion of the magnets.
Mechanisms Involved by Reactive Elements upon High Temperature Chromia Scale Growth
2001
The influence of Y 2 O 3 , Pr 2 O 3 , Nd 2 O 3 , Sm 2 O 3 and Yb 2 O 3 coatings on Fe-30Cr alloy oxidation behaviour was investigated at 1000°C in air under atmospheric pressure. Isothermal exposures indicated that the Y 2 O 3 coating was the most protective after 100 hours. Pr 2 O 3 , Nd 2 O 3 and Sm 2 O 3 coatings were less effective, but the less beneficial effect was observed when Yb 2 O 3 coating was applied onto the Fe-Cr alloy surface. Two-stage oxidation experiments in 16 O 2 and then 18 O 2 were performed to get information about the chromia growth phenomena with and without reactive elements. The 18 O-tracer distribution was determined by secondary ion mass spectrometry (SIMS) and…
Risk of failure in existing RC balcony and strength verification under degradation phenomena
2020
Abstract In the present paper, the safety conditions of reinforced concrete (RC) balconies subject to degradation phenomena caused by carbonation, presence of chlorides or water infiltration were examined. After a brief review of the typical damages of balconies occurring with detachments of plaster and bricks expulsion, some cases of collapses of balconies recently occurred were presented. Therefore, a calculation model was proposed for a hand verification of the flexural and shear strength of existing corroded T beams cast in place of lightened RC orthotropic slabs forming the balcony and for the calculus of deflection including slippage of steel bars. Diffused and pitting corrosion on st…
The pore structure of compacted and partly saturated MX-80 bentonite at different dry densities
2014
Compacted MX-80 bentonite is a potential backfill material in radioactive-waste repositories. Pore space in MX-80 has been the subject of considerable debate. 3D reconstructions of the pore space based on tomographic methods could provide new insights into the nature of the pore space of compacted bentonites. To date, few such reconstructions have been done because of problems with the preparation of bentonite samples for electron microscopy. The nanoscale intergranular pore space was investigated here by cryo-Focused Ion Beam nanotomography (FIB-nt) applied to previously high-pressure frozen MX-80 bentonite samples. This approach allowed a tomographic investigation of the in situ microstru…
A three-dimensional cohesive-frictional grain-boundary micromechanical model for intergranular degradation and failure in polycrystalline materials
2013
Abstract In this study, a novel three-dimensional micro-mechanical crystal-level model for the analysis of intergranular degradation and failure in polycrystalline materials is presented. The polycrystalline microstructures are generated as Voronoi tessellations, that are able to retain the main statistical features of polycrystalline aggregates. The formulation is based on a grain-boundary integral representation of the elastic problem for the aggregate crystals, that are modeled as three-dimensional anisotropic elastic domains with random orientation in the three-dimensional space. The boundary integral representation involves only intergranular variables, namely interface displacement di…
Characterizing archaeological bronze corrosion products intersecting electrochemical impedance measurements with voltammetry of immobilized particles
2017
Application of electrochemical impedance measurements to microparticulate deposits of copper corrosion products attached to graphite electrodes in contact with 0.10 M aqueous HClO4 electrolyte is described. The impedance measurements were sensitive to the applied potential and the amount of solid sample and were modeled taking into account the contribution of the uncovered base electrode. Several pairs of circuit elements provide monotonic variations which are able to characterize different corrosion compounds regardless the amount of microparticulate solid on the electrode. Application to a set of archaeological samples from the archaeological Roman site of Gadara (Jordan, 4th century AD) …
The combined effect of refractory coatings containing reactive elements on high temperature oxidation behavior of chromia-forming alloys
2003
Abstract The high temperature oxidation behaviors of chromia-forming alloys (F17Ti and Fe–30Cr alloys) have been studied at 1273 K under isothermal conditions and at 1223 K under cyclic conditions, in air under the atmospheric pressure. To extend the oxidation lifetime, coatings have been applied onto the alloy surfaces. Al2O3 and Cr2O3 films doped with Sm2O3 or Nd2O3 were prepared via the metal-organic chemical vapor deposition technique. Single Cr2O3, Al2O3, Nd2O3 and codeposited Cr2O3–Nd2O3, Al2O3–Nd2O3, Al2O3–Sm2O3 coatings drastically improved the chromia-forming alloy high temperature oxidation behavior, since they decreased the oxidation rate and enhanced the oxide scale adhesion. Re…