Search results for " Macchi"
showing 10 items of 975 documents
A novel clustering-based algorithm for solving spatially-constrained robotic task sequencing problems
2021
The robotic task sequencing problem (RTSP) appears in various forms across many industrial applications and consists of developing an optimal sequence of motions to visit a set of target points defined in a task space. Developing solutions to problems involving complex spatial constraints remains challenging due to the existence of multiple inverse kinematic solutions and the requirements for collision avoidance. So far existing studies have been limited to relaxed RTSPs involving a small number of target points and relatively uncluttered environments. When extending existing methods to problems involving greater spatial constraints and large sets of target points, they either require subst…
Robotic geometric and volumetric inspection of high value and large scale aircraft wings
2019
Increased demands in performance and production rates require a radical new approach to the design and manufacturing of aircraft wings. Performance of modern robotic manipulators has enabled research and development of fast automated non-destructive testing (NDT) systems for complex geometries. This paper presents recent outcomes of work aimed at removing the bottleneck due to data acquisition rates, to fully exploit the scanning speed of modern 6-DoF manipulators. The geometric assessment of the parts is carried out with a robotised dynamic laser scanner encoded through an absolute laser tracker. This method allows scanning speeds up to 330mm/s at 1mm pitch. State of the art ultrasonic ins…
Algorithmic Approach for Slot Filling Factors Determination in Electrical Machines
2018
In several industrial sectors, such as electric and hybrid traction, the demand for increasingly efficient and high power density electrical machines has grown considerably over the last few years. The improvement of slot filling factor of the electrical machines is an useful provision to satisfy this request. In particular, this topic has been the subject of interest for the industrial sector in recent years, since the technology of winding processes have evolved and allow an economically sustainable realization of windings with an ordered structure rather than randomly. The winding phase must be supported by an accurate design process in which it is possible to evaluate the maximum slot f…
Sensorless Speed Control for Double-Sided Linear Induction Motor Applications
2019
In this work, a flux and speed observer for double-sided linear induction motor applications is presented and experimentally validated. More in detail, from a Double-Sided Linear Induction Motor (DLIM) prototype, the complete modelling and the determination of the related parameters are here reported. Furthermore, the equations for a d-flux and q-flux observer are conceived and several simulation tests are performed. From the good agreements between the trends over time of the speed estimated by the observer and the simulated one, it can be stated that the observer is well designed. Moreover, in order to experimentally validate the proposed observer, a test bench is set-up for the DLIM/obse…
Design of a telescopic tower for wind energy production with reduced environmental impact
2019
A prototype of a telescopic pole for wind energy production with low environmental impact and its lifting system for a 60 to 250 kW turbine and a height of 30 m have been designed and manufactured. A telescopic tower, which is raised and lowered by automation or by remote control, allows to differentiate the presence of the generator within the landscape over time. The technology currently available for lifting and lowering wind turbines is made up of telescopic poles of heights of less than 10 meters and with tilting posts of height below 30 m. Without a state of the art to refer to, the telescopic pole and its lifting system have been designed starting from scratch and solving with innova…
A flexible robotic cell for in-process inspection of multi-pass welds
2020
Welds are currently only inspected after all the passes are complete and after allowing sufficient time for any hydrogen cracking to develop, typically over several days. Any defects introduced between passes are therefore unreported until fully buried, greatly complicating rework and also delaying early corrections to the weld process parameters. In-process inspection can provide early intervention but involves many challenges, including operation at high temperatures with significant gradients affecting acoustic velocities and, hence, beam directions. Reflections from the incomplete parts of the weld would also be flagged as lack-of-fusion defects, requiring the region of interest (ROI) t…
Evaluation of Coded Excitations for Autonomous Airborne Ultrasonic Inspection
2019
Unmanned Aerial Vehicles (UAVs) are receiving increasing attention for use in Non-Destructive Testing due to their ability to access areas where manual inspection is not practical. Contact-based UAV ultrasonic inspections grant the opportunity to remotely monitor the structural health of an industrial asset with enhanced internal integrity information. Ultrasonic inspection is a Non-Destructive Testing (NDT) method conventionally used in corrosion mapping. Surface contacting ultrasonic transducers provide enhanced structural integrity information. However, due to near-surface aerodynamic effects, angular sensitivity of the ultrasound probe and alignment error during autonomous inspections, …
Cohesive Model for the Simulation of Crack Initiation and Propagation in Mixed-Mode I/II in Composite Materials
2019
A cohesive element able to connect and simulate crack growth between independently modeled finite element subdomains with non-matching meshes is proposed and validated. The approach is based on penalty constraints and has several advantages over conventional FE techniques in disconnecting two regions of a model during crack growth. The most important is the ability to release portion of the interface that are smaller than the local finite element length. Thus, the growth of delamination is not limited to advancing by releasing nodes of the FE model, which is a limitation common to the methods found in the literature. Furthermore, it is possible to vary the penalty parameter within the cohes…
SAFETY CONSIDERATIONS ON TEENAGE PEDESTRIAN-BUS IMPACT
2019
This work studies the impact conditions between the adolescent pedestrian and the bus focusing on head and chest injury. The injury to the head is analyzed using both the Head Injury Criterion (HIC) 36 and the HIC15 parameters as established by the most advanced legislation and comparing the risk probability Abbreviated Injury Scale (AIS3+) and AIS4+. The parameter HIC15 gives a higher probability of risk with lower values, and therefore it can be considered more conservative. Moreover, the study of chest injury is performed with two different biomechanical parameters: the Thoracic Trauma Index (TTI) and the TTI(d); the last neglects the pedestrian mass. The results indicate that the param…