Search results for " OPT"
showing 10 items of 13620 documents
A Novel Solution for the Elimination of Mode Switching in Pump-Controlled Single-Rod Cylinders
2020
This paper concerns the stability issue of pump-controlled single-rod cylinders, known as mode switching. First, a review of the topic is provided. Thereafter, the most recently proposed solution for the elimination of mode switching is investigated and shown to result in unstable behavior under certain operating conditions. A theoretical analysis is provided demonstrating the underlying mechanisms of this behavior. Based on the analysis, a novel control strategy is proposed and investigated numerically. Proper operation and stability are demonstrated for a wide range of operating conditions, including situations under which the most recently proposed solution results in unstable behavior a…
A Comparison Study of a Novel Self-Contained Electro-Hydraulic Cylinder versus a Conventional Valve-Controlled Actuator—Part 1: Motion Control
2019
This research paper presents the first part of a comparative analysis of a novel self-contained electro-hydraulic cylinder with passive load-holding capability against a state of the art, valve-controlled actuation system that is typically used in load-carrying applications. The study is carried out on a single-boom crane with focus on the control design and motion performance analysis. First, a model-based design approach is carried out to derive the control parameters for both actuation systems using experimentally validated models. The linear analysis shows that the new drive system has higher gain margin, allowing a considerably more aggressive closed-loop position controller. Several b…
Assembly Assistance System with Decision Trees and Ensemble Learning
2021
This paper presents different prediction methods based on decision tree and ensemble learning to suggest possible next assembly steps. The predictor is designed to be a component of a sensor-based assembly assistance system whose goal is to provide support via adaptive instructions, considering the assembly progress and, in the future, the estimation of user emotions during training. The assembly assistance station supports inexperienced manufacturing workers, but it can be useful in assisting experienced workers, too. The proposed predictors are evaluated on the data collected in experiments involving both trainees and manufacturing workers, as well as on a mixed dataset, and are compared …
Density Flow in Dynamical Networks via Mean-Field Games
2016
Current distributed routing control algorithms for dynamic networks model networks using the time evolution of density at network edges, while the routing control algorithm ensures edge density to converge to a Wardrop equilibrium, which was characterized by an equal traffic density on all used paths. We rearrange the density model to recast the problem within the framework of mean-field games. In doing that, we illustrate an extended state-space solution approach and we study the stochastic case where the density evolution is driven by a Brownian motion. Further, we investigate the case where the density evolution is perturbed by a bounded adversarial disturbance. For both the stochastic a…
Vision guided robotic inspection for parts in manufacturing and remanufacturing industry
2020
AbstractEnvironmental and commercial drivers are leading to a circular economy, where systems and components are routinely recycled or remanufactured. Unlike traditional manufacturing, where components typically have a high degree of tolerance, components in the remanufacturing process may have seen decades of wear, resulting in a wider variation of geometries. This makes it difficult to translate existing automation techniques to perform Non-Destructive Testing (NDT) for such components autonomously. The challenge of performing automated inspections, with off-line tool-paths developed from Computer Aided Design (CAD) models, typically arises from the fact that those paths do not have the r…
Mobile manipulator performance measurement towards manufacturing assembly tasks
2016
Mobile manipulator performance measurement research is relatively minimal as compared to that of robot arms. Measurement methods, such as optical tracking systems, are useful for measuring the performance of mobile manipulators, although at a much higher relative cost as compared to artifacts. The concept of using test artifacts demonstrates to potential manufacturers and users of mobile manipulator systems that relatively low cost performance measurement methods exist. This paper discusses the concept of reconfigurable mobile manipulator artifacts that were designed and built. An artifact was then used through experimentation to measure the performance of a mobile manipulator to demonstrat…
Current fault signatures of Voltage Source Inverters in different reference frames
2016
This paper considers different current patterns used to identify the correct fault signatures in Voltage Source Inverters (VSI). At the beginning, the Authors consider the currents patterns from which a simple or a double fault can be encompassed both in the case of controllable device only or with its free wheeling companion diode. After the discussion of diagnosis algorithm suitable for electrical drives and principally based on a persistent near zero current condition current in the natural phase reference frame, the stationary reference frame is then considered as a tool to identify both the faulted phase as the device or various combination of faulted devices. On the contrary, the Auth…
Enhancing tracking performance in a smartphone-based navigation system for visually impaired people
2016
In this paper we show how to enhance the tracking performance of Arianna, a low-cost augmented reality system designed to meet the needs of people with problems of orientation, people with sight impairment and blind people. For augmented reality system we mean the design of: i) a set of paths and tags to be deployed in the environment, realized in various ways depending on the context (decorative elements easily identifiable, colorful stripes, QR code, RFID, etc.); ii) an instrument of mediation between the reality and the user (typically a smartphone) to access the information disseminated in the environment by means of a camera and provide a vibration feedback signal to the users for foll…
A Pareto optimal design approach for simultaneous control of thinning and springback in stamping processes
2009
One of the most relevant research issues in automotive field is focused on the reduction of stamped parts weight also increasing their strength. In this way, a strong research effort is developed on high strength steels which are widely utilized and they require a proper springback control. Springback reduction in sheet metal forming is a typical goal to be pursued which is conflicting with thinning reduction for instance. Thus, such problems can be considered as multi-objective ones characterized by conflicting objectives. What is more, nowadays, a great interest would be focused on the availability of a cluster of possible optimal solutions instead of a single one, particularly in an indu…
Integration of gradient based and response surface methods to develop a cascade optimisation strategy for Y-shaped tube hydroforming process design
2010
International audience; In the last years a strong research effort was produced in order to develop and design new forming technologies able to overcome the typical drawbacks of traditional forming operations. Among such new technologies, hydroforming proved to be one of the most promising. The design of tube hydroforming operations is mainly aimed to prevent bursting or buckling occurrence and such issues can be pursued only if a proper control of both material feeding history and internal pressure path during the process is performed.In this paper, a proper optimisation strategy was developed on Y-shaped tube hydroforming process which is characterized by a quite complex process mechanics…