Search results for " Permanent"
showing 10 items of 144 documents
Microleakage in Class II composite restorations with margins below the CEJ: in vitro evaluation of different restorative techniques.
2012
Objectives: The purpose of this in vitro study was to evaluate the microleakage in "deep" Class II composite restorations with gingival cavosurface margin below the CEJ (cemento-enamel junction) and restored with different techniques. Study Design: Fifty human teeth were used. In each tooth two standardized Class II slot cavities (on mesial and on distal surfaces) were prepared: the buccolingual extension of the cavities was 4 mm; the gingival wall was located in dentin/cementum (2 mm beyond the CEJ). The prepared teeth were randomly assigned to 5 experimental groups (of 10 specimens and 20 cavities each) and restored. Group 1: Filtek TM Supreme XTE Flowable (3MESPE) + Universal Filtek Supr…
Marginal integrity of class V restorations: SEM versus dye penetration.
2006
To perform an in vitro investigation on the marginal integrity of different adhesives (Optibond FL, Scotchbond 1XT, Clearfil SE Bond, Adper Prompt L-Pop, S(3) Bond, iBond exp., Adper Prompt L-Pop) in combination with Tetric Ceram as well as an experimental silorane-restorative (Hermes, Hermes Bond; 3M ESPE) using SEM and dye penetration (2% methylene blue) in a comparative manner.Standardized class V-cavities (3 mm x 1.5 mm) were prepared in 70 extracted human teeth (n=10). The adhesives were applied according to manufacturers' instructions. The cavities were restored with three increments. After finishing and polishing (Sof-Lex discs) and thermocycling (5000x, 5/55 degrees C), replicas wer…
Evolución de la educación permanente y tendencias en el siglo XXI
2015
Dado que la Educación Permanente ocupa hoy en día un lugar relevante, el presente artículo plantea la visión de la evolución de la educación permanente y dos tendencias bien diferenciadas que, a nuestro juicio, emergen por una parte desde la UNESCO y por otra desde la Unión Europea. Todo esto para llegar a reflexionar sobre el paradigma filosófico-educativo más adecuado para la educación permanente en una escuela de adultos del Siglo XXI. En definitiva, se argumenta la necesidad de potenciar un perfil de profesorado que permita desarrollar una educación integral para todos y a lo largo de toda la vida.
El procés d'informació i orientació professional: aproximació al perfil de l'orientador
2008
Durant els últims anys, el concepte d'educació permanent, també anomenat Life Long Learning, ha estat objecte de debat en el disseny de polítiques i accions educatives a Europa. L'orientació professional constitueix un element estructural i funcional del sistema educatiu i formatiu amb un objectiu clar: l'èxit d'una inserció professional i social satisfactòria de la persona. L'orientació professional comprèn aspectes d'informació acadèmica i laboral juntament amb altres aspectes fonamentals com és ara el coneixement de la persona i les possibilitats de l'entorn. La informació acadèmica i professional és un element imprescindible per a l'orientació. L'orientació professional s'ha de dirigir …
Accumuler le capital humain tout au long de la vie: Quels facteurs prédictifs de la participation à la formation permanente?
2003
This article addresses the main predictors of adult education, using statistical methods different from those generally used by social science researchers. Its aim is twofold. First, it seeks to explain in a simple and comprehensible manner the methodological value of these methods (in relation to the use of structural models); secondly, it demonstrates the concrete usefulness of these methods on the basis of a recent piece of research on the data from the International Adult Literacy Survey (IALS).
Control and design for efficiency improvement of permanent-magnet synchronous motor drives in household appliances
2011
This paper deals with some aspects of efficiency improvement of PMSMD (Permanent Magnet Synchronous Motor Drives). Particularly two aspects are focused: the control algorithm for the PMSMD, which allows to reduce the power losses of the electric drive without penalty on its dynamic performances and the optimization of an IPMSM (Interior Permanent Magnet Synchronous Motor) rotor configuration capable to increase the performances in terms of shaft torque production, limiting at the same time the rotor leakage flux. The loss minimization algorithm is here briefly analyzed, a test bed for experimental validation is presented and the data are analyzed. Experimental tests have been performed aimi…
Comparison between 3-ph and 6-ph PMSM drives for the electric propulsion of unmanned aerial vehicles
2021
The full electric aircraft concept requires accurate design and suitable choice and integration of all the used components. Obviously, the electric propulsion drive is one of the most important on-board equipment. Both power converters and electric motors must have low weight, suitable overload capacity and high reliability. In this paper, two possible solutions of electric propulsion motor for unmanned aerial vehicle are investigated. Sizes, weight and some features of a three-phase PMSM motor are compared to those of a six-phase motor obtained by an appropriate rewinding of the armature, with fixed stator and rotor magnetic circuits. The losses obtained from the numerical analyzes are com…
Optimization of a Sea Wave Energy Harvesting Electromagnetic Device
2008
This paper presents the optimization of a permanent magnet linear generator directly coupled to sea waves. In order to maximize energy extraction, the stochastic features of the energy source is included in the mathematical model of the system in order to satisfactorily tackle the problem. An optimization procedure which includes the stochastic features of the model is presented and a machine built on the basis of the results of this procedure is shown.
Développement d'un procédé électrochimique pour le recyclage du néodyme à partir de déchets électroniques
2018
Neodymium belongs to the lanthanide’s serie of the period system and is the key component of the permanent magnets Nd2Fe14B which are implemented in electronic devices and “green” technologies like wind turbines or electric cars and bicycles. Nowadays, only one percent of the neodymium in electronic scraps is recycled. Due to the geopolitical considerations and a strong increase of the use of permanent magnets, there is an impoverishment of the raw material resources leading to an instable market.Since some decades, few recycling processes have been developed on a lab scale without any upscaling to the industrial scale. The existing processes have several drawbacks like multiple steps to ob…
Local DoS applications with micro wind generation systems
2015
In this paper a wind electrical power generation system for Distributed on Site (DoS) applications is proposed. This system was developed and conceived in order to guarantee simple installation, use and service, obtaining a product that can be easily industrialized and put into the market with limited costs. The field of application of such an electrical generation system is addressed towards domestic or at the most toward condominium applications concerning moreover the opportunity of working in addition to combined photovoltaic and solar-thermal systems to enhance the renewable energy generation at house level (DoS). The proposed system has its hot spot in the blades shape, in the wind fl…