Search results for " Rubber"

Measurement of dynamic characteristics of latex foams by the antiresonance method

2000

Measuring and calculation methods for the dynamic characteristics of tubular specimens of low-modulus latex foams and composites based on them, under longitudinal vibrations in a low-frequency region (up to 200 Hz), are developed. The method is based on the effect of antiresonance. Data on the influence of the basic formulation-processing factors on the dynamic characteristics (gelatination time and content of the plasticizer and chopped fibers) are presented. The results obtained can be used to choose the composition of latex foams for lining acoustic channels, injectors, ejectors, and phase inverters, as well as to control products quality. This method can be applied directly to full-size…

TI: Compatibilization of PA6/rubber blends by using an oxazoline functionalized rubber

2003

The compatibilization of blends of polyamide 6 with a nitrile butadiene rubber has been investigated. The procedure consists of two steps: modification of the nitrile groups of the rubber into oxazoline in the melt through condensation of ethanolamine with formation of a molecule of ammonia, followed by use of the modified rubber as a compatibilizing precursor which is melt mixed with the polyamide to produce the compatibilized blend. The modification reaction has been detected by NMR analysis and a rheological, mechanical and thermomechanical characterization has been carried out on the all the blends. The results indicate that the modification reaction occurs but the conversion of nitrile…

Effect of CTBN rubber inclusions on the curing kinetic of DGEBA–DGEBF epoxy resin

2003

Abstract The curing kinetics of an epoxy resin matrix, based on diglycil ether of bisphenol A and F (DGEBA–DGEBF), associated with an anhydride hardener, at different carboxyl-terminated copolymer of butadiene and acrylonitrile liquid rubber (CTBN) concentration (0–10 phr) are studied using a differential scanning calorimetry (DSC) and a stress-controlled rheometer in isothermal and dynamic conditions. The aim of this work is to correlate the presence of the rubber phase with the transition phenomena that occur during the curing process. The CTBN rubber induces a catalytic effect on the polymerization of the pure resin clearly observed by a significant enhancement of the curing rate. Calori…

Poisson's ratio and the incompressibility relation for various strain measures with the example of a silica-filled SBR rubber in uniaxial tension tes…

2010

Abstract The controversy in the definition of Poisson's ratio (PR) as a material constant is discussed in this study. PR of an isotropic material is usually defined as the ratio, taken with the opposite sign, between its lateral and longitudinal strains under the action of longitudinal stresses. However, if deformations of the material are large, the value of PR depends on the strain measure used. Five different measures of strain are considered, and a unified relation in terms of stretch ratios is obtained for calculating the PR. It is demonstrated that only for Hencky strains is the value of PR of an incompressible material constant and equal to 0.5 over its entire extension range. Other …

Modeling the influence of mineral content and porosity on ultrasound parameters in bone by using synthetic phantoms

1999

Model composite media − 10×15×80 mm3 bone tissue phantoms based on an epoxy resin with fillers—were made to study the influence of porosity and mineral content on ultrasound velocity and attenuation. The pores were simulated by ∼ 1 mm3 particles of a soft rubber, while the mineral content was imitated by a mineral residue of natural bone obtained by burning and grinding. The porosity and mineral content were varied in the range of 0–70% by volume with a step of 10%. The velocity, attenuation, and prevalent frequency of ultrasound were measured by the pulse transition method, using transducers with nominal frequencies 0.1, 0.2, 0.5, and 1.0 MHz. It was experimentally found that the ultrasoun…

Preparation and Characterization of Composites Materials with Rubber Matrix and with Polyvinyl Chloride Addition (PVC)

2020

An important problem that arises at present refers to the increase in performances in the exploitation of the conveyor belts. Additionally, it is pursued to use some materials, which can be obtained by recycling rubber and PVC waste, in their structure. Thus, the research aimed at creating conveyor belts using materials obtained from the recycling of rubber and PVC waste. Under these conditions, conveyor belts were made that had in their structure two types of rubber and PVC, which was obtained by adding in certain proportions of reclaimed rubber and powder obtained from grinding rubber waste. In order to study the effect of adding PVC on properties, four types of conveyor belts were made, …

Rutting analysis of different rubberised stone mastic asphalt mixtures: from binders to mixtures

2021

Stone Mastic Asphalt (SMA) has been broadly used on heavily trafficked roads and motorways in the UK due to its known stability and durability. In this study, several sets of SMA mixtures were produced using different rubberised bitumens, including a Fischer–Tropsch wax pre-treated rubberised bitumen. Properties associated with rutting were evaluated using both linear and nonlinear viscoelastic analyses, using different test methods such as the Strategic Highway Research Programme (SHRP), Shenoy rutting parameter, zero shear viscosity (ZSV) and multiple stress creep recovery (MSCR) tests. The rutting resistance of the resulting SMA mixtures was assessed using the Repeated Load Axial Test (R…

BCD-01 JOINT INFLUENCE OF TRANSVERSE COMPRESSION AND SHEAR-FLEXURAL STIFFNESS ON RUBBER V-BELT MECHANICS(BELT AND CHAIN DRIVES)

2009

Solid State NMR Spectroscopy Investigation of the Molecular Structure of Epoxy Based Materials Cured in Different Conditions

2012

In this work two epoxy resin model systems, whose monomers are typically used in structural composites, were thermally cured in different cure conditions in order to obtain different cross-linking densities. Their molecular structures were investigated through solid state NMR spectroscopy in order to correlate them to the cure process conditions used and the results were discussed in the light of the dynamical mechanical thermal analysis (DMTA) performed.

Investigations on Load Capacity and stability of deformation of rubber cylindrical shells under internal pressure

1994

The paper presents a wide analysis of conditions under which a loss of deformation stability can be observed as well as local bulges form in axially-symmetric (rotational) shells of any length. Analytical relations of the theory of shells were used for the analysis. If the maximum pressure in the shell was exceeded, the deformation process was investigated too. In such a case, strains begin to develop more intensely in the central part of a long cylindrical shell and, owing to that, one or more superimposed bulges (blisters) form. Symmetry of the shell deformation in relation to the centre of its length can be disturbed. A set of algebraic equations was derived for determination of critical…