Search results for " Scanning"

Long-term performance of peat biofilters treating ethyl acetate, toluene, and its mixture in air.

2006

Three laboratory-scale peat biofilters were operated at 90 s empty bed residence time (EBRT) for over a year. Biodegradation of ethyl acetate, toluene, or a 1:1 mixture were investigated. In first stage, inlet concentration was progressively increased from 0.4 to 4.5 g/m3. The maximum elimination capacity (EC) found for ethyl acetate was 190 gC/m3·h, and it was not affected by toluene. The maximum EC found for toluene as a sole contaminant was 150 gC/m3·h, but the presence of ethyl acetate decreased the toluene maximum EC to 80 gC/m3·h. From respirometry monitoring, values of 3.19 g CO2/gC and 3.06 g CO2/gC for pure ethyl acetate and pure toluene, respectively, were found, with overall yiel…

Quantitative description of temperature induced self-aggregation thermograms determined by differential scanning calorimetry

2012

A novel thermodynamic approach for the description of differential scanning calorimetry (DSC) experiments on self-aggregating systems is derived and presented. The method is based on a mass action model where temperature dependence of aggregation numbers is considered. The validity of the model was confirmed by describing the aggregation behavior of poly(ethylene oxide)-poly(propylene oxide) block copolymers, which are well-known to exhibit a strong temperature dependence. The quantitative description of the thermograms could be performed without any discrepancy between calorimetric and van 't Hoff enthalpies, and moreover, the aggregation numbers obtained from the best fit of the DSC exper…

Competition between α and γ phases in isotactic polypropylene: effects of ethylene content and nucleating agents at different cooling rates

2001

Abstract The influence of ethylene content, nucleating agents and cooling rate upon the formation of γ phase in isotactic polypropylene is investigated. Detailed analysis of wide angle X-ray diffraction shows that some γ phase can appear even in copolymers of very low ethylene content (0.5 mol.%). Differential scanning calorimetry shows a double melting peak. Nucleating agents of different types are found to enhance γ phase crystallization, even in high molecular weight homopolymers. In any of the materials studied the amount of γ phase decreases with increasing cooling rate, going to zero at a cooling rate of about 10°C s−1. We interpret the observations in terms of the kinetics of growth …

The role of crystalline, mobile amorphous and rigid amorphous fractions in the performance of recycled poly (ethylene terephthalate) (PET)

2012

[EN] The action of thermo-mechanical degradation induced by mechanical recycling of poly(ethylene terephthalate) was simulated by successive injection moulding cycles. Degradation reactions provoked chain scissions and a reduction in molar mass mainly driven by the reduction of diethyleneglycol to ethylene glycol units in the flexible domain of the PET backbone, and the formation of -OH terminated species with shorter chain length. The consequent microstructural changes were quantified taking into account a three-fraction model involving crystalline, mobile amorphous (MAF) and rigid amorphous fractions (RAF). A remarkable increase of RAF, to a detriment of MAF was observed, while the percen…

Taking Advantage of Selective Change Driven Processing for 3D Scanning

2013

This article deals with the application of the principles of SCD (Selective Change Driven) vision to 3D laser scanning. Two experimental sets have been implemented: one with a classical CMOS (Complementary Metal-Oxide Semiconductor) sensor, and the other one with a recently developed CMOS SCD sensor for comparative purposes, both using the technique known as Active Triangulation. An SCD sensor only delivers the pixels that have changed most, ordered by the magnitude of their change since their last readout. The 3D scanning method is based on the systematic search through the entire image to detect pixels that exceed a certain threshold, showing the SCD approach to be ideal for this applicat…

EFFECT OF WATER ACTIVITY ON CRISPNESS OF BREAKFAST CEREALS

1991

Three breakfast cereals (two commercial products and one experimental product made by extrusion cooking) were placed over 10 saturated salt solutions in desiccators for 3 weeks and then studied by sensory and mechanical analysis. A slight decrease of sensory crispness intensity occurs between 0 and 0.50 (aw) or 7% (water content), after which there is a very rapid decrease. The value of critical water activity given by the intersection between the two straight lines which can be adjusted seems not to depend on the product. Moreover this value is confirmed by the mechanical analysis and, partially, by a Differential Scanning Calorimetry analysis. There is a good correlation between sensory c…

Integrating Domain Knowledge in Data-Driven Earth Observation With Process Convolutions

2022

The modelling of Earth observation data is a challenging problem, typically approached by either purely mechanistic or purely data-driven methods. Mechanistic models encode the domain knowledge and physical rules governing the system. Such models, however, need the correct specification of all interactions between variables in the problem and the appropriate parameterization is a challenge in itself. On the other hand, machine learning approaches are flexible data-driven tools, able to approximate arbitrarily complex functions, but lack interpretability and struggle when data is scarce or in extrapolation regimes. In this paper, we argue that hybrid learning schemes that combine both approa…

Template-Based Fabrication of Nanometer-Scaled Actuators from Liquid-Crystalline Elastomers

2010

Material properties of various intraocular lenses in an experimental study.

2002

<i>Introduction:</i> With the recent introduction of small-incision cataract surgery, requirements for intraocular lens (IOL) flexibility, strength and hydrophilicity have rapidly evolved. The IOL surface, however, remains a critical factor influencing uveal biocompatibility. <i>Purpose:</i> To objectively quantify factors of material properties of various IOLs using contact angle measurements, differential scanning calorimetry, dynamic-mechanical measurements and scanning electron microscopy. <i>Material and Methods:</i> In our study, 17 currently available IOLs were investigated using contact angle measurements to assess hydrophilicity and biocompatibil…

The coffee-machine bacteriome: biodiversity and colonisation of the wasted coffee tray leach

2015

AbstractMicrobial communities are ubiquitous in both natural and artificial environments. However, microbial diversity is usually reduced under strong selection pressures, such as those present in habitats rich in recalcitrant or toxic compounds displaying antimicrobial properties. Caffeine is a natural alkaloid present in coffee, tea and soft drinks with well-known antibacterial properties. Here we present the first systematic analysis of coffee machine-associated bacteria. We sampled the coffee waste reservoir of ten different Nespresso machines and conducted a dynamic monitoring of the colonization process in a new machine. Our results reveal the existence of a varied bacterial community…