Search results for " Shear"

Simplified analytical model for moment–axial force domain in the presence of shear in R.C. members externally strengthened with steel cages

2015

Equations for a hand calculation of moment–axial force domain in the presence of shear for R.C. beam/column externally strengthened with steel angles and strips are developed. The analytical derivation is made assuming, for axial load and flexure, the equivalent stress-block parameters for internal forces, considering the confinement effects induced in the concrete core by external cages both in the cases of strips or angles yielding. Limit states due to bond failure, concrete crushing and yielding of steel angles and strips in flexure and in shear, including moment-to-shear interaction, are considered. The proposed model gives results in a good agreement with available experimental data an…

Influence of variability and uncertainty of wind and waves on fatigue damage of a floating wind turbine drivetrain

2021

Abstract This study investigates the effect of variability and uncertainty of wind and wave conditions on the short-term fatigue damage of a 10-MW floating wind turbine drivetrain. Global dynamic responses of a semi-submersible wind turbine are calculated by aero-hydro-servo-elastic simulations in various environmental conditions. Then, rotor and generator loads, as well as nacelle motions from the global analysis are provided to a drivetrain model to investigate its dynamics. One-hour fatigue damage of the drivetrain bearings is calculated based on the bearing loads and speeds, and the effect of uncertainties related to wind and waves is assessed. The results indicate that the variations o…

Binder design of high RAP content hot and warm asphalt mixture wearing courses

2015

Reclaimed Asphalt Pavement (RAP) has shown great potential for being used in the construction or maintenance of roads. However, RAP is usually downgraded to lower pavement layers and the percentage of RAP used in wearing courses is still moderate (≤30%). The research and results contained in this paper focus on the definition of binder recipes aimed at increasing the percentage of RAP in hot and warm mix asphalt wearing courses. A review of current internationally used blend design methodologies is presented followed by case studies aimed at defining binder recipes for high RAP content asphalt mixture wearing courses to be further used for mix design and production in asphalt plants. Binder…

The transition from single layer to foliation boudinage: A dynamic modelling approach

2012

Abstract Foliation boudinage is a deflection of foliation in the vicinity of a central discontinuity in foliated rocks, mostly filled with vein material. It shows evidence for brittle deformation and void-opening during ductile flow. We used a two-dimensional visco-elastic spring model based on a discrete element approach to study the dynamic development of foliation boudinage and the behaviour of anisotropic visco-elastic material deformed under pure shear conditions. The anisotropies are set by defining rheological heterogeneities in the models with (1) a single layer in a weaker matrix; (2) multi-layers with different elastic properties and (3) random-distributed “micas”, rows of horizon…

Computational Modeling of Ascending Thoracic Aortic Aneurysm and Dissection

Sexing adult Cory's Shearwater by discriminant analysis of body measurements on Linosa Island (Sicilian Channel), Italy

2001

-Males and females of many avian species may show no plumage dimorphism, but often can be sexed by differences in body measurements. Sex determination of many Cory's Shearwaters Calonectris diomedea, was possible by multiplying bill length by bill depth. In this study, discriminant analysis of six measurements (bill length, bill depth, wing, tail, tarsus and mass) was performed on Cory's Shearwaters breeding on Linosa Island (Sicilian Channel), Italy and the efficiency of sex determination was compared with the univariate method. Results show the advantages of the discriminant functions. Bill depth is the best parameter (up to 92% correct classification), followed by mass (84% correct class…

Bond strength evaluation of the veneering-core ceramics bonds.

2009

The purpose of this study was to determine whether the bond of veneering porcelain to a ceramic core in bilayered ceramics was similar to that of the metal ceramic control of well known behaviour. Six groups of nine specimens each were fabricated, whose dimensions were 15 mm long and 8 mm in diameter at the core, and 2 mm long and 8 mm in diameter for the veneer. The groups were GR. 1 (control group): CrNi alloy/d.SIGN (Ivoclar), GR. 2: IPS e.maxPress/IPS e.maxCeram (Ivoclar), GR. 3: IPS e.maxZirCad/ IPS e.maxZirPress (Ivoclar), GR. 4: IPS e.maxZirCad/IPS e.maxCeram (Ivoclar), GR. 5: Lava Frame (3M ESPE)/ Lava Ceram (3M ESPE) and GR. 6: Lava Frame (3M ESPE)/IPS e.maxCeram (Ivoclar). A shear…

Generalized transport coefficients in a gas with large shear rate

1987

We get a solution of the Bhatnagar-Gross-Krook (BGK) model kinetic equation by means of a perturbative expansion of a temperature gradient to study the transport properties in a gas with large shear rate. The irreversible fluxes are evaluated exactly to first order in the expansion for Maxwell molecules. The transport coefficients obtained are highly nonlinear functions of the shear rate. This dependence on shear rate is analysed and compared with previous results for several transport coefficients. Finally, we have found a solution for a simple model of constant collision frequency for which a large shear rate coexists with an arbitrary temperature gradient.

Self-assembly and rheology of dipolar colloids in simple shear studied using multi-particle collision dynamics.

2017

Magnetic nanoparticles in a colloidal solution self-assemble in various aligned structures, which has a profound influence on the flow behavior. However, the precise role of the microstructure in the development of the rheological response has not been reliably quantified. We investigate the self-assembly of dipolar colloids in simple shear using hybrid molecular dynamics and multi-particle collision dynamics simulations with explicit coarse-grained hydrodynamics, conduct simulated rheometric studies and apply micromechanical models to produce master curves, showing evidence of the universality of the structural behavior governed by the competition between the bonding (dipolar) and erosive …

A critical assessment of methods for the determination of the shear stress amplitude in multiaxial fatigue criteria belonging to critical plane class

2015

Abstract Multiaxial high cycle fatigue criteria based on the critical plane approach necessitate unambiguous definitions of the amplitude and mean value of the shear stress (τa and τm) acting on the material planes. Four of the existing definitions relate the values of τa and τm to a geometrical element of the curve described by the tip of the shear stress vector (curve Ψ), respectively, the radius of the Minimum Circumscribed Circle, the Longest Chord, the Longest Projection, the diagonal of the Maximum Rectangular Hull (MRH). In this paper a critical assessment of the above definitions is proposed, focusing on that based on the concept of MRH, which is the most recently developed. The mai…