Search results for " Simulation"
showing 10 items of 4034 documents
Underwater Wireless Communications for Cooperative Robotics with UWSim-NET
2019
The increasing number of autonomous underwater vehicles (AUVs) cooperating in underwater operations has motivated the use of wireless communications. Their modeling can minimize the impact of their limited performance in real-time robotic interventions. However, robotic frameworks hardly ever consider the communications, and network simulators are not suitable for HIL experiments. In this work, the UWSim-NET is presented, an open source tool to simulate the impact of communications in underwater robotics. It gathers the benefits of NS3 in modeling communication networks with those of the underwater robot simulator (UWSim) and the robot operating system (ROS) in modeling robotic systems. Thi…
Simulation Goals and Metrics Identification
2016
Agent-Based Modeling and Simulation (ABMS) is a very useful means for producing high quality models during simulation studies. When ABMS is part of a methodological ap- proach it becomes important to have a method for identifying the objectives of the simulation study in a disciplined fashion. In this work we propose a set of guidelines for properly capturing and representing the goals of the simulations and the metrics, allowing and evaluating the achievement of a simulation objective. We take inspiration from the goal-question-metric approach and with the aid of a specific problem formalization we are able to derive the right questions for relating simulation goals and metrics.
A Comparison Study of a Novel Self-Contained Electro-Hydraulic Cylinder versus a Conventional Valve-Controlled Actuator—Part 1: Motion Control
2019
This research paper presents the first part of a comparative analysis of a novel self-contained electro-hydraulic cylinder with passive load-holding capability against a state of the art, valve-controlled actuation system that is typically used in load-carrying applications. The study is carried out on a single-boom crane with focus on the control design and motion performance analysis. First, a model-based design approach is carried out to derive the control parameters for both actuation systems using experimentally validated models. The linear analysis shows that the new drive system has higher gain margin, allowing a considerably more aggressive closed-loop position controller. Several b…
Generative Design for Additively Manufactured Textiles in Orthopaedic Applications
2021
AbstractThe aim of this work is to implement a new process for the design and production of orthopaedic devices to realize entirely by Additive Manufacturing (AM). In particular, a generative algorithm for parametric modelling of flexible structures to use in orthopaedic devices has been developed. The developed modelling algorithm has been applied to a case study based on the design and production of a customized elbow orthosis made by Selective Laser Sintering. The results obtained have demonstrated that the developed algorithm overcomes many drawbacks typical of traditional CAD modelling approaches. FEM simulations have been also performed to validate the design of the orthosis. The new …
Weld quality prediction in linear friction welding of AA6082-T6 through an integrated numerical tool
2016
Abstract A numerical and an experimental campaign were carried out with varying oscillation frequency and interface pressure. The local values of the main field variables at the contact interface between the specimens were predicted by a Lagrangian, implicit, thermo-mechanical FEM model and used as input of a dedicated Neural Network (NN). The NN, integrated in the FEM environment, was designed in order to calculate both a Boolean output, indicating the occurrence of welding, and a continuous output, indicating the quality of the obtained solid state weld. The analysis of the obtained results allowed three different levels of bonding quality, i.e., no weld, sound weld and excess of heat, to…
Springback of thick sheet AHSS subject to bending under tension
2012
Lien vers la version éditeur : http://www.sciencedirect.com/science/article/pii/S0020740312000677 The springback behavior of four advanced high-strength sheet steels (Dual-Phase, TRIP, ferrite-bainite) with thicknesses ranging from 1.2 to 4 mm was investigated by means of the bending-under-tension (BUT) test. The applicability of several guidelines from the literature was investigated experimentally and numerically. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for the non-linear influence of the tool radius was observed. The influence of numerical factors on the predicted values of springback was investigat…
Robust control for high performance induction motor drives based on partial state-feedback linearization
2019
This paper deals with a robust input-output feedback linearization control technique for induction motors. Indeed, classic feedback linearization presents two main disadvantages: 1) the accuracy of the dynamic model; and 2) the corresponding correct knowledge of the model parameters. To address this issue, the linear controller has been substituted with a suitably controller designed to be robust to the variations of the main parameters of the induction motor, like stator and rotor resistances, and the three-phase magnetizing inductance. The proposed controller has been tested both in numerical simulation and experimentally on a suitably designed test setup. Moreover, it has been compared w…
Enhancing tracking performance in a smartphone-based navigation system for visually impaired people
2016
In this paper we show how to enhance the tracking performance of Arianna, a low-cost augmented reality system designed to meet the needs of people with problems of orientation, people with sight impairment and blind people. For augmented reality system we mean the design of: i) a set of paths and tags to be deployed in the environment, realized in various ways depending on the context (decorative elements easily identifiable, colorful stripes, QR code, RFID, etc.); ii) an instrument of mediation between the reality and the user (typically a smartphone) to access the information disseminated in the environment by means of a camera and provide a vibration feedback signal to the users for foll…
Assessment of material models through simple machining tests
2008
The accuracy of the results obtained from FEM simulation of machining operations depends on the accuracy of input data. Among these, the flow stress data of the workpiece are extremely important together with the friction along the tool-chip interface. In this study, an identification procedure for the determination of material parameters that are used for the FEM simulation of machining processes is proposed. The procedure is based on the coupling of a numerical identification procedure and Arbitrarian Lagrangian Eulerian (ALE) Finite Element simulations of turning operations. An experimental campaign was developed in order to calibrate the model and to validate the procedure. The basic id…
Modelling and Simulation of Machining Processes and Operations
2008
This chapter provides the state-of-the-art knowledge engineering and modelling techniques applied in manufacturing/machining and overviews future trends observed at a global scale. Modelling methods for machining processes and operations are classified. The chapter also highlights the multiple tasks of modelling and simulation in modern machining/manufacturing systems. The most popular techniques of numerical simulation including finite difference method and finite element method (FEM) related to mechanical and thermal problems arising in machining processes are described. Practical examples of FE models of various metal cutting operations and their importance in modern manufacturing are pr…