Search results for " Spectroscopy"

Decorated pottery study: Analysis of pigments by x-ray absorbance spectroscopy measurements

2007

Characterization of pigments on decorated pottery fragments has been fully carried out by nondestructive x-ray absorbance spectroscopy (XAS). The samples were a series of pottery shards excavated from the archeological site of Caltagirone (Sicily, Italy), a well-known ceramic production center. Aesthetical criteria and morphological observations allowed us to attribute the samples to quite different historical periods, starting from the 18th century B.C. up to the 16th century A.D. An extensive time interval led us to suppose that different materials and techniques were used for the production of the ceramic paste and also for the preparation of pigments. XAS measurements were performed at …

Response of AGATA segmented HPGe detectors to gamma rays up to 15.1MeV

2013

WOS: 000314826000009

Fibrillation of Human Serum Albumin at physiological pH is inhibited by oxidation

2014

Corrosion and wear resistance of coatings produced on AZ31 Mg alloy by plasma electrolytic oxidation in silicate-based K2TiF6 containing solution: Ef…

2022

Abstract In this research, plasma electrolytic oxidation coatings were prepared on AZ31 Mg alloy in a silicate-based solution containing K2TiF6 using bipolar and soft sparking waveforms with 10, 20, and 30% cathodic duty cycles. The coatings displayed a net-like surface morphology consisted of irregular micro-pores, micro-cracks, fused oxide particles, and a sintered structure. Due to the incorporation of TiO2 colloidal particles and the cathodic pulse repair effect, most of the micro-pores were sealed. Long-term corrosion performance of the coatings was investigated using electrochemical impedance spectroscopy during immersion in 3.5 wt.% NaCl solution up to 14 days. The coating grown by t…

Study of the electronic and atomic structure of thermally treated SrTiO3(110) surfaces

2003

The electronic structure of heated SrTiO3(110) surfaces was investigated with metastable impact electron spectroscopy and ultraviolet photoelectron spectroscopy (He(I). Scanning tunnelling microscopy and atomic force microscopy (AFM) were used to study the topology of the surface. The crystals were heated up to 1000 °C under reducing conditions in ultrahigh vacuum or under oxidizing conditions in synthetic air for 1 h, respectively. Under both conditions microfacetting of the surface is observed. The experimental results are compared with ab initio Hartree-Fock calculations, also presented here, carried out for both ideal and reconstructed SrTiO 3(110) surfaces. The results give direct evid…

Analysis of the morphology and composition of tooth apices apicectomized using three different ablation techniques.

2011

Objectives: To investigate apicectomies performed using burs, a CO2 laser or an Er:YAG laser and to evaluate the following aspects: morphology of apicectomized surfaces, presence of failures at the dentin/obturation material interface (marginal fit) of the apical portions of the root canals, and the proportions of chemical elements in the apicectomized surfaces. Study design: Twenty-four teeth were divided into three groups of eight and each group underwent apicectomy by one of three different ablation techniques: bur, CO2 laser or Er:YAG laser. The morphology of the apicectomized surfaces was then analyzed using scanning electron microscopy and their chemical composition was analyzed by en…

<title>Hardening in LiF, induced by fast Kr and Ni ions, and recovery of the structure and properties under annealing</title>

2005

The recovery of optical and mechanical properties of LiF crystals irradiated with 790 MeV 78Kr and 640 MeV 58Ni ions at 10l2 ions/cm2 under annealing at temperatures up to 810 K is investigated. The optical absorbance and depth profiles of hardness before and after annealing were measured. A marked recovery of hardness and change in the optical absorption spectra were observed at temperatures above 520-530 K. An activation energy of 0.15±0.02eV, which is close to that for the thermal migration of H centers, is obtained from the annealing data. The results indicate a significant role of the H-center aggregates in the hardening and annealing processes. The maximum hardening is created and the…

Solid sampling Fourier transform infrared determination of Mancozeb in pesticide formulations

2004

Abstract A series of approaches have been assayed for FTIR determination of Mancozeb in several solid commercial fungicides using different calibration strategies. The simplest procedure was based on the use of the ratio between the absorbance of a characteristic band of Mancozeb and that of a KSCN internal standard measured in the FTIR spectra obtained from KBr pellets. It was employed the quotient between peak height absorbance values at 1525 cm−1 for Mancozeb and 2070 cm−1 for KSCN. In these conditions a precision as relative standard deviation (RSD) of 0.6% and a relative accuracy error of 0.8% (w/w) were found. For complex formulations, containing other compounds with characteristic ab…

Utilization of impedance spectroscopy to investigate the self-assembly behavior of amphiphiles soluble in supercritical carbon dioxide: Preliminary r…

2007

Abstract A mixture of CO 2 , water, methyl orange (MO) and Dynol 604 surfactant was analyzed at 309 K and 20 MPa simultaneously by impedance and UV–vis spectroscopy. A plot of the static dielectric constant as a function of the surfactant concentration was obtained using a suitable equivalent circuit to elaborate impedance data. Experimental points can be fitted by two different straight lines whose intersection occurs at about 0.13% (w/w) concentration of Dynol. When the surfactant concentration crossed the aforementioned value, a peak was detectable in the UV–vis spectrum at a wavelength range corresponding to the absorption of MO; absorbance of the peak increased with the surfactant conc…

FTIR quantitative analysis of calcium carbonate (calcite) and silica (quartz) mixtures using the constant ratio method. Application to geological sam…

2002

A methodology for quantifying calcium carbonate (875 and 712 cm(-1)) and silica (798 and 779 cm(-1)) by FTIR spectroscopy applying the constant ratio method is proposed. The studied method is applied for quantitative analysis of calcite and quartz in geological samples. The suggested method uses potassium ferricyanide (2115 cm(-1)) as standard and samples are prepared as potassium bromide pellets, with statistically satisfactory results (relative standard deviation less than 5%). The influence of particle size (pulverised samples) on the accuracy of the results found by FTIR spectroscopy applying the constant ratio method has been studied. The granulometric study suggests that the homogenei…