Search results for " Steel"
showing 10 items of 244 documents
Composite layer-based analytical models for tool–chip interface temperatures in machining medium carbon steels with multi-layer coated cutting tools
2006
Abstract This investigation is devoted to the thermal problems in dry orthogonal turning of a C45 medium carbon steel with natural contact tools treated with multi-layer coatings with an intermediate Al 2 O 3 layer. New hybrid analytical models for estimating heat partition to the chip and the tool–chip interface temperatures were proposed. Furthermore, the physics-based modelling concept, which applies composite layer approach was developed to estimate the average and maximum steady-state tool–chip interface temperatures in orthogonal turning. The model predictions were compared to appropriate experimental process data using natural tool-work thermocouples and other simulated and measured …
The effect of wear on the tetragonal-to-monoclinic transformation and the residual stress distribution in zirconia-toughened alumina cutting tools
1998
Abstract Zirconia-toughened alumina cutting tools have been examined after machining an AISI 1040 steel. The Raman spectrum of zirconia and the fluorescence spectrum from alumina have been used to determine the extent of the tetragonal-to-monoclinic (t-m) transformation and the residual stresses in and around the worn-out crater, respectively. Although about 15% vol. m-zirconia is present even in a brand new cutting tool, it was shown that the crater region undergoes the t-m transformation up to 40% vol. In both cases, the transformed zone is concentrated near the surface. The residual stresses in alumina are slightly compressive in the new cutting tool and away from the crater region, but …
Use of FRP fabrics and stainless steel grids for strengthening brick masonry columns
2016
This work presents the results of an experimental investigation on 42 solid clay brick columns internally strengthened by FRP fabrics or stainless steel grids placed in the horizontal joints of mortar. Monotonic compressive loading tests were carried out under concentric and eccentric load. Eccentric tests were carried out loading the specimens on a reduced area with respect to the entire crosssection producing a D-region. The reinforcing of every course and of alternate courses are studied. The effectiveness of the proposed strengthening techniques is discussed, in terms of increase in strength and energy required to the collapse of brick columns. An analytical expression is proposed that …
Behaviour in compression of lightweight fiber reinforced concrete confined with transverse steel reinforcement
2004
Abstract The compressive behavior of lightweight fiber reinforced concrete confined with transverse reinforcement consisting of steel stirrups or spirals was analyzed. Pumice stone and expanded clay aggregates were utilized to decrease the weight of the composite; hooked steel fibers were also added. The investigation was carried out by testing cylindrical and prismatic specimens of different sizes in compression using an open-loop displacement control machine, recording the full load–deformation curves. The influence of the dimensions and shape on the bearing capacity and on the ductility of the specimens confined with transverse steel reinforcements was analyzed. The results show the poss…
Steel fiber-reinforced concrete corbels:experimental behavior and shear strength prediction
2007
Corbels are structural members often used in reinforced concrete structures to transfer vertical and horizontal forces to principal members. This paper presents experimental research regarding the flexural behavior of corbels in plain and fibrous concrete and in the presence of steel bars. The study considers the influence of the type of concrete grade (normal- and high-strength concretes), of the fiber percentage and of the arrangement and percentage of the steel bars on the flexural behavior of the corbels. The results in terms of load-deflection curves and crack patterns show the effectiveness in using fibrous reinforced concrete corbels as well as in the presence of stirrups ensuring ad…
Parametric study of laser welding of copper to austenitic stainless steel
2018
Abstract Welding of copper to stainless steel is challenging because of sharp difference in thermophysical properties of materials and the presence of miscibility gap in Fe-Cu system. The parametric study of continuous Yb:YAG laser welding between copper and austenitic stainless steel 316L has been performed. The influence of laser power, welding speed and beam offset from joint line on weld composition, microstructure and tensile properties was studied. The corrosion behaviour of the welds was evaluated in 0.1M NaCl with the potentiostatic pulse testing method, salt fog and immersion tests. In function of copper dilution in the melted zone, different types of microstructure were observed: …
Structural Behavior of Telescopic Steel Pipe for a Full-Scale 60 kW Wind Turbine Tower
2020
A simple analytical model, including local effects due to buckling and shear to moment interaction, was developed to pre-dict the load-carrying capacity of CHS tubes under flexure and shear. A finite-element analysis with ABAQUS Code was also conducted for validation of the proposed model. By properly modeling the imperfection effects due to the ovalization of steel tube, a good correlation of the structural response and failure mode was also achieved, and a good correlation with the analytical model was also achieved. Numerical and analytical results were compared with experimental results recently obtained by the author with good agreement. Experimental tests refer to full-scale static te…
Mechanical and cohesion properties of brass plated steel cords in a sulphurizing environment
1986
The mechanical and cohesion properties of brass plated steel cords have been investigated in dry hydrogen sulphide between 25 and 450° C. The extents of elastic and plastic regions, obtained from slow strain rate technique data have been defined, and the preferential site of decohesion tends to be the brass-steel interface.
Interactions in dual species biofilms between Listeria monocytogenes EGD-e and several strains of Staphylococcus aureus.
2008
International audience; Six environmental isolates of Staphylococcus aureus and one collection strain were investigated for their ability to form monospecies biofilms and dual species biofilms with Listeria monocytogenes EGD-e on stainless steel coupons. All isolates were able to grow as biofilms but their ability to form monospecies biofilms differed. The population of L. monocytogenes EGD-e in dual species biofilms was not affected by the presence of S. aureus isolates except for strain CIP 53.156. The effect of L. monocytogenes EGD-e on the population of S. aureus was strain dependent: S. aureus population either increased or decreased or was not affected in the presence of L. monocytoge…
Role of Molybdenum on the Electronic Properties of Passive Films on Stainless Steels
2020
Potentiostatic polarization of different stainless steel grades with a mirror surface finishing was performed in order to investigate the role of Mo on stainless steels corrosion behaviour. In the attempt to gain more insight into transpassive dissolution mechanism, passive films were grown in neutral aqueous solution (pH ∼ 7) at different polarizing potentials ranging from passive to transpassive conditions. According to the photoelectrochemical characterization, Cr dissolution occurs even at low polarizing potentials in the case of AISI 304L, while higher band gap values were obtained for passive films grown on austenitic 316L and duplex SSs. Capacitance measurements suggest that the flat…