Search results for " Structural"
showing 10 items of 1751 documents
Biodynamic behavior of the trunk and the abdomen during whole-body vibration
1989
Vibration strain may be defined as the sum of all reactions of the human being to vibration exposure. This also includes the biomechanical behavior of particular parts of the body. Knowledge about these reactions is necessary in the field of occupational health and ergonomics. Biomechanical models, experimental methods, and results are presented. It can be shown that under vibration exposure with different conditions (body posture, vibration direction), the body parts are in resonance at varying frequencies, mainly in a low frequency range.
Convolution-based ensemble learning algorithms to estimate the bond strength of the corroded reinforced concrete
2022
Reinforced concrete bond strength deterioration is one of the most serious problems in the construction industry. It is one of the most common factors impacting structural deterioration and the major cause of premature decadence of reinforced concrete structures. Therefore, developing an accurate model with the lowest variance and high reliability for the bond strength of corroded reinforced concrete is very important. The current work evaluates the efficiency of convolution-based ensemble learning algorithms. To address these issues, convolution-based ensemble learning models are developed using a database collected from the previous experimental studies of relative bond strength for corro…
Steel-concrete bond in lightweight fiber reinforced concrete under monotonic and cyclic actions
2005
Experimental results of the local bond stress-slip relationship of reinforcing bars embedded in lightweight fiber reinforced concrete with expanded clay aggregates are presented. The effect of the following parameters were investigated: - dimension of specimens; - anchorage length; - percentages of hooked steel fibers; - geometrical ratio of transverse reinforcement; - confinement external transverse pressure. Prismatic specimens with deformed steel bars embedded for a fixed length equal to five and eight equivalent diameters were tested under both monotonic and cyclic reversal imposed displacements at the tip of the bars, in controlled displacement tests. The influence of the above mention…
Application of dual boundary element method in active sensing
2013
In this paper, a boundary element method (BEM) for the dynamic analysis of 3D solid structures with bonded piezoelectric transducers is presented. The host structure is modelled with BEM and the piezoelectric transducers are formulated using a 3D semi-analytical finite element approach. The elastodynamic analysis of the entire structure is carried out in Laplace domain and the response in time domain is obtained by inverse Laplace transform. The BEM is validated against established finite element method (FEM).
Tsunami Vulnerability Evaluation for a Small Ancient Village on Eastern Sicily Coast
2022
The Ionian sea is prone to tsunamis due to its proximity to the Calabrian subduction zone, which is one of the major tsunamigenic areas of the Mediterranean. The tsunami disaster risk is, nowadays, significantly higher due to the increased exposure of buildings as a result of the economic and touristic growth of the Mediterranean coastal areas. This study focuses on Marzamemi, a small village in the western coast of Sicily, since its morphology and human presence amplify the need to assess its buildings’ vulnerability. The main objective of this research is to quantify the building vulnerability to tsunami hazards using a physical and realistic tsunami scenario. For this purpose, the relati…
Recent progress in developing a feasible and integrated conceptual design of the WCLL BB in EUROfusion project
2019
The water-cooled lithium-lead breeding blanket is in the pre-conceptual design phase. It is a candidate option for European DEMO nuclear fusion reactor. This breeding blanket concept relies on the liquid lithium-lead as breeder-multiplier, pressurized water as coolant and EUROFER as structural material. Current design is based on DEMO 2017 specifications. Two separate water systems are in charge of cooling the first wall and the breeding zone: thermo-dynamic cycle is 295–328 °C at 15.5 MPa. The breeder enters and exits from the breeding zone at 330 °C. Cornerstones of the design are the single module segment approach and the water manifold between the breeding blanket box and the back suppo…
Use of fiber-section beam elements for modelling the monotonic flexural response of RC jacketed columns
2021
Abstract The use of reinforced concrete (RC) jacketing is a common technique for retrofitting existing RC columns with poor structural performances. Literature studies highlighted that the relative slip occurring at the interface between the new and the old concrete can affect substantially the flexibility and the strength of the retrofitted member. For this reason, several interface treatments are usually applied, aiming to induce a monolithic behaviour to the column. However, despite the commonness of RC jacketing, a limited number of studies investigated numerical modelling strategies for including these phenomena, especially with reference to the development of numerical models for desi…
Lit environments quality: A software for the analysis of luminance maps obtained with the HDR imaging technique
2013
Abstract Energy performance of lighting systems has assumed a significant role in the assessment of buildings’ consumptions and consequently lighting design is aimed to reduce installed power but at the same time to achieve an excellent lighting quality both for visual and health purposes. Lighting design is nowadays essentially based on illuminance values on visual tasks and surrounding areas, but today designers’ and researchers’ interest is focused on the analysis of luminance maps obtained through video luminance meters or with numeric simulation tools. Luminance maps availability focus the attention on a more accurate study of the light reaching the eyes (luminance), rather than on the…
Effect of operating conditions and feedstock composition on the properties of manganese oxide or quartz charcoal pellets for the use in ferroalloy in…
2020
peer-reviewed The full text of this article will not be available until the embargo expires on the 26/12/2021 This study investigates the effect of heat treatment temperature on the properties of charcoal composite pellets used for the reduction of ferroalloys. The heavy fraction of biooil was used as a binder for the charcoal ore pellet preparation. The effect of heat treatment temperature on the pellet shrinkage was related to the degree of reduction which varied with feedstock and ore composition. The results showed that the size and shape of the charcoal pellets were not affected by the biooil devolatilization. Manganese charcoal pellets showed higher electrical resistance during pyroly…
Combination of ozonation and photocatalysis for purification of aqueous effluents containing formic acid as probe pollutant and bromide ion
2014
The treatment by advanced oxidation processes (AOPs) of waters contaminated by organic pollutants and containing also innocuous bromide ions may generate bromate ions as a co-product. In the present work heterogeneous photocatalysis and ozonation have individually been applied and in combination (integrated process) to degrade the organic compounds in water containing also bromide anions. The results show that: i) the sole photocatalysis does not produce bromate ions and in the case of its presence, it is able to reduce bromate to innocuous bromide ions; ii) the integration of photocatalysis and ozonation synergistically enhances the oxidation capabilities; and iii) in the integrated proces…