Search results for " Structural"

Discussion of "extraction of the flow rate equation under free and submerged flow conditions in pivot weirs with different side contractions" by N. S…

2018

This paper is the discusison of the paper "Extraction of the flow rate equation under free and submerged flow conditions in pivot weirs with different side contractions" by N. Sheikh Rezazadeh Nikou, M. J. Monem, and K. Safavi.

Closure to “Extraction of the Flow Rate Equation under Free and Submerged Flow Conditions in Pivot Weirs with Different Side Contractions” by N. Shei…

2018

Cross-correlation of whitened vibration signals for low-speed bearing diagnostics

2019

Abstract Rolling-element bearings are crucial components in all rotating machinery, and their failure will initially degrade the machine performance, and later cause complete shutdown. The period between an initial crack and complete failure is short due to crack propagation. Therefore, early fault detection is important to avoid unexpected machine shutdown and to aid in maintenance scheduling. Bearing condition monitoring has been applied for several decades to detect incipient faults at an early stage. However, low-speed conditions pose a challenge for bearing fault diagnosis due to low fault impact energy. To reliably detect bearing faults at an early stage, a new method termed Whitened …

Integrated GNSS/IMU Hub Motion Estimator for Offshore Wind Turbine Blade Installation

2019

Abstract Offshore wind turbines (OWTs) have become increasingly popular for their ability to harvest clean offshore wind energy. Bottom-fixed foundations are the most used foundation type. Because of its large diameter, the foundation is sensitive to wave loads. For typical manually assisted blade-mating operations, the decision to perform the mating operation is based on the relative distance and velocity between the blade root center and the hub, and in accordance with the weather window. Hence, monitoring the hub real-time position and velocity is necessary, whether the blade installation is conducted manually or automatically. In this study, we design a hub motion estimation algorithm f…

Autonomous ultrasonic inspection using Bayesian optimisation and robust outlier analysis

2020

The use of robotics is beginning to play a key role in automating the data collection process in Non Destructive Testing (NDT). Increasing the use of automation quickly leads to the gathering of large quantities of data, which makes it inefficient, perhaps even infeasible, for a human to parse the information contained in them. This paper presents a solution to this problem by making the process of NDT data acquisition an autonomous one as opposed to an automatic one. In order to achieve this, the robotic data acquisition task is treated as an optimisation problem, where one seeks to find locations with the highest indication of damage. The resulting algorithm combines damage detection tech…

Vibration Control of a High-Speed Precision Servo Numerically Controlled Punching Press: Multidomain Simulation and Experiments

2017

A three-degree-of-freedom mathematical vibration model of a high-speed punching press was developed in order to explore the vibration modes of the punching press. A multidomain model of the punching press was established to predict the kinematic state during different conditions, as well as the effects of load fluctuation on the motor speed. Experimental measurements of the acceleration of the punching press were carried out. The results comparison reveals that the multidomain model is consistent with the vibration model and the experimental measurements. Modal analysis and structure modification of the punching press were conducted. The foundation at the base of the punching press was impr…

Springback of thick sheet AHSS subject to bending under tension

2012

Lien vers la version éditeur : http://www.sciencedirect.com/science/article/pii/S0020740312000677 The springback behavior of four advanced high-strength sheet steels (Dual-Phase, TRIP, ferrite-bainite) with thicknesses ranging from 1.2 to 4 mm was investigated by means of the bending-under-tension (BUT) test. The applicability of several guidelines from the literature was investigated experimentally and numerically. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for the non-linear influence of the tool radius was observed. The influence of numerical factors on the predicted values of springback was investigat…

Effect of the mutual position between weld seam and reinforcement on the residual stress distribution in Friction Stir Welding of AA6082 skin and str…

2016

Abstract In the paper, a numerical and experimental study was carried out to highlight the effect of the distance d between the weld seam and the reinforcement on the residual stress distribution in Friction Stir Welded AA6082-T6 structures. An L-shaped profile was welded to a sheet metal with varying tool rotation and distance d from the weld seam. The Cut Compliance method was used to determine the resulting longitudinal residual stress. A dedicated FE model for FSW was set up, validated and utilized to predict the longitudinal residual stress in the assembled part. The analysis allowed the identification of a few design guidelines in order to reduce the detrimental effects of the residua…

Vibration reduction on city buses: Determination of optimal position of engine mounts

2010

International audience; This study is composed of three essential parts. The first part describes an indirect semi-experimental method which is used to reconstruct the excitation force of an operating diesel engine from the acceleration data measured at the mounting points. These internal forces can not be directly measured with force sensors; they have to be derived from the dynamic deformation of the engine support, so a theoretical analysis is carried out to derive the equations for the force re-construction.The second part deals with prevention of low frequency vibration of the powertrain from spreading to the rest of the vehicle. Three uncoupling techniques are used to minimize these v…

Multi-band identification for enhancing bearing fault detection in variable speed conditions

2020

Abstract Rolling element bearings are crucial components in rotating machinery, and avoiding unexpected breakdowns using fault detection methods is an increased demand in industry today. Variable speed conditions render a challenge for vibration-based fault diagnosis due to the non-stationary impact frequency. Computed order tracking transforms the vibration signal from time domain to the shaft-angle domain, allowing order analysis with the envelope spectrum. To enhance fault detection, the bearing resonance frequency region is isolated in the raw signal prior to order tracking. Identification of this region is not trivial but may be estimated using kurtosis-based methods reported in the li…