Search results for " acoustic"

Noise characterization of analog to digital converters for amplitude and phase noise measurements

2017

International audience; Improvements on electronic technology in recent years have allowed the application of digital techniques in phase noise metrology where low noise and high accuracy are required, yielding flexibility in systems implementation and setup. This results in measurement systems with extended capabilities, additional functionalities and ease of use. In most digital schemes the Analog to Digital Converters (ADCs) set the ultimate performance of the system, therefore the proper selection of this component is a critical issue. Currently, the information available in literature describes in depth the ADC features only at frequency offsets far from the carrier. However, the perfo…

Equivalence of Open-Loop and Closed-Loop Operation of SAW Resonators and Delay Lines

2019

International audience; Surface acoustic wave (SAW) sensors in the form of two-port resonators or delay lines are widely used in various fields of application. The readout of such sensors is achieved by electronic systems operating either in an open-loop or in a closed-loop configuration. The mode of operation of the sensor system is usually chosen based on requirements like, e.g., bandwidth, dynamic range, linearity, costs, and immunity against environmental influences. Because the limit of detection (LOD) at the output of a sensor system is often one of the most important figures of merit, both readout structures, i.e., open-loop and closed-loop systems, are analyzed in terms of the minim…

Phase-Noise and Amplitude-Noise Measurement of DACs and DDSs

2019

This article proposes a method for the measurement of Phase Noise (PN, or PM noise) and Amplitude Noise (AN, or AM noise) of Digital-to-Analog Converters (DAC) and Direct Digital Synthesizers (DDS) based on modulation-index amplification. The carrier is first reduced by a controlled amount (30-40 dB) by adding a reference signal of nearly equal amplitude and opposite in phase. Then, residual carrier and noise sidebands are amplified and sent to a conventional PN analyzer. The main virtues of our method are: (i) the noise specs of the PN analyzer are relaxed by a factor equal to the carrier suppression ratio; and, (ii) the capability to measure the AN using a PN analyzer, with no need for th…

Frequency Stability Measurement of Cryogenic Sapphire Oscillators with a Multichannel Tracking DDS and the Two-Sample Covariance

2018

This article shows the first measurement of three 100 MHz signals exhibiting fluctuations from 2E-16 to parts in 1E-15 for integration time tau between 1 s and 1 day. Such stable signals are provided by three Cryogenic Sapphire Oscillators (CSOs) operating at about 10 GHz, also delivering the 100 MHz output via a dedicated synthesizer. The measurement is made possible by a 6-channel Tracking DDS (TDDS) and the two-sample covariance tool, used to estimate the Allan variance. The use of two TDDS channels per CSO enables high rejection of the instrument background noise. The covariance outperforms the Three-Cornered Hat (TCH) method in that the background converges to zero "out of the box," wi…

Prediction of hydraulic and acoustic properties of open-graded mixes

2014

The use of open-graded mixes increases significantly the hydraulic permeability of pavement and contributes to reduce the noise impact in comparison to traditional pavement. Such characteristics are very appealing and would greatly increase driver's safety. However, during service life, the pores tend to be clogged by many factors among them secondary traffic compaction and filling of voids by fine materials are relevant, especially on heavy routes. In this case the noise reduction and drainage capabilities will gradually disappear, causing serious problems for road safety and maintenance. In this paper we propose a simulation approach in order to predict the drainage and acoustic behavior …

Estimates for Divergence Velocities of Axially Moving Orthotropic Thin Plates

2014

Some models for axially moving orthotropic thin plates are investigated analytically via methods of complex analysis to derive estimates for critical plate velocities. Linearised Kirchhoff plate theory is used, and the energy forms of steady-state models are considered with homogeneous and inhomogeneous tension profiles in the cross direction of the plate. With the help of the energy forms, some limits for the divergence velocity of the plate are found analytically. In numerical examples, the derived lower limits for the divergence velocity are analysed for plates with small flexural rigidity. peerReviewed

Front Cover: Magnetic Bistability in Macrocycle‐Based Fe II Spin‐Crossover Complexes: Counter Ion and Solvent Effects (Eur. J. Inorg. Chem. 34/2016)

2016

Digital signal processing applied to noisy acoustic data.

2007

Frequently we deal with analog data from noisy acoustic measurements which need a preprocessing prior to the extraction of the information embedded. Data deterioration may be due to several reasons, for example: data recording on obsolete and technological poor support; bad signal conditioning (poor signal-to-noise ratio, non linearity and/or timevariance of the system under test). Sometimes information to be extracted from data is not conventional so it needs a dedicated processing. In this paper a novel audio data processing method from the autors experience in ancient open-air theatres research is shown.

Prospectives to tractor cabin design with computational acoustics tools

2011

Computational acoustical models allow automated optimization of tractor design with respect to acoustic properties, which could speed up significantly the design process of tractor cabin prototypes. This article gives insightful prospectives to the tractor design process by considering modern computational acoustics technology. Mathematical formulation for a system consisting of vibrating elastic tractor structure and airfilled acoustic enclosure are given and a related numerical solution technique with finite element method (FEM) is presented. Simulation results produced with commercially available software are reviewed. nonPeerReviewed

FLUMO: FLexible Underwater MOdem

2019

The last years have seen a growing interest in underwater acoustic communications because of its applications in marine research, oceanography, marine commercial operations, the offshore oil industry and defense. High-speed communication in the underwater acoustic channel has been challenging because of limited bandwidth, extended multipath, refractive properties of the medium, severe fading, rapid time variation and large Doppler shifts. In this paper, we show an implementation of a flexible Software-Defined Acoustic (SDA) underwater modem, where modulation parameters are completely tunable to optimize performance. In particular, we develop the system architecture following two key ideas. …