Search results for " array"

Commissioning Experience with the ATLAS Level-1 Calorimeter Trigger System

2007

The ATLAS Level-1 Calorimeter Trigger is one of the main elements of the first stage of event selection for the ATLAS experiment at the LHC. The input stage consists of a mixed analogue/digital component taking trigger sums from the ATLAS calorimeters. The trigger logic is performed in a digital, pipelined system with several stages of processing, largely based on FPGAs, which perform programmable algorithms in parallel with a fixed latency to process about 300 Gbyte/s of input data. The real-time output consists of counts of different types of physics objects and energy sums. The production of final modules started in 2006, and installation of these modules and the necessary infrastructure…

Spectral Characterization of a Prototype SFA Camera for Joint Visible and NIR Acquisition

2016

International audience; Multispectral acquisition improves machine vision since it permits capturing more information on object surface properties than color imaging. The concept of spectral filter arrays has been developed recently and allows multispectral single shot acquisition with a compact camera design. Due to filter manufacturing difficulties, there was, up to recently, no system available for a large span of spectrum, i.e., visible and Near Infra-Red acquisition. This article presents the achievement of a prototype of camera that captures seven visible and one near infra-red bands on the same sensor chip. A calibration is proposed to characterize the sensor, and images are captured…

Photovoltaic plant array reconfiguration: Design of a new device

2014

An efficient strategy to improve unequally irradiated PV plants performances is based on the reconfiguration of the connections between the modules. In this paper, an algorithm, for this purpose conceived, is presented. Moreover, the design, realization and finally also the set up of a new reconfiguration system device is fully shown and discussed. The algorithm conceived simulates several possible series-parallel connections under varying irradiation conditions, and determines the optimal modules connection in order to get the maximum output power. In this way, the reconfiguration system may set up the reconfiguration strategy. The reconfiguration system prototype set up, basically consist…

Design and control of a novel multi-source renewable energy system

2014

In this paper, a novel multi-input, single-inductor architecture is proposed. An innovative hysteretic control strategy of both the output voltage and the sources operating point control is designed and tested. Benefits brought by the proposed architecture over existing solutions are widely investigated. As an example, the design of a 48 V dual input system which is fed by photovoltaic and thermo-electric generators is proposed. Design guidelines are given and simulation results are presented to test the efficiency of the proposed architecture.

<title>Control and measuring buses with amplitude fiber optical sensors</title>

2004

This paper presents controlling-measuring buses (linear and quasi-linear) using amplitude properties of fiber-optics and fiber-optical sensors of typical and/or special construction. It refers to linear sensors and commonly used measuring OTDR method, as wel as to realizations with linear binary sensors in transmission networks. Presented advantages and parameters of such measuring structures. Presented main area of application buses and practical realizations, regarding typical needs in industrial measurements, points out technical and economical advantages, in opposition to difficult and expensive (but more accurate) technology of measuring networks based on polarization and interfering m…

Technical and economical evaluation on the use of reconfiguration systems in some EU countries for PV plants

2017

This paper shows the technical and economical evaluation of the application of a reconfiguration system for photovoltaic (PV) plants, considering the incentives system in some European Union countries. The reconfiguration system is an alternative to the distributed maximum power point tracking technique which used to increase the power production in the PV plants under the mismatch phenomenon. The reconfiguration techniques employ a microprocessor-based or field-programmable gate array-based system that modifies the layout of the PV plant through the change of the connections among modules. After having presented the main features working of the PV reconfiguration system allowing the improv…

An FPGA-Based Software Defined Radio Platform for the 2.4GHz ISM Band

2006

A prototype of a Software Defined Radio (SDR) platform has been successfully designed and tested implementing a reconfigurable IEEE 802.11 and ZigBee receiver. The system exploits the reconfiguration capability of an FPGA for implementing a number of receiver configurations that share the same RF front-end. Configurations can be switched at run time, or can share the available logic and radio resource.

A simple and accurate model of photovoltaic modules for power system design

2014

Obtaining dynamic Norton parameters of a solar panel from manufacturer data

2016

Photovoltaic arrays have been shown to possess significant influence on the dynamic performance of coupled source-converter-load system while its dynamic resistance is the most important parameter, contributing to the overall system dynamics. In this paper, a method of deriving the parameters of linearized photovoltaic equivalent circuit from manufacturer data is proposed. The approach allows predicting the range of dynamic Norton parameters for the expected irradiation and temperature operation conditions thus defining clear bounds required for robust design of the system controller.

Electronic noses: a review of signal processing techniques

1999

The field of electronic noses, electronic instruments capable of mimicking the human olfactory system, has developed rapidly in the past ten years. There are now at least 25 research groups working in this area and more than ten companies have developed commercial instruments, which are mainly employed in the food and cosmetics industries. Most of the work published to date, and commercial applications, relate to the use of well established static pattern analysis techniques, such as principal components analysis, discriminant function analysis, cluster analysis and multilayer perceptron based neural networks. The authors first review static techniques that have been applied to the steady-s…