Search results for " costruzione."
showing 10 items of 477 documents
Performances Comparison for a Rotating Shaft Suspended by 4-Axis Radial Active Magnetic Bearings via 𝜇 -Synthesis, Loop-Shaping Design, and Sub ( 𝐻…
2011
The control systems applied on active magnetic bearing are several. A perfect levitation is characterized by maintaining the operating point condition that is characterized by the center of stator coincident with the geometric center of shaft. The first controller implemented for this purpose is PID controller that is characterized by an algorithm that leads the amplifier to produce control current until the operating point condition is not reached, this is obtained by an integration operator. The effect of an integrator is essential but not necessary for a centered levitation for example in the robust control characterized by a dynamic model depended on plant of system so that it depends o…
Analysis of the accuracy of fiber-optic strain transducers installed by using composite smart patches
2015
The aim of this work is to investigate the accuracy of fiber-optic strain transducer related to the incomplete load transmission that can occur on composite smart patches used as base support for the installation of such transducer, commonly used for structural monitoring of concrete elements. In detail, since the dimensions of the transducer are generally very small compared to those of the structural element being monitored, attention is given not to the global reinforcement effect, which occurs when the transducer alters the entire strain field of the transversal section of the monitored element, but rather to the so-called local reinforcement effect, which is due to an incomplete load …
Finite Element Simulation of Multilayer Metal Cylinder Head Gaskets
2006
ABAQUS gasket elements are an efficient and flexible tool to study gasket applications. Nevertheless the usage of the ABAQUS gasket elements is not limited to gasket analysis, but it provides an effective improvement in structural analysis. The results point out that both the predicted contact pressure and the predicted stress distribution depend on the mesh topology. Several combinations of mesh dimension and topology are investigated. The purpose is the definition of a calculation methodology and the demonstration of the application potentiality. Complex models analysis highlights that the set methodology constitutes a very effective tool for the design and optimization of gasket, cylinde…
Error and Uncertainty Analysis of Non-Uniform Residual Stress Evaluation by Using the Ring-Core Method
2016
Like other mechanical methods used for the residual stress evaluation on a generic structural component, the Ring-Core Method (RCM) is potentially subjected to various error sources that in some particular experimental conditions can lead to significant errors and/or uncertainties on the computed residual stresses. The accuracy of the residual stresses computed by the RCM can be improved by a proper error analysis that allows the user to correct the systematic errors, as well as to evaluate the remaining stress uncertainty due to the random errors. Therefore, in order to give a contribution to the accuracy of the RCM, in the present work the list of the main error sources is presented and t…
Experimental analysis of the contact pressure distribution in an off-road tyre
2009
In this paper the results of experimental tests are shown, lead by extended method of measurement, on a tire for an off-road vehicle 175/82 R16, inserting Prescale paper at the contact with the ground. The experimental analysis of the pressures is lead, in cross-sectional direction, in 5 zones correspondents to the middle of the single dowels constituting the tread. The results are analyzed by means of software predisposed to the scope so as to go back easily to the value of the pressure. The obtained results are critically analyzed and the result are compared with those obtained by the formulas of Rowland and MacLaurin, and by the nominal pressure at ground, concluding that the expression …
PAUT inspection of complex-shaped composite materials through six DOFs robotic manipulators
2015
The requirement to increase inspection speeds for the non-destructive testing (NDT) of composite aerospace parts is common to many manufacturers. The prevalence of complex curved surfaces in the industry provides significant motivation for the use of six-axis robots for the deployment of NDT probes in these inspections. The IntACom project, developed by TWI Technology Centre (Wales) and supported by a number of major aerospace partners and the Welsh government, has produced a prototype robotic NDT system. The prototype system is capable of inspecting complex-geometry composite components with great time savings. Two six-axis robotic arms deploy end effectors carrying phased array ultrasonic…
Finite Element Method Analysis of a Spur Gear with a Corrected Profile
2007
The difference between the stress value calculated by a two-dimensional finite element model of spur gears and those obtained by the rules in ISO 6336 was evaluated. Hertz theory, which provides information on the extension of the contact area and the maximum value of the contact pressure, was used to choose the dimensions of the elements. The mesh was created using the stress analytical solution relative to a model consisting of two cylinders in contact. Analogous optimization was executed for the mesh of the teeth feet; a mesh of 15 elements was considered optimum, because it minimized the difference to 0.5 per cent in the bending stress calculation. Stress values, obtained using the fin…
Defect Detection in Additively Manufactured Components: Laser Ultrasound and Laser Thermography Comparison
2018
Despite continuous technological advances in additive manufacturing, the lack of non-destructive inspection techniques during the manufacturing process is a limit for the industrial breakthroughs. Additive manufacturing is mainly used in industrial sectors where the zero defect target is crucial. The inclusion of the integrity assessment into the additive manufacturing process would allow corrective actions to be performed before the component is completed. To this end, the development of in-process monitoring and processing techniques is of great interest.This work proposes and compares two remote non-destructive inspection techniques: laser ultrasound and laser thermography. The two techn…
Evaluation of crack-closure by second harmonic thermoelastic stress analysis
2022
The work illustrates a new experimental approach to evaluate crack-closure in samples undergoing Fatigue Crack-Growing. Crack-closure leaves a peculiar signature on both amplitude and phase of the harmonic of the temperature signal at twice the loading frequency (Second Harmonic), due to the periodic nature of the internal elastic compression stresses. Thermoelastic Stress Analysis (TSA) is successfully applied to reveal such signatures on Single-Edge-Notched steel samples. A methodology is also proposed to evaluate the Crack-Opening-Load from temperature data. The work finally explores the influence of crack-closure on crack-tip identification and on the evaluation of the Stress Intensity …
Inspection of additive-manufactured layered components
2015
Laser powder deposition (LPD) is a rapid additive manufacturing process to produce, layer upon layer, 3D geometries or to repair high-value components. Currently there is no nondestructive technique that can guarantee absence of flaws in LPD products during manufacturing. In this paper a laser ultrasonic technique for in-line inspection of LPD components is proposed. Reference samples were manufactured from Inconel and machined flaws were created to establish the sensitivity of the technique. Numerical models of laser-generated ultrasonic waves have been created to gain a deeper understanding of physics, to optimize the set-up and to verify the experimental measurements. Results obtained on…