Search results for " crack"
showing 10 items of 92 documents
Discussion on “Experimental Deformation of Opalinus Clay at Elevated Temperature and Pressure Conditions: Mechanical Properties and the Influence of …
2021
AbstractThe testing procedure and results on saturated samples of Opalinus Clay in the work of Schuster et al. (Rock Mech Rock Eng https://doi.org/10.1007/s00603-021-02474-3, 2021) were conducted and presented using strain rates two to four orders of magnitudes higher than the rates needed to allow pore pressure equilibrium in the material, both in drained and undrained conditions. This leads to an erroneous estimation of the mechanical properties in saturated conditions. We discuss this aspect in the context of shale testing. We also discuss the effect of drying-induced fissuring on the mechanical properties of geomaterials tested in dry conditions.
Fatigue crack growth through particulate clusters in polycarbonate material
2011
The interaction of a crack with a perfectly bonded inclusion or a cluster of inclusions in polycarbonate matrix was investigated through both numerical simulations and fatigue tests. Stress intensity factors (K(I)) were evaluated by boundary element method for several particle sizes, position and finally for inclusion cluster as a precursor study for the experiments. The numerical simulation has shown the crack tendency to circumvent the inclusions with consequential reduction of the growth rate. Fatigue crack growth tests were carried out on several particle-filled specimens at constant value of the applied stress intensity factor range (Delta K(Iapp)) highlighting the crack delay due to t…
Analisi numerico-sperimentale per la determinazione delle tensioni residue in un giunto saldato
2013
La durata di un componente dipende dall’interazione tra le caratteristiche meccaniche del materiale con cui è costruito e gli sforzi a cui esso è sottoposto. Per la determinazione dello stato tensionale agente, oltre agli sforzi dovuti ai carichi imposti durante l’esercizio, è necessario conoscere accuratamente gli stati tensionali residui derivanti dal processo di produzione. Generalmente, le tensioni residue sono indesiderate poiché possono essere di entità elevata e tale da ridurre la resistenza complessiva del componente meccanico. Un aspetto particolarmente insidioso delle tensioni residue è che la loro presenza viene generalmente riconosciuta solo dopo il verificarsi di un malfunziona…
Residual Stresses Induced by Cold Expansion of Adjacent and Cut-Out Holes
2012
Fatigue life of fastener holes can be enhanced via a cold-expansion process to introduce a compressive residual stress field around the hole edge and to reduce crack growth propagation. Considering that aerospace components contain multiple rows of holes, the present investigation focuses on the evaluation of the three-dimensional residual stress distribution in adjacent cold-expanded (CE) holes. The redistribution of residual stresses caused by a cut introduced between two adjacent holes was also investigated. Finite element (FE) analysis and experimental technique were used to assess the residual stress distribution in a 6082-T6 aluminum plate with two adjacent holes expanded sequentially…
Simultaneous measurement of temperature and strain in glass fiber/epoxy composites by embedded fiber optic sensors: II. Post-cure testing
2007
In this paper the use of fiber optic sensors embedded into GFRP laminates for structural health monitoring of thermo-mechanical loads is presented. The proposed sensing system, consisting of two coupled fiber Bragg grating (FBG) sensors, allows the simultaneous measurement of both temperature and strain by decoupling the change in reflected wavelength induced by temperature variations from that induced by either mechanical or apparent strain, with significant advantages either for monitoring the composite cure kinetics, as described in the accompanying paper (Part I), or for assessing the structural response to thermo-mechanical loads. Both thermal ramp and mechanical static/dynamic bending…
Experimental application of digital image correlation for the tensile characterization of basalt FRCM composites
2021
Abstract Composites made with inorganic matrix, namely fabric reinforced cementitious mortar (FRCM) composites are becoming widespread as strengthening materials for existing masonry structures. These composites are made of a dry grid of fibres embedded in an inorganic matrix. FRCMs can be considered a valid alternative to traditional organic composites such as fibre reinforced polymers (FRPs) because of their better compatibility with the masonry support. This work presents an experimental study for the tensile characterization of a basalt fabric reinforced cementitious mortar (BFRCM) composite. Tensile tests were carried out on coupons reinforced with one, two or three layers of grid to i…
An unsupervised Learning Algorithm for Fatigue Crack Detection in Waveguides
2009
Ultrasonic guided waves (UGWs) are a useful tool in structural health monitoring (SHM) applications that can benefit from built-in transduction, moderately large inspection ranges, and high sensitivity to small flaws. This paper describes an SHM method based on UGWs and outlier analysis devoted to the detection and quantification of fatigue cracks in structural waveguides. The method combines the advantages of UGWs with the outcomes of the discrete wavelet transform (DWT) to extract defect-sensitive features aimed at performing a multivariate diagnosis of damage. In particular, the DWT is exploited to generate a set of relevant wavelet coefficients to construct a uni-dimensional or multi-di…
Outlier analysis and principal component analysis to detect fatigue cracks in waveguides
2009
Ultrasonic Guided Waves (UGWs) are a useful tool in structural health monitoring (SHM) applications that can benefit from built-in transduction, moderately large inspection ranges and high sensitivity to small flaws. This paper describes a SHM method based on UGWs, discrete wavelet transform (DWT), outlier analysis and principal component analysis (PCA) able to detect and quantify the onset and propagation of fatigue cracks in structural waveguides. The method combines the advantages of guided wave signals processed through the DWT with the outcomes of selecting defectsensitive features to perform a multivariate diagnosis of damage. The framework presented in this paper is applied to the de…
Application of principal component analysis and wavelet transform to fatigue crack detection in waveguides
2010
Ultrasonic Guided Waves (UGWs) are a useful tool in structural health monitoring (SHM) applications that can benefit from built-in transduction, moderately large inspection ranges and high sensitivity to small flaws. This paper describes a SHM method based on UGWs, discrete wavelet transform (DWT), and principal component analysis (PCA) able to detect and quantify the onset and propagation of fatigue cracks in structural waveguides. The method combines the advantages of guided wave signals processed through the DWT with the outcomes of selecting defect-sensitive features to perform a multivariate diagnosis of damage. This diagnosis is based on the PCA. The framework presented in this paper …
Automatic Segmentation and Enhancement of Pavement Cracks Based on 3D Pavement Images
2019
Pavement cracking is a significant symptom of pavement deterioration and deficiency. Conventional manual inspections of road condition are gradually replaced by novel automated inspection systems. As a result, a great amount of pavement surface information is digitized by these systems with a high resolution. With pavement surface data, pavement cracks can be detected using crack detection algorithms. In this paper, a fully automated algorithm for segmenting and enhancing pavement crack is proposed, which consists of four major procedures. First, a preprocessing procedure is employed to remove spurious noise and rectify the original 3D pavement data. Second, crack saliency maps are segmente…