Search results for " electronic engineering"
showing 10 items of 8284 documents
Contrasting topologies for regular interconnection networks under the constraints of nanoscale silicon technology
2010
Nowadays, system designers have adopted Networks-on-Chip as communication infrastructure of general-purpose tile-based Multi-Processor System-on-Chip (MPSoC). Such decision implies that a certain topology has to be selected to efficiently interconnect many cores on the chip. To ease such a choice, the networking literature offers a plethora of works about topology analysis and characterization for the off-chip domain. However, theoretical parameters and many intuitive assumptions of such off-chip networks do not necessarily hold when a topology is laid out on a 2D silicon surface. This is due to the distinctive features of silicon technology design pitfalls. This work is a first milestone t…
The Effect of the Harmonic Content Generated by AC/DC Modular Multilevel Converters on HVDC Cable Systems
2019
With the increasing penetration of renewable and decentralized energy sources into the power grid, an extended use of DC voltages is expected on both distribution and transmission levels. Generation of DC voltages by means of voltage source converters is associated with a wide spectrum of harmonic distortions at converter terminals, both on the ac and on the dc sides. This can lead to partial discharges in power cables, which deteriorate insulation material thus weakening its performance and reducing cable life-time. In the previously published paper, the effect of harmonic distortion on appearance of partial discharges in cable insulation was evaluated. Here, the study related to the PD be…
FOC with Resolver Implementation for PMSM Drives by Using a Low Cost Atmel SAM3X8E Microcontroller
2020
The aim of this paper is the low-cost experimental implementation of a field oriented control strategy for a Permanent Magnet Synchronous Motor (PMSM) by using an Atmel SAM3X8E microcontroller, mounted on an Arduino DUE board. In this electrical drive for PMSM, a resolver is used in order to measure the rotor position and speed: Therefore, the low-cost Arduino DUE performs not only FOC algorithm and phase currents data acquisition, but also a resolver-To-digital converter process, rotor position and speed data acquisition, and resolver signals management. The code has been implemented in the open source Arduino IDE, using C language, whereas the control and plot visualization interfaces hav…
A new technique for partial discharges measurement under DC periodic stress
2017
The aim of the present work is to recognize the type of defect in insulating materials employed in DC electrical systems. This analysis, under AC stress, is carried out by using the Phase Resolved method (PRPD). While, under constant voltage stress this method cannot be performed and measurements show complexities. In order to overcome these problems, a new technique is proposed, based on the application of a periodic continuous waveform. Simulation results, carried out by using a model based on a time-variable conductance of an air void defect, showed the PRPD pattern that can be obtain. Furthermore, compared to the constant DC stress, the measurement duration became lower and the discharg…
Acoustic Wave Behavior in a Specimen Containing an Air Void Defect
2019
The PEA method is the most used technique for the space charge measurements. As is well known, this method uses pressure waves to detect the charges accumulated in solid dielectrics. Based on its working principle, the generated acoustic waves travel within PEA cell and the specimen under test in order to be finally detected by the piezoelectric sensor. For a multilayer specimen and, in particular, in case of different materials that make up the specimen, the acoustic wave reflection is inevitable. Considering that, in several cases, the reflected waves could be detected by the piezoelectric sensor before than the main signals, the PEA cell output profile could results distorted. Based on t…
Tetrahedral versus octahedral Mn site coordination in wurtzite and rocksalt Zn1−xMnxO investigated by means of XAS experiments under high pressure
2007
Abstract We present the results of x-ray absorption measurements carried out in Zn 1− x Mn x O thin films under high pressure. The Mn environment remains essentially the same for nominal Mn concentrations given by x = 0.05 , 0.1, 0.15 and 0.25. Both the XANES (X-ray Absorption Near Edge Structure) and EXAFS (Extended X-ray Absorption Fine Structure) indicate that Mn occupies the Zn site, being surrounded by four oxygen atoms at 2.02±0.01 A. The substitutional hypothesis is reinforced by comparing the differences between the ambient (wurtzite) and high pressure (rocksalt) spectra, which correspond to tetrahedral and octahedral Mn environments.
Real-time signal processing in embedded systems
2016
International audience
Run-time scalable NoC for FPGA based virtualized IPs
2017
The integration of virtualized FPGA-based hardware accelerators in a cloud computing is progressing from time to time. As the FPGA has limited resources, the dynamic partial reconfiguration capability of the FPGA is considered to share resources among different virtualized IPs during runtime. On the other hand, the NoC is a promising solution for communication among virtualized FPGA-based IPs. However, not all the virtualized regions of the FPGA will be active all the time. When there is no demand for virtualized IPs, the virtualized regions are loaded with blank bitstreams to save power. However, keeping active the idle components of the NoC connecting with the idle virtualized regions is …
Computer-aided analysis and design procedure for rotating induction machine magnetic circuits and windings
2018
The aim of this study is to present a new, accurate, and user-friendly software procedure for the analysis and rapid design of rotating induction machine windings, considering both the electric and the magnetic specifications of the machine itself. This procedure is a valid aid for quick first stage design without the necessity of using finite element method (FEM)-based design procedures. FEM can be used in a second design phase in order to refine the first stage results. The design procedure is hereafter outlined and some examples show its capability.
Review of the PEA Method for Space Charge Measurements on HVDC Cables and Mini-Cables
2019
This review takes into account articles and standards published in recent years concerning the application of the Pulsed Electro Acoustic (PEA) method for space charge measurement on High Voltage Direct Current (HVDC) cables and mini-cables. Since the 80s, the PEA method has been implemented for space charge measurements on flat specimens in order to investigate space charge phenomena and to evaluate the ageing of dielectrics. In recent years, this technique has been adapted to cylindrical geometry. Several studies and experiments have been carried out on the use of the PEA method for full size cables and HVDC cable models. The experiments have been conducted using different arrangements of…