Search results for " engineering"
showing 10 items of 38291 documents
Spectroscopic study of the electric field induced valence change of Fe-defect centers in SrTiO(3)
2011
The electrochemical changes induced by an electric field in Fe-doped SrTiO(3) have been investigated by X-ray absorption spectroscopy (XANES and EXAFS), electron paramagnetic resonance (EPR) and Raman spectroscopy. A detailed study of the Fe dopant in the regions around the anode and cathode reveals new insights into the local structure and valence state of Fe in SrTiO(3) single crystals. The ab initio full multiple-scattering XANES calculations give an evidence of the oxygen vacancy presence in the first coordination shell of iron. Differences in the length and disorder of the Fe-O bonds as extracted from EXAFS are correlated to the unequivocal identification of the defect type by compleme…
FOC with Resolver Implementation for PMSM Drives by Using a Low Cost Atmel SAM3X8E Microcontroller
2020
The aim of this paper is the low-cost experimental implementation of a field oriented control strategy for a Permanent Magnet Synchronous Motor (PMSM) by using an Atmel SAM3X8E microcontroller, mounted on an Arduino DUE board. In this electrical drive for PMSM, a resolver is used in order to measure the rotor position and speed: Therefore, the low-cost Arduino DUE performs not only FOC algorithm and phase currents data acquisition, but also a resolver-To-digital converter process, rotor position and speed data acquisition, and resolver signals management. The code has been implemented in the open source Arduino IDE, using C language, whereas the control and plot visualization interfaces hav…
A new technique for partial discharges measurement under DC periodic stress
2017
The aim of the present work is to recognize the type of defect in insulating materials employed in DC electrical systems. This analysis, under AC stress, is carried out by using the Phase Resolved method (PRPD). While, under constant voltage stress this method cannot be performed and measurements show complexities. In order to overcome these problems, a new technique is proposed, based on the application of a periodic continuous waveform. Simulation results, carried out by using a model based on a time-variable conductance of an air void defect, showed the PRPD pattern that can be obtain. Furthermore, compared to the constant DC stress, the measurement duration became lower and the discharg…
Acoustic Wave Behavior in a Specimen Containing an Air Void Defect
2019
The PEA method is the most used technique for the space charge measurements. As is well known, this method uses pressure waves to detect the charges accumulated in solid dielectrics. Based on its working principle, the generated acoustic waves travel within PEA cell and the specimen under test in order to be finally detected by the piezoelectric sensor. For a multilayer specimen and, in particular, in case of different materials that make up the specimen, the acoustic wave reflection is inevitable. Considering that, in several cases, the reflected waves could be detected by the piezoelectric sensor before than the main signals, the PEA cell output profile could results distorted. Based on t…
Positron trapping defects in free-volume investigation of Ge–Ga–S–CsCl glasses
2016
Abstract Evolution of free-volume positron trapping defects caused by crystallization process in (80GeS 2 –20Ga 2 S 3 ) 100−х (СsCl) x , 0 ≤ x ≤ 15 chalcogenide-chalcohalide glasses was studied by positron annihilation lifetime technique. It is established that CsCl additives in Ge–Ga–S glassy matrix transform defect-related component spectra, indicating that the agglomeration of free-volume voids occurs in initial and crystallized (80GeS 2 –20Ga 2 S 3 ) 100−х (СsCl) x , 0 ≤ x ≤ 10 glasses. Void fragmentation in (80GeS 2 –20Ga 2 S 3 ) 85 (СsCl) 15 glass can be associated with loosing of their inner structure. Full crystallization in each of these glasses corresponds to the formation of defe…
Synergistic effect of fiber content and length on mechanical and water absorption behaviors of Phoenix sp. fiber-reinforced epoxy composites
2016
Phoenix sp. fiber-reinforced epoxy composites have been manufactured using compression molding technique. The effect of reinforcement volume content (0%, 10%, 20%, 30%, 40%, and 50%) and size (300 µm particles, 10 mm, 20 mm, and 30 mm fibers) on quasi-static and dynamic mechanical properties was investigated. Moreover, the water absorption properties of composites were analyzed at different environmental conditions (10℃, 30℃, and 60℃). For each reinforcement size, composites loaded with 40% in volume show highest tensile and flexural properties. Furthermore, composites with 300 µm particles present the best impact properties and the lowest water absorption, regardless of the environmental …
High sensitivity characterization of the nonlinear electric susceptibility of a glass ceramic in the microwave range
2019
The nonlinear electric susceptibility of a glass ceramic is characterized in the microwave range by measuring intermodulation of two high-power signals. To achieve the necessary sensitivity for dielectric nonlinearities, the setup ensures that the measured intermodulation can be ascribed to the material under test while all other intermodulation sources are suppressed. This is achieved by coupling three dielectric resonators in a cut-off waveguide. The third order nonlinearity of the glass ceramic is found to be χ3/er = (1.6 ± 0.8) × 10−15 m2/V2 at 950 MHz. The magnitude is comparable to the previously measured high-end sintered ceramics. The power of the intermodulation signal as a functio…
Parametric Models for Predicting the Performance of Wind Turbines
2020
Abstract Performances of eight parametric power curve models for wind turbines, which can be used for the planning and management of wind energy projects, are compared in this study. Initially, the manufacturer’s power curves of four wind turbines are compared with their field performances. Then, the parametric models are developed for these turbines which are tested with their site performances. Out of the models, WERA showed the best performance in case of all the turbines. Finally, a method for using WERA in extrapolating the performance of turbines with limited test data is demonstrated with the case of a 1 kW turbine.
Long term stability testing of oxide unicouple thermoelectric modules
2019
Thermoelectric devices based on oxides are good candidates for energy harvesting technologies for use in aggressive conditions where the materials should withstand high temperatures and corrosive environments over prolonged time. This leads to a natural concern for the stability of the electrical contacts, especially on the hot side of the module. In this work, we have assembled several prototype unicouple thermoelectric modules made by pyrolyzed and spark plasma sintered n-type CaMnO3 and p-type Ca3Co4O9 and then tested under different conditions mimicking end-user applications. For baseline experiments we have chosen to use nickel as the contact material in order to show the effect of its…
Simulation of IQE tuning of individual cells for DC-balancing multijunction tandem cells
2016
In the present work, the performance of stacks of cells connected in series is examined at different levels of internal quantum efficiency (IQE). Incident photons, generated by employing the ASTM G173-03 data set, are accounted for individually as they interact with the stack of cells. The efficiencies of the devices studied are dependent upon the DC balance throughout the stack of cells. It is demonstrated that reducing the internal quantum efficiency of upper cells can lead to a better DC balance and thereby higher efficiency.