Search results for " epoxy"

A comparative study of fatigue behaviour of flax/epoxy and glass/epoxy composites

2012

Experimental investigations on flax and glass fabrics reinforced epoxy specimens, i.e. FFRE and GFRE, submitted to fatigue tests are presented in this paper. Samples having [0/90]3S and [±45]3S stacking sequences, with similar fibre volume fractions have been tested under tension–tension fatigue loading. The specific stress-number of cycles to failure (S–N) curves, show that for the [0/90]3S specimens, FFRE have lower fatigue endurance than GFRE, but the [±45]3S FFRE specimens offer better specific fatigue endurance than similar GFRE, in the studied life range (<2 × 10^6). Overall, the three-stage stiffness degradation is observed in all cases except for [0/90]3S FFRE specimens, which prese…

Toward high performance renewable agave reinforced biocomposites: Optimization of fiber performance and fiber-matrix adhesion analysis

2017

Abstract The increasing sensitivity toward the environmental pollution and the recent laws on the environmental protection, have led to an increasing attention to the so called biocomposites, i.e. to ecofriendly or renewable composite materials, obtained from biopolymers reinforced by natural fibers. Although the contribution of various works reported in literature, focused on biocomposites reinforced by agave fibers, such materials are still exclusively used in the automotive industry for non-structural applications, and the implementation of high performance biocomposites for semi-structural and structural applications, is an expected, but not yet reached objective. Therefore, the present…

Static and dynamic mechanical properties of Arundo Donax fillers-epoxy composites

2014

Abstract Aim of this work is to investigate the feasibility of using a natural and inexpensive filler obtained by grinding the culms of Arundo Donax as reinforcement of epoxy resins. The effect of the content and size of Arundo Donax fillers on static and dynamic mechanical properties was evaluated showing that the composites exhibit higher tensile moduli, comparable flexural moduli and lower strength properties in comparison to the neat resin. Moreover, changes in the storage and the loss moduli only above the glass transition temperature (i.e. in the rubbery region) were found while neither significant shifts of tan δ peaks to higher temperatures nor reductions in the peak height of the c…

Experimental Investigation and Finite Element Analysis of Dynamic Behavior and Damage of Glass/Epoxy Tubular Structures

2011

This paper presents finite element analysis (FEA) of static and dynamic tests of thick filament wound glass/epoxy tubes. The first part involves the validation of elastic properties and identification of damage initiation and its development in dynamic tests. The results of FEA of the dynamic tests without damage appeared satisfactory. An impact model, including material property degradation, is used for damage prediction. The simulated damage is compared with that obtained experimentally. The sizes of projected and cumulated surfaces are of the same order of magnitude as in the experimental measurements.

The Influence of Ageing on the Impact Damage of Carbon Epoxy Composites

2011

Abstract This study looks into the influence of ageing on the carbon epoxy composite when impact is applied. Three different stacking sequences were investigated, one sequence with the classic lay-up, whereas the other two have quasi-isotropic and quasi-homogeneous behaviour. The specimens were aged up to 2100 h (3 months) in a climatic chamber with a temperature of 70 °C and relative humidity of 85%. The mass was measured regularly during the hygrothermal ageing treatment. The mass was always measured directly after exiting the climatic chamber and it was noted that for each stacking sequence, the same regular increase in mass is observed until stabilisation. The specimens were then impact…

The influence of the rubber carboxyl functionality on the processability and properties of solid rubber modified epoxy mixtures

2005

A high molecular weight, carboxyl functionalised solid rubber was added to an epoxy resin-aromatic amino system developed for autoclave curing of honeycomb core composite structures. The achievement of an optimal balance of viscous flow and viscoelasticity of the resin, by controlling the nature and extent of cross-linking of the functionalised rubber, was proposed as a route to void-free honeycomb skins. The aim of the present investigation is to understand how the concentration of carboxylic groups of the rubber, prereacted with one of the epoxy monomers, affects the matrix resin flow properties. The concentration of carboxyl groups was changed by reacting them with a monofunctional epoxy…

Evaluation of the temperature effect on the fractional linear viscoelastic model for an epoxy resin

2016

The paper deals with the evolution of the parameters of a fractional model for different values of temperature. An experimental campaign has been performed on epoxy resin at different levels of temperature. It is shown that epoxy resin is very sensitive to the temperature.

Prédiction de la contrainte de rupture de composites unidirectionnels et suivi de l'accumulation de ruptures de fibres

2005

Epoxy resin based matrices for advanced composites cured by ionizing radiation. Study of the influence of process parameters on final properties

2006

Radiation curing of carbon fibre composites

2014

Epoxy/carbon fibre reinforced composites were produced by means of e-beam irradiation through a pulsed 10 MeV electron beam accelerator. The matrix consisted of a difunctional epoxy monomer (DGEBA) and an initiator of cationic polymerisation, while the reinforcement was a unidirectional high modulus carbon fibre fabric. Dynamic mechanical thermal analysis was carried out in order to determine the cross-linking degree. The analysis pointed out a nonuniformity in the cross-linking degree of the e-beam cured panels, with the formation of clusters at low Tg (glass transition temperature) and clusters at high Tg. An out-of-mould post irradiation thermal treatment on e-beam cured samples provides…