Search results for " inductor."
showing 7 items of 17 documents
Non-Linear Inductors Characterization in Real Operating Conditions for Power Density Optimization in SMPS
2021
The exploitation of power inductors outside their linear region in switching converters can be achieved by raising the current until a decreasing of the inductance can be noticed. It allows using a smaller magnetic core increasing the power density of the converter. On the other hand, a detailed description of the magnetization curve including the temperature is required. Since this information is often not included in the inductor’s datasheets, this paper shows how to identify the behavior of an inductor when it is operated up to saturation and its temperature rises. In order to characterize the inductor in real operating conditions, a dedicated measurement rig has been developed. It consi…
Design and Modeling of an Interleaving Boost Converter with Quasi-Saturated Inductors for Electric Vehicles
2020
This paper is focused on the analysis and modeling of DC-DC boost converters in interleaving configuration exploiting inductors in the quasi-saturation region. The converter is designed to optimize the power density by minimizing the size of the inductors. A simulation study for electric vehicle applications is conducted analyzing the effects of duty cycle and temperature variation on the ripple of the input current giving, moreover, information on the performances and dynamics of the converter for further implementation and optimizations.
Impact of Nonlinear Inductor on Efficiency and Power Losses in a SMPS: a Case Study
2022
This paper proposes a comparative analysis focused on losses in two Switched Mode Power Supplies, adopting a linear inductor and an inductor operated up to saturation, respectively. The use of the nonlinear inductor saves weight and cost on the magnetic material, which is of great interest for automotive applications; however, it increases the peak current and can increase losses. The analysis aims to compare, by simulations, the impact on the efficiency of the different current waveforms throughout the converter. The losses are discussed in detail and calculated for each component of the converters.
PCB-Based Planar Inductive Loops for Partial Discharges Detection in Power Cables
2022
Partial discharge (PD) diagnosis tests, including detecting, locating, and identifying, are used to trace defects or faults and assess the degree of aging in order to monitor the insulation condition of medium- and high-voltage power cables. In this context, an experimental evaluation of three different printed circuit board (PCB)-based inductive sensor topologies, with spiral, non-spiral, and meander shapes, is performed. The aim is to assess their capabilities for PD detection along a transmission power cable. First, simulation and experimental characterization are carried out to determine the equivalent electrical circuit and the quality factor of the three sensors. PD activity was studi…
Output Impedance Improvement Using Coupled Inductors
2017
When using a single DC/DC converter with multiple outputs and having a buck topology, which has one filter inductor per output, the designer can choose to couple these outputs together. This paper demonstrates additional benefits of coupling output inductors together. Apart from saving mass and volume, and due to an improved small signal behaviour it also reduces the output impedance of the regulated output. The paper will analyse a seven output push-pull converter used as a space power converter module and verify the theoretical results with experimental measurements.
Design and realization of a DC/DC converter with a partially saturated inductor
2017
DC/DC converters, in some types of applications such as portable equipments, can require more space than it is actually available. The inductor is typically the most bulky element and the possibility to reduce its size can save up to 50% of the converter volume and area [1][2], thus increasing the power density. This reduction, however, comes with nonlinear effects caused by the saturation of the ferromagnetic core. An appropriate modelling of the inductor and of the converter circuit is needed for guaranteeing a good output power quality (Fig. 1). A Boost converter with an inductor in the partially saturated roll-off operating zone was designed and realized to study the behaviour of DC/DC …
Non-Linear Inductor Models Comparison for Switched-Mode Power Supplies Applications
2022
The use of non-linear power inductors, intended as devices exploited up to a current at which the inductance is halved, is of great interest in switched-mode power supplies (SMPSs). Indeed, it allows the use of lighter and cheaper inductors improving the power density. On the other hand, the analysis of SMPSs equipped with non-linear inductors requires appropriate modeling of the inductor reproducing the inductance versus current. This paper compares two main analytical models proposed in the literature: the former is based on a polynomial, and the latter exploits the arctangent function to reproduce the non-linearity of the inductance. Performance is compared by considering the effort of r…