Search results for " interface"
showing 10 items of 1741 documents
The influence of thin hard coatings on frictional behaviour in the orthogonal cutting process
2000
New knowledge about the tribological response deriving from the interaction of the substrate/coating-chip system, with special attention to the orthogonal cutting process when chatter-free end turning using natural contact tools, is developed. In order to evaluate the frictional behaviour of this process under modified contact conditions, experimental investigations including the contact temperature, the contact loads, friction and the frictional heat flux per unit area were carried out. In contrast to the most obvious approach, the coefficient of sliding friction versus the cutting speed, the contact temperature, the normal pressure and the interface control factor is considered. A number …
Microstructural evolution of wear-resistant FeCrB and FeCrNiCoB coating alloys during high-energy mechanical attrition
2008
Mechanical milling/attrition provides a convenient scope of simulating the microstructural changes encountered by wear-resistant coating alloys subjected to deformation under high frequency and high-intensity impact loading or accelerated wear condition. In the present study, the microstructural evolution of two commercial coating materials, FeCrB (Armacor M) and FeCrNiCoB (Armacor C), in the course of low- and high-intensity mechanical attrition, was monitored by X-ray diffraction and high-resolution transmission electron microscopy. While low-intensity milling leads to marginal grain refinement but no change in phase-aggregate in FeCrB, similar mechanical attrition causes boride precipita…
Influence of friction on the local mechanical and electrochemical behaviour of duplex stainless steels.
2006
International audience; The electrochemical behaviour of ferritic and austenitic phases in duplex stainless steel (UNS S32304) and the modifications induced by straining during sliding were studied by potentiodynamic polarisation curves determined at the microscale in a 1MNaCl (pH 3) solution, using an electrochemical microcell. The mechanical properties and stress state of each phase were determined by microhardness and X-ray microdiffraction measurements, before and after straining. The results show that sliding generates elastic straining of the ferrite and plastic deformation of the austenite. The electrochemical behaviour of these phases is dramatically altered, inducing a reduction of…
Oscillatory Changes of the Heterogeneous Reactive Layer Detected with the Motional Resistance during the Galvanostatic Deposition of Copper in Sulfur…
2015
Metallic copper was galvanostatically deposited on quartz|gold resonant electrodes by applying a constant current in a 0.5 M CuSO4/0.1 M H2SO4 aqueous solution. Galvanostatic copper deposition is one of the best methodologies to calibrate the electrochemical quartz crystal microbalances (EQCM), a gravimetric sensor to evaluate changes in mass during the electrochemical reactions through the Sauerbrey equation. The simultaneous measurement of mass, current density, and motional resistance by an EQCM with motional resistance monitoring allows us to characterize the processes occurring on the electrode surface and at the interfacial regions with unprecedented detail. During the galvanostatic c…
Manipulating Self-Avatar Body Dimensions in Virtual Worlds to Complement an Internet-Delivered Intervention to Increase Physical Activity in Overweig…
2020
Virtual reality has been found to be a useful tool for positively influencing relevant psychological variables in order to increase physical activity (PA), especially in the overweight population. This study investigates the use of avatars and their physical variations to extend the effectiveness of existing interventions to promote PA. The main objective is to analyze the influence of the avatars&rsquo
Many-body perturbation theory calculations using the yambo code
2019
Abstract yambo is an open source project aimed at studying excited state properties of condensed matter systems from first principles using many-body methods. As input, yambo requires ground state electronic structure data as computed by density functional theory codes such as Quantum ESPRESSO and Abinit. yambo’s capabilities include the calculation of linear response quantities (both independent-particle and including electron–hole interactions), quasi-particle corrections based on the GW formalism, optical absorption, and other spectroscopic quantities. Here we describe recent developments ranging from the inclusion of important but oft-neglected physical effects such as electron–phonon i…
Assessing B.A.Bar Device as a Tool for Supporting Labour Integration of a Severely Affected Person with Autism Who Carries Out Classifying Tasks
2004
This paper describes the case research carried out to demonstrate the utility of a specific technical aid (adapted bar code reader) to train an adult with severe autism in the performance of a work task of classifying products in a shop. The individual with autism who participated in this research has a combination of difficulties (degree of 76 percent of disability and unable to learn to read and write) and abilities (being able to follow single verbal instructions). Positive results are expounded together with considerations about the desirable features of future products that would overcome the mere training process and also be useful for the final and real task in any working environmen…
Numerical modelling of the tensile behaviour of BFRCM strips
2019
This paper aims at investigating the tensile behaviour of basalt fibres on cementitious matrix for the strengthening of masonry structures. The use of Basalt Fibre Reinforced Cementitious Matrix (BFRCM) is favourably considered by the scientific community because it represents a natural composite material with high compatibility with stone and masonry substrate. The study is developed through the generation of Finite Element (FE) models capable of reproducing the tensile behaviour of BFRCM strips with different number of layers of grid. For the scope, the micro-modelling approach is adopted assuming different levels of detail for the simulation of the interface constitutive behaviour. Fibre…
Mobility and fluxes of major, minor and trace metals during basalt weathering and groundwater transport at Mt. Etna volcano (Sicily)
2000
Abstract The concentrations and fluxes of major, minor and trace metals were determined in 53 samples of groundwaters from around Mt Etna, in order to evaluate the conditions and extent of alkali basalt weathering by waters enriched in magma-derived CO 2 and the contribution of aqueous transport to the overall metal discharge of the volcano. We show that gaseous input of magmatic volatile metals into the Etnean aquifer is small or negligible, being limited by cooling of the rising fluids. Basalt leaching by weakly acidic, CO 2 -charged water is the overwhelming source of metals and appears to be more extensive in two sectors of the S-SW (Paterno) and E (Zafferana) volcano flanks, where out …
Geochemical mapping of magmatic gas–water–rock interactions in the aquifer of Mount Etna volcano
2001
Abstract Systematic analysis of major and minor elements in groundwaters from springs and wells on the slopes of Mt. Etna in 1995–1998 provides a detailed geochemical mapping of the aquifer of the volcano and of the interactions between magmatic gas, water bodies and their host rocks. Strong spatial correlations between the largest anomalies in pCO2 (pH and alkalinity) K, Rb, Mg, Ca and Sr suggest a dominating control by magmatic gas (CO2) and consequent basalt leaching by acidified waters of the shallow (meteoric) Etnean aquifer. Most groundwaters displaying this magmatic-type interaction discharge within active faulted zones on the S–SW and E lower flanks of the volcanic pile, but also in…