Search results for " material"
showing 10 items of 17428 documents
Properties of Nanosized Ferrite Powders and Sintered Materials Prepared by the Co-Precipitation Technology, Combined with the Spray-Drying Method
2016
Cobalt and nickel ferrites powders are synthesized by the co-precipitation technology, combined with the spray-drying method. The crystallite size, specific surface area (SSA), magnetic properties of synthesized products are investigated. All the synthesized ferrites are nanocrystalline single phase materials with crystallite size of 5-6 nm, the SSA of 80-85 m2/g and the calculated particle size of 13-15 nm. After spray-drying granules of the size up to 10 μm are obtained. After thermal treatment at 550 and 950 °C SSA decreases to 40-50 m2/g and 20-22 m2/g, respectively. The saturation magnetization at these temperatures increase from 17 to 40 emu/g for NiFe2O4 and from 51 to 77 emu/g for C…
Structural, microstructural and dielectric studies in multiferroic LaSrNiO4-δ prepared by mechanical milling method
2016
Abstract The solid solution LaSrNiO 4-δ has been successfully prepared by a rapid method combining mechanical milling and heat treatment. The structure and microstructure transformations were characterized by X-ray powder diffraction, scanning and transmission electron microscopy. The dielectric property was also investigated. After 10 h of milling and 8 h of heat treatment at 1300 °C, X-ray diffraction analysis revealed LaSrNiO 4-δ single phase, exhibiting tetragonal structure with space group of I4/mmm. This result was confirmed by using the ED pattern for sample using the [001] orientation. The corresponding lattice images show the compound to be well ordered, indicating the absence of s…
Improve the dielectric properties of PrSrNi0.8Mn0.2O4 compounds by longer mechanical milling
2018
Abstract Structural and dielectric properties of PrSrNi 0.8 Mn 0.2 O 4 ceramics elaborated by a rapid method combining mechanical milling and heat treatment were studied for the first time. The raw materials are milled at different times ( t mil = 0, 5, 10, 20 and 30 h) and annealed at 1300 °C for 8 h to produce a revealed PrSrNi 0.8 Mn 0.2 O 4 single phase, exhibiting tetragonal structure with space group I 4/ mmm . This result was confirmed by using the TEM/ED pattern for sample milled at 30 h using the [001] orientation. The corresponding lattice images show a well-ordered compound, indicating the absence of stacking faults and the growth of the crystallites. Giant dielectric response …
Recent progress in understanding the persistent luminescence in SrAl 2 O 4 :Eu,Dy
2019
Ever since the discovery of SrAl2O4:Eu,Dy persistent afterglow material, that can intensively glow up to 20 h, the mechanism of long-lasting luminescence has been a popular area of research. The re...
Characteristics of Sintered Materials Obtained from Ferrite Nanopowders Synthesised with Different Methods
2018
Ferrite materials, especially those containing nickel and cobalt, are popular due to their unique mechanical and magnetic properties. Single phase NiFe2O4 and CoFe2O4 nanopowders obtained by different methods were used for sintering studies. Chemical sol-gel self-propagating combustion method, co-precipitation technology combined with hydrothermal synthesis or spray-drying method, and high frequency plasma chemical synthesis have been used to synthesize ferrite nanopowders. Relatively dense (95-99%) materials with high saturation magnetization (MS = 80-84 emu/g for CoFe2O4 and MS = 46-48 emu/g for NiFe2O4) were obtained at 1100-1200 °C temperatures.
The Matrix Effect and Application of the Multi-Parameter Optimization Method for X-Ray Spectrometric Determination of the Quantitative Composition of…
2018
Determining the quantitative composition of clay samples with X-ray fluorescent spectrometry is complicated because of the matrix effect, in which any element can increase or decrease the analytical signals of other elements. In order to predict the properties of clays, it is essential to know their precise chemical composition. Therefore, using the standard addition method was determined calibration and empirical influence coefficients, as well as the true composition of the elements. Farther, these coefficients were used to correct the matrix effect and develop a multi-parameter optimization method. It was determined that in clay samples, consisting of Si, Al, Fe, K, Mg, Ca, Na and Ti oxi…
Microstructure and electric properties of low-pressure plasma sprayed β-FeSi 2 based coatings
2017
Abstract Thermoelectric material β-FeSi 2 based coating was fabricated by the technique low-pressure plasma spray (LPPS) on the Al 2 O 3 substrate from different alloy powders. During the process LPPS, the phase transformation had occurred through the peritectoid, eutectoid reaction and their inverse reaction. The grain size of the as-sprayed β-FeSi 2 doped Co coatings was reduced comparing with the original feedstock powders, which implied the thermal conductivity could effectively decreased by the LPPS process. The room temperature electrical conductivity showed metal and semiconductor properties on the as-sprayed and annealed coatings. This method and the results could solve the problems…
Synthesis of FeAl Hetero-Nanostructured Bulk Parts via Spark Plasma Sintering of Milled Powder
2006
AbstractSpark plasma sintering (SPS) has been used in order to introduce nanocrystalline grains within fully dense FeAl consolidated parts. Hetero-nanostructured parts, consisting of nano, ultrafine and micrometric grains, have been successfully processed when milled - Y2O3 reinforced - FeAl powder was used. The large temperature differences that are spontaneously generated during the SPS process as well as the use of milled powder account for the formation of such interesting structures. The grain size distribution - that is suggested to be very potent to improve both strength and ductility - could be significantly modified by a proper selection of sintering temperature and holding time.
Investigation of mechanical and electrical properties of Li doped sodium niobate ceramic system
2016
ABSTRACTThe Na0.96Li0.04NbO3 ceramic solid solution was prepared by means of a two-stage hot-pressing technology. The X-ray diffraction analysis showed the formation of a single perovskite phase with an orthorhombic symmetry in the investigated composition. The microstructure and EDS measurements were performed. They confirmed the high purity and the expected qualitative composition. A good homogeneity of the microstructures and a small degree of porosity were observed. The elastic modulus (the Young's modulus E, shear modulus G, and Poisson's ratio ν) of Na0.96Li0.04NbO3 were determined with the use of an ultrasonic method. The electrical properties of Na0.96Li0.04NbO3 ceramics were invest…
Long-term moisture absorption and durability of FRP pultruded rebars
2021
Abstract Up to 15-years long moisture diffusion into carbon, glass, and aramid fiber reinforced plastic (FRP) rebars is studied. To eliminate uncertainties in identification of the radial and axial diffusivities, a successive methodology for determination of the diffusion coefficients is proposed. The concept of apparent diffusivity taking into account anisotropy and edge effects is extended to cylindrical samples. The ratio of the axial and radial diffusivities is the lowest for carbon (3) and the highest for glass (81) FRP rebars. Durability performance of the rebars is estimated by monitoring their interlaminar shear strength (ILSS). Long-term exposure of FRP rebars in a humid environmen…