Search results for " mechanical propertie"
showing 10 items of 79 documents
A comparative study of fatigue behaviour of flax/epoxy and glass/epoxy composites
2012
Experimental investigations on flax and glass fabrics reinforced epoxy specimens, i.e. FFRE and GFRE, submitted to fatigue tests are presented in this paper. Samples having [0/90]3S and [±45]3S stacking sequences, with similar fibre volume fractions have been tested under tension–tension fatigue loading. The specific stress-number of cycles to failure (S–N) curves, show that for the [0/90]3S specimens, FFRE have lower fatigue endurance than GFRE, but the [±45]3S FFRE specimens offer better specific fatigue endurance than similar GFRE, in the studied life range (<2 × 10^6). Overall, the three-stage stiffness degradation is observed in all cases except for [0/90]3S FFRE specimens, which prese…
Beta forging of Ti-6Al-4V: Microstructure evolution and mechanical properties
2013
Titanium alloys are finding an increasing use in the aeronautical field, due to their characteristics of high mechanical properties, lightness and corrosion resistance. Moreover these alloys are compatible with the carbon fibre reinforced plastics that are also finding a wide use in the aeronautical field. On the other hand the use of these alloys implies some drawbacks, for example titanium alloys are often considered more difficult to form and generally have less predictable forming characteristics than other metallic alloys such as steel and aluminum. In this paper was studied both the microstructure evolution and the mechanical properties of a Ti-6Al-4V rolled bar after hot forging. The…
Multifunctional properties of nanocomposites made by 1D and 2D graphene based fillers
2015
High aspect ratio graphene based fillers with different dimensionalities showed the ability to greatly modify rheological, mechanical, thermal and electrical properties of polymers at very low content. In this work, the effect of filler dimensionality on the multifunctional properties of an epoxy matrix reinforced by both carbon nanotubes (1D) and graphite nanoplatelets (2D) have been investigated across the percolation region. Keywords-- Carbon nanotube, Graphite nanoplatelet, nanocomposites, mechanical properties, ...
CuO nanoparticle filled vinyl-ester resin nanocomposites: Fabrication, characterization and property analysis
2007
Abstract Both unmodified cupric oxide (CuO) nanoparticles and those functionalized with a bi-functional coupling agent methacryloxypropyl-trimethoxysilane (MPS) were used to fabricate vinyl-ester resin polymeric nanocomposites. The nanoparticle functionalization was observed to have a significant effect on the physical properties of the cupric oxide filled vinyl-ester resin nanocomposite. Thermal degradation study by thermo-gravimetric analysis (TGA) showed the increased thermo-stability in the functionalized-nanoparticle-filled vinyl-ester resin nanocomposites as compared with the unmodified-nanoparticle-filled counterparts. The more uniform particle dispersion and the chemical bond betwee…
Mechanical and rheological properties of polystyrene-block-polybutadiene-block-polystyrene copolymer reinforced with carbon nanotubes: effect of proc…
2017
Abstract Styrene-b-butadiene-b-styrene (SBS)-based nanocomposites filled with unmodified and –COOH functionalized carbon nanotubes (CNTs) have been formulated at different processing conditions in order to provide an understanding of the influence of the processing temperature and mixing speed on the nanofillers dispersion and on the overall properties of the nanocomposites. The evaluation of the nanocomposites’ mechanical and rheological behavior reveals that the effect of the processing speed on the final properties is almost negligible. Differently, the processing temperature influences strongly the mechanical and rheological properties of SBS-based nanocomposites. Indeed, for the nanoco…
Experimental assessment of the improved properties during aging of flax/glass hybrid composite laminates for marine applications
2018
The investigation for natural fibers composites in terms of performance, durability, and environmental impact for structural applications in marine environments is a relevant challenge in scientific and industrial field. On this context, the aim of this work is to assess the durability and mechanical stability in severe environment of epoxy/glass–flax hybrid composites. For the sake of comparison, also full flax and glass epoxy composites were investigated. All samples were exposed to salt–fog environmental conditions up to 60 aging days. Wettability behavior during time was compared with water uptake evolution to assess water sensitivity of hybrid composite configurations. Moreover, quasi-…
Physical properties of virgin-recycled ABS blends: Effect of post-consumer content and of reprocessing cycles
2012
Abstract Virgin/post-consumer ABS (pc-ABS) blends were re-processed and re-formed up to three times. The effect of pc-ABS content and of reprocessing cycles on the physical properties of the prepared blends was evaluated by mechanical tests (tensile, flexural and impact tests) and by rheological and thermo-mechanical measurements. The processability of pc-ABS blends was not substantially different by that of virgin ABS up to two recycling steps even if the third one induced a slightly decrease of viscosity, more remarkable on increasing the pc-ABS content. The mechanical and thermo-mechanical properties of the samples worsened on increasing the level of pc-ABS and after each reprocessing op…
An Innovative Treatment Based on Sodium Citrate for Improving the Mechanical Performances of Flax Fiber Reinforced Composites
2021
The goal of this paper is to evaluate the effectiveness of a cost-effective and eco-friendly treatment based on the use of sodium citrate (Na3C6H5O7) on the mechanical properties of flax fiber reinforced composites. To this scope, flax fibers were soaked in mildly alkaline solutions of the sodium salt at different weight concentration (i.e., 5%, 10% and 20%) for 120 h at 25 °C. The modifications on fibers surface induced by the proposed treatment were evaluated through Fourier transform infrared analysis (FTIR), whereas scanning electron microscope (SEM) and helium pycnometer were used to obtain useful information about composites morphology. The effect of the concentration of the treating …
Salt-fog spray aging of jute-basalt reinforced hybrid structures. Flexural and low velocity impact response
2017
Abstract In this work, a study on the aging resistance of jute and jute-basalt interply hybrid laminates exposed to salt-fog is presented with the aim to investigate the possibility to enhance the durability of natural fiber reinforced composites for marine application by a ply-substitution approach. In particular, jute and basalt/jute reinforced composite plates were manufactured by vacuum assisted resin infusion in two different staking sequences (i.e., intercalated and sandwich-like basalt-jute) and aged under salt fog conditions. The effects of the accelerated aging at increasing times on the mechanical response of laminates were assessed in both quasi static (three point bending) and d…
Nanocarbons in electrospun polymeric nanomats for tissue engineering: A review
2017
Electrospinning is a versatile process technology, exploited for the production of fibers with varying diameters, ranging from nano- to micro-scale, particularly useful for a wide range of applications. Among these, tissue engineering is particularly relevant to this technology since electrospun fibers offer topological structure features similar to the native extracellular matrix, thus providing an excellent environment for the growth of cells and tissues. Recently, nanocarbons have been emerging as promising fillers for biopolymeric nanofibrous scaffolds. In fact, they offer interesting physicochemical properties due to their small size, large surface area, high electrical conductivity an…