Search results for " metallurgy"
showing 10 items of 97 documents
Effect of the mineralogical composition on the elastoplastic hydromechanical response of Opalinus Clay shale
2021
Abstract Opalinus Clay is the shale currently under investigation as the host formation for geological radioactive waste disposal in Switzerland. Its hydromechanical response has been widely studied, and the experimental results show a range of values whose dispersion needs to be clarified. This work aims to explain the dispersion in the literature results by correlating the hydro-mechanical response to the mineralogical variability of the tested specimens . Based on published microstructural studies, the Opalinus Clay shale is herein schematised as a sequence of two kinds of layers: the shaly (high in clay-mineral content) and the sandy (low in clay-mineral content) layers. The mineralogic…
Evaluating pulp stiffness from fibre bundles by ultrasound
2012
A non-destructive ultrasonic tester was developed to measure the stiffness of pulp bundles. The mechanical properties of pulp are important when estimating the behaviour of paper under stress. Currently available pulp tests are tedious and alter the fibres structurally and mechanically. The developed tester employs (933 ± 15) kHz tweezer-like ultrasonic transducers and time-of-flight measurement through (9.0 ± 2.5) mm long and (0.8 ± 0.1) mm thick fibre bundles kept at (19.1 ± 0.4) °C and (62 ± 1)% RH. We determined the stiffness of soft wood pulps produced by three kraft pulping modifications: standard kraft pulp, (5.2 ± 0.4) GPa, prehydrolysis kraft pulp, (4.3 ± 0.4) GPa, and alkali extra…
A new approach to the synthesis of intermetallic compounds: mild synthesis of submicrometric CoxMy (M = Mo, W; x∶y = 3∶1 and 7∶6) particles by direct…
2002
A simple processing route to cobalt–molybdenum and cobalt–tungsten intermetallics (CoxMy, where M = Mo and W, and x∶y = 3∶1 and 7∶6) has been developed, on the basis of the use of precursors resulting from freeze-drying of aqueous solutions of the appropriate common metal salts. The influence of the preparative variables on the outcomes of this procedure is examined. These compounds are prepared as single phases by thermal reduction of amorphous freeze-dried powders under a hydrogen–argon atmosphere (8% H2), followed by slow cooling of the samples. The materials have been characterised by X-ray powder diffraction, metal analysis, scanning electron microscopy and thermogravimetry under an ox…
Twitter sentiment as a weak signal in venture capital financing
2021
Abstract How do venture capitalists (VCs) incorporate weak and strong signals in the valuation of technology-based startups? Based on a sociocognitive perspective of signaling theory, we introduce Twitter sentiment as a novel and weak signal, which we juxtapose with patents as a traditional, strong signal. While we find a positive association between both signals and VCs' venture valuations, our results reveal that Twitter sentiment does not correlate with actual long-term investment success, whereas patents do. Additionally, we identify and test novelty and experience characteristics (i.e., startup age and VC firm experience) as boundary conditions for our proposed signal-valuation relatio…
L'évolution des premières métallurgies extractives du cuivre
2003
International audience; L'histoire de la métallurgie extractive débute avec le cuivre. Malgré la rareté, des témoignages archéologiques, l'étude des sites d'extraction et notamment des déchets permet depuis peu de caractériser, au moins partiellement, les premiers procédés. Ainsi, on arrive aujourd'hui à documenter ce qui fut une véritable révolution au tout début de cette métallurgie, quand, d'une activité à faible production durant le Chalcolithique et le début de l'âge du Bronze, on passe progressivement à une véritable production de masse vers le milieu et la fin de l'âge du Bronze. Les premiers procédés sont non scorifiants, ils séparent mal le stérile du métal, et conduisent à des per…
Cinq millénaires de métallurgie en montagne basque. Les apports d'une démarche intégrée alliant palynologie et géochimie isotopique du plomb
2001
Five thousand years of metallurgy in the basque mountains : the contributions of an integrated process mixing palynology and the isotopic chemistry of lead. An interdisciplinary research combining palyno- logy and lead isotopic geochemistry was performed in a peat bog of the Basque Country, in an area recognized as being an old metallurgical centre. These various analyses make it possible to reconstitute mining and metallurgical activities and to appreciate the impact on forest during last five millennia. Several phases are attested between late Neolithic and modern times (Middle Bronze age, Late Bronze age, Antiquity and finally modern time). Most of these phases are clearly related to for…
Development of Removable Visual Impact Indicator or Polymer Composite Materials
2021
The prototype of removable visual impact indicator for thermoset polymer composite materials is developed, and its characteristics are experimentally determined. The indicator is a fabric tape glued by epoxy to the surface of the polymer composite. The tape is impregnated with a composition that provides a visual response at the place of an impact on the composite surface. Ball-drop tests demonstrated the increase of the magnitude of the visual response with the impact energy at different substrate hardnesses. The shelf-life and mode of the tape storage until commissioning are determined. Peel tests showed the ability to remove a used indicator without damaging the surface of the composite.
Open Cell Al-Si Foams by a Sintering and Dissolution Process
2014
Open cell foams from AlSi12 alloy were successfully fabricated by the Sintering and Dissolution Process, using NaCl as space holder (60 %). The size of the aluminum alloy powder is less than 45 μm, while the space holder powder size is 315-500 μm, 630-800 μm and 800-1250 μm respectively. The appropriate quantities of alloy powder and salt were mixed and cold pressed at 250 MPa. The sintering process was done at 500 °C and 545 °C, in vacuum (10-5 torr) for 10, 20 and 30 minutes respectively. The space holder was eliminated by holding the sintered samples in running hot water (70 °C). After the salt was dissolved, the samples were dried and the mass loss was analyzed. Keywords: Aluminum foam…
Thermal Analysis, Mechanical and Rheological Behaviour of Melt Manufactured Polyethylene/Liquid Crystal Polymer Blends
2011
Modification of properties of conventional thermoplastics with thermotropic liquid crystal polymers, from one hand, allows decrease their viscosities, substantially facilitating processing conditions, and, from another hand, allows increase their exploitation properties. Orientation of the labile structure of liquid crystal polymer in extrusion or injection moulding causes specific reinforcement (so-called self-reinforcement) to occur in the blends containing liquid crystal polymer. Up to now the effect of self-reinforcement is mostly investigated in the blends, containing considerable amount of liquid crystal polymer. In this research the effect of minor amounts of liquid crystalline co-po…
A data-driven surrogate-assisted evolutionary algorithm applied to a many-objective blast furnace optimization problem
2017
A new data-driven reference vector-guided evolutionary algorithm has been successfully implemented to construct surrogate models for various objectives pertinent to an industrial blast furnace. A total of eight objectives have been modeled using the operational data of the furnace using 12 process variables identified through a principal component analysis and optimized simultaneously. The capability of this algorithm to handle a large number of objectives, which has been lacking earlier, results in a more efficient setting of the operational parameters of the furnace, leading to a precisely optimized hot metal production process. peerReviewed