Search results for " motore"
showing 10 items of 87 documents
Hygrothermal ageing of reprocessed polylactide
2012
[EN] The influence of an accelerated hygrothermal ageing simulation test on a commercial PLA and its three subsequent mechanically-reprocessed materials was studied. The analysis was focused on the water diffusion kinetics and the physico-chemical changes induced by the hygrothermal degradation. Water diffusion proceeded faster than chain relaxation processes, as defined by a Case II absorption model. It was proved that the water diffusion rate decreased with subsequent reprocessing cycles and increased with higher hygrothermal ageing temperatures. Hydrolytic chain scission provoked significant molar mass decays and consequent general losses of thermal and mechanical performance. The rearra…
Effective antimicrobial materials based on low-density polyethylene (LDPE) with zinc oxide (ZnO) nanoparticles
2019
[EN] Effective antimicrobial polymeric nanocomposites were prepared with low density polyethylene (LDPE) and zinc oxide nanoparticles by melt compounding. These nanoparticles (~17 nm) obtained by the sol¿gel method, were used both as-synthesized and modified organically with oleic acid (Mod-ZnO). Young¿s modulus increased ~15 and 18% for LDPE/ZnO and LDPE/Mod-ZnO, respectively, compared to neat LDPE. When these composites were irradiated with white light, they showed an increase with nanoparticle incorporation, and the antimicrobial properties against E. coli were ~96¿99%. The release of the Zn cations was related to the antimicrobial properties. These nanocomposites are attractive for use …
Material valorisation of amorphous polylactide. Influence of thermo-mechanical degradation on the morphology, segmental dynamics, thermal and mechani…
2012
[EN] This paper reports the effects of multiple mechanical recycling on the structure and properties of amorphous polylactide (PLA). The influence of the thermo-mechanical degradation induced by means of five successive injection cycles was initially addressed in terms of macroscopic mechanical properties and surface modification. A deeper inspection on the structure and morphology of PLA was associated to the thermal properties and viscoelastic behaviour. Although FT-IR analysis did not show significant changes in functional groups, a remarkable reduction in molar mass was found by viscometry. PLA remained amorphous throughout the reprocessing cycles, but the occurrence of a cold-crystalli…
Monitoring molecular dynamics of bacterial cellulose composites reinforced with graphene oxide by carboxymethyl cellulose addition
2017
[EN] Broadband Dielectric Relaxation Spectroscopy was performed to study the molecular dynamics of dried Bacterial Cellulose/Carboxymethyl Cellulose-Graphene Oxide (BC/CMC-GO) composites as a function of the concentration of CMC in the culture media. At low temperature the dielectric spectra are dominated by a dipolar process labelled as a beta -relaxation, whereas electrode polarization and the contribution of dc-conductivity dominate the spectra at high temperatures and low frequency. The CMC concentration affects the morphological structure of cellulose and subsequently alters its physical properties. X-ray diffractometry measurements show that increasing the concentration of CMC promote…
Dielectric Spectroscopy of Recycled Polylactide
2014
The effects of multiple mechanical recycling on amorphous polylactide (PLA) were simulated by means of five successive injection-grinding cycles. The influence of the induced thermo-mechanical degradation on the dielectric properties of PLA was analysed. The relaxation spectra were studied in terms of the complex dielectric permittivity (ε0 and ε00) and the dielectric loss tangent, tg(d) in the frequency range from 102 to 107 Hz over the temperature interval from 0 C to 140 C. It was possible to distinguish two relaxations zones, one at low temperatures and high frequencies (b relaxation) and another at higher temperatures and lower frequencies (a relaxation). The individual relaxations wer…
Recent Progress in the Development of Composite Membranes Based on Polybenzimidazole for High Temperature Proton Exchange Membrane (PEM) Fuel Cell Ap…
2020
[EN] The rapid increasing of the population in combination with the emergence of new energy-consuming technologies has risen worldwide total energy consumption towards unprecedent values. Furthermore, fossil fuel reserves are running out very quickly and the polluting greenhouse gases emitted during their utilization need to be reduced. In this scenario, a few alternative energy sources have been proposed and, among these, proton exchange membrane (PEM) fuel cells are promising. Recently, polybenzimidazole-based polymers, featuring high chemical and thermal stability, in combination with fillers that can regulate the proton mobility, have attracted tremendous attention for their roles as PE…
Mechanical recycling of polylactide, upgrading trends and combination of valorization techniques
2016
[EN] The upcoming introduction of polylactides in the fractions of polymer waste encourages technologists to ascertain its valorization at the best quality conditions. Mechanical recycling of PLA represents one of the most cost-effective methodologies, but the recycled materials are usually directed to downgraded applications, due to the inherent thermomechanical degradation affecting its mechanical, thermal and rheological performance. In this review, the current state of mechanical recycling of PLA is reported, with special emphasis on a multi-scale comparison among different studies. Additionally, the applications of physical and chemical upgrading strategies, as well as the chances to b…
Relevant factors for the eco-design of polylactide/sisal biocomposites to control biodegradation in soil in an end-of-life scenario
2017
[EN] The eco-design considers the factors to prepare biocomposites under an end-of-life scenario. PLA/sisal biocomposites were obtained from amorphous polylactide and sisal loadings of 10, 20 and 30 wt% with and without coupling agent, and subjected to biodegradation in soil according to standard IS0846. Mass loss, differential scanning calorimetry and size-exclusion chromatography were used for monitoring biodegradation. A statistical factorial analysis based on the molar mass M-n, and crystallinity degree X-c pointed out the relevance and interaction of amount of fibre and use of coupling agent with the time of burial in soil., During the preparation of biocomposites, chain scission provo…
Polylactide-based self-reinforced composites biodegradation: Individual and combined influence of temperature, water and compost
2018
[EN] Self-reinforced polymer composites (SRCs) are proposed as a suitable alternative for composite development, based in the combination of a polymeric matrix and a polymeric fibre made of the same polymer. SRCs based in polylactide (PLA) could be fully biodegradable and their valorisation routes could presumably be assimilated to those for neat PEA. In this sense, the aim of this study was to develop new self-reinforced PLA-based composites and ascertain their biodegradability. For this purpose, PLA-based SRCs were obtained through a thermo-compression procedure and their biodegradability corroborated under standard conditions (ISO 20200). Moreover, a deep study of the effect of the diffe…
Protection of high-density polyethylene-silicon composites from ultraviolet-visible photodegradation
2017
[EN] The extent of the ultraviolet¿visible (UV¿vis) photoirradiation effect on high-density polyethylene (HDPE) and HDPE¿sili-con (Si) composites is reported in terms of the addition of Si microparticles at contents of 0.1, 1, and 5 wt %. A standard acceleratedUV-vis exposure was applied over 2750 h, corresponding to 22 months in Florida. Thermogravimetry, differential scanning calorimetry,and Fourier transform infrared spectroscopy were used as reliable techniques for monitoring the quality of the HDPE-Si composites. Theincreasing addition of Si microparticles delayed the photodegradation of the HDPE¿Si composites. Because of their strong light-scattering effects, Si microparticles blocked…