Search results for " polyethylene"
showing 10 items of 229 documents
Modified arabinoxylan-based films. Part B. Grafting of omega-3 fatty acids by oxygen plasma and electron beam irradiation.
2003
Arabinoxylans (AXs) are byproducts of the cereal milling industry. To obtain high-value products, AXs have been used as a film-forming agent. Hence, AX-based films are poor water vapor barriers. The objectives of this study were to graft omega-3 (omega3) fatty acids onto AX polymeric chains by using two new technologies: cold plasma and electron beam (EB) irradiation. Results show that the surface hydrophobicity of the modified films is higher than that of a waxy coating or a low-density polyethylene (LDPE) film. In addition, FTIR spectroscopy analysis reveals vibration bands attributed to new chemical functions. Finally, a decrease in water vapor permeability (WVP) is obtained for the film…
A quantitative electron-microscopic study of a linear polyethylene fraction crystallized at different temperatures
1981
Replica and thin-section electron microscopy was performed on a linear polyethylene fraction (Mw = 1.89 × 105, Mn = 1.79 × 10 5) which was either isothermally crystallized or quenched at difference temperatures. The results are numerically analyzed in such a manner so as to give the distribution of the total long spacing and of the crystallite and amorphous thicknesses. The quantitative information about the maximum and minimum values for these parameters at each crystallization temperature yields important clues as to possible molecular processes involved. Qualitative information regarding general morphology, molecular tilt with respect to the lamellar surface, and possible crystallographi…
A quantitative electron microscopic study of the crystallite structure of molecular weight fractions of linear polyethylene
1984
Utilizing thin-section techniques, transmission electron microscope studies were performed on a series of bulk-crystalized fractions of linear polyethylene covering the range M = 5 × 103−6 × 106. The crystallization conditions were varied from long-time isothermal to rapid quenching. Quantitative analysis could be carried out on such samples crystallized under controlled conditions. The crystallite thickness distributions and long periods are presented in terms of histograms. From these data the degree of crystallinity can be calculated and was found to compare favorably with that from other methods. The amorphous thickness increases significantly with molecular weight for all modes of crys…
Shear characterization of CaCO3-filled linear low density polyethylene
1988
Shear properties of CaCO3-filled linear low density polyethylene have been determined over a wide range of filler loading. The viscosity rises with the filler loading especially at low shear rates and a yield value appears for CaCO3-contents larger than 5%. The decrease of the die-swell ratios of the filled samples indicates a reduction of the melt elasticity.
Laboratory and in-situ tests for estimating improvements in asphalt concrete with the addition of an LDPE and EVA polymeric compound
2019
Abstract Pavement deformation is a critical issue in the design of pavement structures and the related mixture. Asphalt concretes may be very sensitive to this problem, in compliance with the viscoelastic behaviour of the adopted bitumen. To improve the material performance, many attempts have been made to introduce in the mixture other materials as “modifiers” or “additives” for increasing the permanent deformation resistance and the elastic modulus of the material. Among the different possible materials, polymers determined significant improvements in the road pavement performance. In this paper, the authors tested the adoption of a specifically engineered polymeric compound, in order to …
Liquid/Liquid Demixing in the System n-Hexane/Narrowly Distributed Linear Polyethylene
2004
Demixing conditions were measured visually for solutions of three narrowly distributed polyethylene samples (M ranging from 6.5 to 380 kg/mol) in n-hexane up to 500 K and 150 bar. This information yields the critical line for infinite molar mass; i.e., it specifies the pT area within which one is safe from phase separation irrespective of the molar mass of the polymer and of the composition of the mixture. The experimental findings are in good qualitative agreement with the predictions of the Sanchez−Lacombe theory applied without any adjustable parameters. The influences of molar masses are, however, underestimated, and the resulting critical compositions are too small. For a more quantita…
Rheological properties and morphology in LLDPE and PC based blends
1990
Abstract During an interlaboratory project on polymer blends (Technical Working Party-Polymer Blends-VAMAS), the rheological characteristics of some samples of blends of polycarbonate with linear low density polyethylene have been evaluated with the aid of a capillary rheometer. Some morphological observations on the extruded samples have also been performed through SEM and an attempt has been made to correlate the macroscopic and microscopic results.
Morphology and transport parameters of cold-rolled low-density polyethylene
1986
Abstract Sheets of low-density polyethylene were rolled at room temperature. Samples with two different degrees of rolling were obtained. The structural changes induced by the rolling treatments were investigated using scanning electron microscopy and by analyzing the transport properties. Results suggest that in the analyzed range of deformation, the rolling induces a domain structure as a consequence of a nonhomogeneous distribution of the deformation. At lower local deformation the initial morphology is still present, while at higher deformation clumps of folded chains oriented along the rolling directions are observable. The transport properties indicate that the rolling treatment reduc…
Compatibilized Polyamide 6/Polyethylene Blends Clay Nanocomposites: Effect of the Degradation and Stabilization of the Clay Modifier
2008
Abstract Blends of polyamide 6 (PA6) and high-density polyethylene (HDPE) were compatibilized using an already investigated method and a sample of Cloisite 15A, a montmorillonite modified with ammonium quaternary salts was added. The blends were prepared in a twin screw extruder and characterized from a morphological, rheological and mechanical point of view. The results indicated that, despite a good morphology achieved in the filled blends and a moderate intercalation of the clay, the mechanical properties are far from being good, especially the ultimate properties. In order to investigate the possible influence of the inhibition of the crystallization and of the degradation of the organi…
The role of organoclay and matrix type in photo-oxidation of polyolefin/clay nanocomposite films
2009
Abstract In this paper the photo-oxidation behaviour of polyolefin/clay nanocomposite films was studied; in particular, the effect of the amount of organo-modifier and the matrix polarity on the photo-oxidation was investigated. Two different organo-modified clays and compositions of LDPE/EVA blend films were used and the photo-oxidation was followed by mechanical and spectroscopic analyses. The organoclay and matrix type strongly influence the photo-oxidative behaviour of nanocomposite films. The films filled with CL15A show a faster loss of mechanical performance and higher carbonyl formation with respect to the films filled with the CL20A. Additionally, the LDPE based nanocomposite under…