Search results for " ra"
showing 10 items of 21965 documents
Numerical Procedures and their Practical Application in PV Module Analyses. Part IV: Atmospheric Transparency Parameters - Application
2020
Abstract The presented article relates to aspects of PV module testing using natural sunlight in outdoor conditions. It is a continuation of the article Part III: parameters of atmospheric transparency - determining and correlations. This article discusses the practical application of the indexes: atmosphere purity - k Tm , diffused component content - k s/o , beam clear sky index - K b - in testing various modules in outdoor conditions. Their influence on the conversion of modules made from various absorbers and various technologies is demonstrated. Their practical application in module testing in outdoor conditions is described and it - has been demonstrated that the results of the analys…
Optical properties of GaSe, characterization and simulation
2021
Abstract The study focuses on structural and optical characterizations and properties of the GaSe lamellar material in one hand and on a numerical simulation of the photovoltaic properties of the ITO/GaSe heterojunction in a second hand. A few layers of GaSe were exfoliated from bulk GaSe on PET substrate. The optical transmission was recorded at room temperature. It shows that GaSe exhibits both indirect and direct band gaps of about 1.92 and 2.2 eV respectively. A value, as high as 104 cm−1, of the absorption coefficient was obtained. The corresponding refractive index has been determined numerically according to the Sellmeier and Cauchy models. The interesting value of absorption shows o…
Investigation and reduction of losses on inverter-fed induction motors
2017
An electric motor is more effective and flexible when supplied by a frequency converter. The frequency converter not only produces the fundamental voltage but also a set of higher harmonics which cause additional losses in the motor. Losses in the frequency converter are normally neglected in the drive dimensioning due to insufficient data available from manufacturers. Motor's losses can be reduced by increasing the switching frequency of frequency converters. An increase of the switching frequency may result in higher losses in the frequency converter. This work investigates analytically and experimentally the dependence of the losses of modern motor and frequency converter on a switching …
Inhomogeneous electron distribution in InN nanowires: Influence on the optical properties
2012
In this work, we study theoretically and experimentally the influence of the surface electron accumulation on the optical properties of InN nanowires. For this purpose, the photoluminescence and photoluminescence excitation spectra have been measured for a set of self-assembled InN NWs grown under different conditions. The photoluminescence excitation experimental lineshapes have been reproduced by a self-consistent calculation of the absorption in a cylindrical InN nanowires. With the self-consistent model we can explore how the optical absorption depends on nanowires radius and doping concentration. Our model solves the Schrodinger equation for a cylindrical nanowire of infinite length, a…
Luminescence of divalent lanthanide doped BaBrI single crystal under synchrotron radiation excitations
2020
Abstract Luminescence excitation spectra of BaBrI single crystals doped by divalent lanthanide ions are studied using synchrotron radiation excitations from the MAX IV 1.5 GeV storage ring. The energy of the edge and the formation of core cation exciton as well as the energy threshold of the multiplications of electronic excitations is found. It was clearly established the energy transfer from intrinsic luminescence centers to Sm2+ and Eu2+ ions.
Temperature Coefficients of Crystal Defects in Multicrystalline Silicon Wafers
2020
This article investigates the influence of crystallographic defects on the temperature sensitivity of multicrystalline silicon wafers. The thermal characteristics of the implied open-circuit voltage is assessed since it determines most of the total temperature sensitivity of the material. Spatially resolved temperature-dependent analysis is performed on wafers from various brick positions; intragrain regions, grain boundaries, and dislocation clusters are examined. The crystal regions are studied before and after subjecting the wafers to phosphorus gettering, aiming to alter the metallic impurity concentration in various regions across the wafers. Most intragrain regions and grain boundarie…
Isothermal relaxation of discommensurations in K2ZnCl4
1994
At the incommensurate-ferroelectric transition temperature T c of K 2 ZnCl 4 , the dielectric susceptibility contains an anomalous contribution both above and below T c . Previous quasi-static dielectric measurements and hysteresis loops demonstrated that this anomalous part arises from the peculiar dynamics of discommensurations. We have used isothermal dielectric measurements to get some insight into the long time dynamics of these discommensurations. We have found that the characteristic relaxation times τ are of the order of 10 4 s in the incommensurate and in the ferroelectric phase. Even more unusual is a non-monotonous relaxation which is observed in a restricted temperature range ab…
EBSD, XRD and SRS characterization of a casting Al-7wt%Si alloy processed by equal channel angular extrusion: Dislocation density evaluation
2019
Abstract Aluminum‑silicon (Al Si) alloys of high silicon contents are composite materials; they are used whenever high casting properties are required. They are slightly ductile below 8wt%Si. An increase in ductility can be obtained by refining Si-crystals in elaboration or by a further hot working. In the present work, an Al-7wt%Si alloy was processed by Equal Channel Angular Extrusion (ECAE) at temperatures 20 °C and 160 °C up to three passes. The die was formed by two cylindrical channels with characteristic angles Φ = 110° and Ψ = 0. EBSD, X ray diffraction (XRD) and Strain Rate Sensitivity (SRS) were used to characterize the microstructure and the mechanical properties. High levels of …
High temperature oxidation of Mg2(Si-Sn)
2016
Abstract High temperature oxidation of Mg 2 Si 1- x Sn x alloys ( x = 0.1 ⿿ 0.6) has been investigated. The oxidation rate was slow for temperatures below 430 °C. In the temperature range between 430⿿500 °C all the alloys exhibited breakaway oxidation. The onset temperature of the breakaway region in general decreased with increasing level of Sn in the alloy. The breakaway behavior is explained by a combination of the formation of a non-protective MgO layer and the formation of Sn-rich liquid at the interface between the oxide and Mg depleted Mg 2 Sn.
Operating a cesium sputter source in a pulsed mode
2020
A scheme is presented for pulsing of a cesium sputter negative ion source by periodically switching on and off the high voltage driving the sputtering process. We demonstrate how the pulsed ion beam can be used in combination with a pulsed laser (6 ns pulse length) that has a 10 Hz repetition rate to study the photodetachment process, where a negative ion is neutralized due to the absorption of a photon. In such experiments, where the ion beam is used only for a small fraction of the time, we show that the pulsed mode operation can increase the lifetime of a cathode by two orders of magnitude as compared with DC operation. We also investigate how the peak ion current compares with the ion c…