Search results for " social sciences"

Soft Innovation Resources: Enabler for reversal in GDP Growth in the Digital Economy

2018

While Finland and Singapore have been maintaining world digital leaders position, they demonstrate interlaced contrast: high welfare with low GDP growth in Finland and higher GDP growth with lower welfare in Singapore. This provokes an uncaptured GDP postulate that Finnish wellbeing has developed more than one might conclude by GDP. However, a recent reversal in the GDP growth trend suggests the possibility that uncaptured GDP contributes to remove structural impediments in GDP growth.This paper demonstrates this hypothesis. An empirical analysis elucidating the inside the national accountings and institutional systems revealed that soft innovation resources have substituted for service cap…

District heating networks: enhancement of the efficiency

2019

International audience; During the decades the district heating's (DH) advantages (more cost-efficient heat generation and reduced air pollution) overcompensated the additional costs of transmission and distribution of the centrally produced thermal energy to consumers. Rapid increase in the efficiency of low-power heaters, development of separated low heat density areas in cities reduce the competitiveness of the large centralized DH systems in comparison with the distributed cluster-size networks and even local heating. Reduction of transmission costs, enhancement of the network efficiency by optimization of the design of the DH networks become a critical issue. The methodology for determ…

Lessons Learned from the Design and Development of Vehicle Simulators

2018

Vehicle simulators are crucial tools used in a variety of areas, such as aviation, driving, or maritime transportation. International standards require the use of motion-based vehicle simulators in training scenarios. However, the huge variety of applications and requirements makes it difficult for end users to find a motion-based commercial solution that fulfils their needs. On the other hand, commercial solutions are usually expensive as they involve specific hardware and software. Although some ad-hoc solutions have been reported, a generalized design strategy is needed. In this article, the authors emphasize the need for finding a development methodology for these important tools and th…

The tougher the environment, the harder the adaptation? A psychological point of view in extreme situations

2021

IF: 2.8 (Q1); International audience; Grounded within a multidimensional and multilevel approach, the aim of this study was to investigate the time course of Psychological Adaptation Process (PAP) dimensions (social, emotional, occupational, and physical) during one-year polar winter-overs in Subantarctic and Antarctic stations. The effects of perceived control (PC) at the start of polar winter on the dynamics of the PAP dimensions were also examined. The present findings clarify some changes in PAP in extreme environments: (a) The dimensions of psychological adaptation evolved differently as a function of environmental conditions; and (b) PC influenced the trajectories of PAP dimensions. T…

How can we do our best, in manufacturing processes?

2018

Orchestrated learning: creating a company-specific production system (XPS)

2021

Purpose Companies create company-specific production systems (XPS) by tailoring generic concepts to fit their unique situation. However, little is known about how an XPS is created. This paper aims to provide insights into the creation of an XPS. Design/methodology/approach A retrospective case study was conducted in a Norwegian multinational company over the period 1991–2006, using archival data and interviews. Findings The development of the XPS did not start with a master plan. Instead, dispersed existing initiatives were built upon, along with an external search for novel ideas. Widespread experimentation took place, only later to be combined into a coherent approach. Once established,…

Traffic data acquirement by unmanned aerial vehicle

2017

This paper presents a methodology aimed to acquire traffic flow data through the employment of unmanned aerial vehicles (UAVs). The study is focused on the determination of driving behavior parameters of road users and on the reconstruction of traffic flow Origin/Destination matrix. The methodology integrates UAV flights with video image processing technique, and the capability of geographic information systems, to represent spatiotemporal phenomena. In particular, analyzing different intersections, the attention of the authors is focused on users’ gap acceptance in a naturalistic drivers’ behavior condition (drivers are not influenced by the presence of instruments and operators on the roa…

Harsanyi Power Solutions for Cooperative Games on Voting Structures

2019

International audience; This paper deals with Harsanyi power solutions for cooperative games in which partial cooperation is based on specific union stable systems given by the winning coalitions derived from a voting game. This framework allows for analyzing new and real situations in which there exists a feedback between the economic influence of each coalition of agents and its political power. We provide an axiomatic characterization of the Harsanyi power solutions on the subclass of union stable systems arisen from the winning coalitions from a voting game when the influence is determined by a power index. In particular, we establish comparable axiomatizations, in this context, when co…

Intelligent virtual manufacturing cell formation in cloud-based design and manufacturing

2018

Abstract Cloud-based design and manufacturing (CBDM) can presumably stimulate greater intelligence in cloud-based models. This paper assumes that cloud-based design for cellular manufacturing can be referred to as a multiscale, uncertain, and dynamic service-oriented network where a set of CAD parts, modelled by set of features, can be manufactured in intelligent virtual manufacturing cells under certain constraints. Using the concepts of the holon and the attractor, integrating the uncertainty in the modelling of part design and part–manufacturing network, an approach to address intelligent virtual manufacturing cell formation in CBDM is proposed. The powerful role of the CAD features is e…

Haptic and Visual Feedback Assistance for Dual-Arm Robot Teleoperation in Surface Conditioning Tasks

2020

Contact driven tasks, such as surface conditioning operations (wiping, polishing, sanding, etc.), are difficult to program in advance to be performed autonomously by a robotic system, specially when the objects involved are moving. In many applications, human-robot physical interaction can be used for the teaching, specially in learning from demonstrations frameworks, but this solution is not always available. Robot teleoperation is very useful when user and robot cannot share the same workspace due to hazardous environments, inaccessible locations, or because of ergonomic issues. In this sense, this article introduces a novel dual-arm teleoperation architecture with haptic and visual feedb…