Search results for " steel"
showing 10 items of 244 documents
Experimental Investigation on the Compressive Behaviour of Clay Brick Masonry Columns Confined by BFRP or Steel Wires
2016
This paper presents the results of an experimental research aiming to investigate on the compressive behavior of full size clay brick masonry columns reinforced with Basalt Fiber Reinforced Cementitious Matrix (BFRCM) or with steel wires collaring. Uniaxial compressive tests were performed on eight retrofitted columns and four control specimens. Two masonry strength were considered by varying the mortar grade. Results are presented and discussed in terms of axial stress-strain relationships, failure modes and crack patterns of the specimens tested up to failure. For the limit of investigated variables, comparisons with unreinforced specimens show the ability of these alternative techniques …
Stiffness and strength of composite truss beam to R.C. column connection in MRFs
2015
Abstract The results of experimental and numerical investigations on the cyclic behavior of composite truss beam to reinforced concrete column connection of moment resisting frames are reported. The beams are constituted by a steel truss and end zone added rebar embedded within a concrete block cast in place, so that, after curing, the steel truss and the added rebar work together with the concrete matrix as reinforcement of the composite beam. Particularly, three specimens of two-span continuous beams were tested under monotonic and cyclic actions as three point bending test. With the goal to investigate about the behavior of the end zone of the beam integrated into a moment resisting fram…
BiZact tonsilektomijas un konvencionālās tonsilektomijas metožu salīdzinājums
2022
Paskaidrojošā informācija: Tonsilektomija ir viena no visbiežāk veiktajām ķirurģiskajām operācijām cilvēces vēsturē. Tonsilektomija tehnoloģijas un procedūras gadu gaitā ir attīstījušās, lai uzlabotu pacientu aprūpi saistībā ar intraoperācijas un pēcoperācijas riskiem. Mērķis: Šī pētījuma mērķis ir salīdzināt BiZact tonsilektomijas metodi ar tradicionālo «aukstās pieejas» tērauda tonsilektomijas metodi attiecībā uz ķirurģiskajiem rezultātiem. Nolūks: Klasiskā «aukstās pieejas» tērauda tonsilektomijas metode ir viena no visbiežāk izmantotajām metodēm, un tā ir balstīta uz tonsilektomijas instrumentiem, jo ar tiem ir viegli strādāt, tiem nav nepieciešama elektrība (un līdz ar to tie ir vienkā…
Reliability of numerical models for simulating galvanic corrosion processes
2012
International audience; Maturity of numerical simulation represents an important issue in the development of predictive models of galvanic corrosion. As widely used in electrochemical engineering, a coupled electrochemical-transport-reaction (CETR) model is recommended to simulate the current distribution above a galvanic corrosion cell made of the cut-edge of a galvanized steel sheet. Nevertheless, simulating current density distributions obtained experimentally by scanning vibrating electrode technique (SVET) above such a galvanic cell appears to be more accurate using an electrostatic model considering a homogeneous conductivity. In this case, the absence of concentration gradients next …
Galvanic deposition and characterization of brushite/hydroxyapatite coatings on 316L stainless steel
2016
In this work, brushite and brushite/hydroxyapatite (BS, CaHPO4·H2O; HA, Ca10(PO4)6(OH)2) coatings were deposited on 316L stainless steel (316LSS) from a solution containing Ca(NO3)2·4H2O and NH4H2PO4 by a displacement reaction based on a galvanic contact, where zinc acts as sacrificial anode. Driving force for the cementation reaction arises from the difference in the electrochemical standard potentials of two different metallic materials (316LSS and Zn) immersed in an electrolyte, so forming a galvanic contact leading to the deposition of BS/HA on nobler metal. We found that temperature and deposition time affect coating features (morphology, structure, and composition). Deposits were char…
In-situ radiotracer studies of sorption processes in solutions containing (bi)sulfite ions—II. Low carbon steel
1997
Abstract In this paper, time, potential and pH dependence of SO42− and HSO3− accumulations measured by an in-situ radiotracer method on surface oxide layers of low carbon steel are presented and discussed. This work is a continuation of a research program[1–5] and deals with the characterization of the sorption behaviour of low carbon steel in solutions containing sulfate and bisulfite ions (as a possible model of acid rain). From the experimental results it can be stated that 1. (i) the presence of bisulfite ions in the solution phase accelerates the corrosion of low carbon steel; 2. (ii) at E > 0.40 V the electrooxidation of HSO3− ions presumably proceeds to yield a steel surface covered …
Electronic properties and corrosion resistance of passive films on austenitic and duplex stainless steels
2018
Abstract Passive films were grown at constant potential in acidic (pH∼2) and alkaline (pH∼13) solutions on chromium, AISI 304L, AISI 316L and Duplex stainless steels. Passive films on chromium grow following a high field mechanism considering the presence of dissolution phenomena. According to the photoelectrochemical characterization, passive films on Cr have a bandgap of 3.4 eV when formed in acidic solution, and of 2.4 eV when formed in alkaline solution due to the formation of Cr(OH)3. These films result to be poorly stable against anodic dissolution due to a very anodic flat band potential. Conversely, impedance and photoelectrochemical measurements proved that passive films on stainle…
Seismic Performance of Earthquake-Resilient RC Frames Made with HSTC Beams and Friction Damper Devices
2021
Seismic behavior of RC frames with hybrid steel-trussed concrete beams is affected by panel zone damage due to a large amount of longitudinal reinforcement. Here the seismic efficiency of innovative frames characterized by friction damper devices (FDDs) at beam-to-column connections is compared against traditional frame. Three configurations are investigated: FDDs alone; FDDs with column-to-foundation connections having preloaded threaded bars and disk springs; FDDs with self-centering friction devices. Non-linear analyses show that FDDs alone prevent plastic hinge formation at beam ends and beam–column joint damage. FDDs with self-centering friction devices effectively limit both peak and …
Magnetic Field and Short-Circuit Reactance Calculation of the 3-Phase Transformer with Symmetrical Amorphous Core
2006
Magnetically symmetric, 3- phase transformer has been analysed. For the two variants of the windings, the calculation results have been compared with the measured ones. Magnetic flux density components were calculated in and out of the core. The flux distribution and short-circuit reactance have been verified experimentally and a good agreement has been obtained.
Contribution to the study of physico-chemical properties of surfaces modified by last treatment : application to the enhancement of localized corrosi…
2011
Metallic materials are more and more used in severe conditions with particularly strong request for improving their behavior in aggressive environment and especially over long periods. The objective of this PhD work is to estimate the potentiality of a laser surface melting treatment on the improvement of the stainless steel 304L corrosion resistance, surface treatments by laser can be revisited on the basis of a recent change in the laser technology. In the frame of this work, a nano-pulsed laser fiber was chosen : it allows the treated surface to be melted for few microns in depth, followed by an ultra-fast solidification occuring with cooling rates up to 1011 K/s. The combination of thes…