Search results for " tank"

Static and Dynamic Performance Tests on Room Temperature Hydride Tank

2014

Calibrating storage tanks for soil erosion measurement from plots

1998

Many plots for soil loss measurements are equipped with a sequence of tanks for measuring runoff volume and sediment concentration. The stored water volume is easily determined by a water depth measurement while the sediment concentration is often measured by collecting samples of the mixed suspension. In this paper, using the Π-theorem of dimensional analysis, the functional relationship describing the mixing of the suspension in the tank is expressed in a dimensionless form. The recognized dimensionless groups allow the establishment, for given soil and water depth in the tank, of the relationship (calibration curve) between the actual and the measured concentration. The calibration curve…

MANUAL SAMPLING AND TANK SIZE EFFECTS ON THE CALIBRATION CURVE OF PLOT SEDIMENT STORAGE TANKS

2004

In many experimental soil erosion plots, runoff is collected and carried by a conveyance system to a sequence of storage tanks. If the soil loss is measured by collecting, after mixing, samples of the stored suspension, then a calibration curve between the actual mean concentration (C) and the measured concentration (Cm) in the storage tank occurs. The aim of this article was to evaluate experimentally the factors affecting the relationship between C and Cm. For a sandy loam soil, the replicated measurements of Cm (20 samples) for two values of the actual concentration (C = 5 and 25 g/L) showed that the variability of the measurements of Cm is low and confirmed the reliability of a calibrat…

Development of a modular room-temperature hydride storage system for vehicular applications

2016

The subject of this paper concerns the development of a vehicular hydrogen tank system, using a commercial interstitial metal hydride as storage material. The design of the tank was intended to feed a fuel cell in a light prototype vehicle, and the chosen hydride material, Hydralloy C5 by GfE, was expected to be able to absorb and desorb hydrogen in a range of pressure suitable for this purpose. A systematic analysis of the material in laboratory scale allows an extrapolation of the thermodynamic and reaction kinetics data. The following development of the modular tank was done according to the requirements of the prototype vehicle propulsion system and led to promising intermediate results…

Experimental Investigation for Local Tank Inflow Model

2014

In the present paper the effect of private roof tanks and of the float valve characteristics on apparent losses due to water meter errors was investigated via an experimental study. The tests were carried out at the Environmental Hydraulic Laboratory of the University of Enna (Italy), on a high-density polyethylene (HDPE 100 PN16) looped distribution network. The experimental results showed that network pressure plays an important role in the characterisation of the floating ball valve emitter law, but the tank operating condition is the most relevant aspect to be considered mainly for water meter error evaluation. (C) 2014 The Authors. Published by Elsevier Ltd.

Mass transfer and hydrodynamic characteristics of unbaffled stirred bio-reactors: Influence of impeller design

2014

Abstract Unbaffled stirred tanks are increasingly recognized as a viable alternative to common baffled tanks for a range of processes where the presence of baffles is undesirable for some reason. For instance, in the case of shear sensitive cell cultivation (e.g. human cells), unbaffled tanks have been recently found to be able to provide sufficient mass transfer through the free surface vortex. As a consequence the need for bubble formation and subsequent bursting, along with relevant cells damage, is conveniently avoided. In this work the influence of impeller geometry on mass transfer performance and power demand of an unbaffled stirred vessel operating both in sub-critical conditions (t…

Unbaffled, Stirred Bioreactors for Animal Cell Cultivation

2017

One of the main features of animal cell bioreactors is that the cultured cells lack a strong membrane and are therefore more prone to shear damage. It is widely accepted that animal cell damage in aerated bioreactors is mainly related to burst bubbles at the air–liquid interface. A viable alternative to sparged bioreactors, aimed at minimizing cell damage, may be represented by uncovered, unbaffled, stirred tanks, which are able to provide sufficient mass transfer through the deep free surface vortex that takes place under agitation. As a consequence the need for bubble formation and subsequent bursting accompanied by cell damage is conveniently avoided. In this chapter, mass transfer perfo…

Effect of the height-to-diameter ratio on the mass transfer and mixing performance of a biotrickling filter

2017

BACKGROUND Biotrickling filters (BTFs) are among the most widely used biological technologies for air pollution control. The pollutant removal rate in BTFs relies to a large extent on its gas–liquid mass transfer performance. Therefore, knowledge of the design parameters affecting the mass transfer and mixing performance of full-scale BTFs is of paramount importance. RESULTS This work showed that the height-to-diameter (H/D) ratio is an important parameter in the design of BTFs devoted to air pollution control. The H/D ratio significantly affected the mass transfer and mixing performance of the BTF with and without additional stirring in the holding tank. It was observed that under the same…

Particle suspension in top-covered unbaffled tanks

2010

Abstract Unbaffled stirred tanks are seldom employed in the process industry as they are considered poorer mixers than baffled vessels. However, they may be expected to provide significant advantages in a wide range of applications (e.g. crystallization, food and pharmaceutical processes, etc.), where the presence of baffles is often undesirable. In the present work solid–liquid suspension in an unbaffled stirred tank is investigated. The tank was equipped with a top-cover in order to avoid vortex formation. A novel experimental method (the “steady cone radius method”, SCRM) is proposed to determine experimentally the minimum impeller speed at which solids are completely suspended. Experime…

On vortex shape in unbaffled stirred vessels as measured by digital image analysis

2012

In this work, digital image analysis coupled with a suitable shadowgraphy-based technique is employed to investigate the shape of the free-surface vortex that forms in uncovered unbaffled tanks stirred by either a D=T/3 Lightnin A310 or a D=T/3 Rushton turbine. The technique is based on back-lighting the vessel and suitably averaging vortex images over time. Data obtained show that the two different impellers give rise to quite different vortex shapes. A novel 2-parameter model is proposed that successfully describes vortex shapes obtained with both impellers.