Search results for "0201 civil engineering"
showing 10 items of 242 documents
Experimental Investigation on the Compressive Behaviour of Clay Brick Masonry Columns Confined by BFRP or Steel Wires
2016
This paper presents the results of an experimental research aiming to investigate on the compressive behavior of full size clay brick masonry columns reinforced with Basalt Fiber Reinforced Cementitious Matrix (BFRCM) or with steel wires collaring. Uniaxial compressive tests were performed on eight retrofitted columns and four control specimens. Two masonry strength were considered by varying the mortar grade. Results are presented and discussed in terms of axial stress-strain relationships, failure modes and crack patterns of the specimens tested up to failure. For the limit of investigated variables, comparisons with unreinforced specimens show the ability of these alternative techniques …
Influence of bio-based additives on RAP clustering and asphalt binder rheology
2017
The use of high Reclaimed Asphalt Pavement (RAP) content in Hot Mix Asphalt (HMA) allows developing innovative materials for the construction and/or rehabilitation of sustainable infrastructures. The chemo-physical phenomena occurring during production of HMA containing high RAP content should be investigated and considered for the mix design optimization. In fact, when additives are used as rejuvenators of the aged bitumen, these phenomena can be affected causing significant variations in the mixture characteristics. This paper aims at studying the influence of two bio-based additives specifically on RAP clustering, phenomena which can significantly affect the performance of high-content R…
Simple equations for strength and deformability verification of tubular steel wind turbine towers
2021
Abstract Simple analytical expressions for a preliminary design of tubular steel wind turbine towers under flexure and shear are proposed. Expressions derived included local buckling effects, shear to moment interaction, ovalization of cross-section and inelastic rotation of foundation. A finite-element analysis with ABAQUS program was also conducted for examination of the ovalization effects and for the whole response of steel tube in flexure. Numerical and analytical results were compared with the experimental results of recent studies available in the literature, showing good agreement. The range of variable investigated refers to medium and large size steel wind tower with cylindrical s…
Debonding Phenomena in CFRP Strengthened Calcarenite Masonry Walls and Vaults
2009
In this paper the results of an experimental investigation on full-scale reinforced masonry elements like vaults and walls are presented. The masonry type is constituted by calcarenite ashlars and bed joint mortar and the reinforcement is constituted by Carbon Fibre Reinforced Polymer (CFRP) strips. Preliminary experimental results obtained in a previous research by the authors on the local behaviour at the interface CFRP-calcarenite are summarized. Tests with controlled displacement are carried out on out-of-plane loaded walls and cylindrical vaults loaded at a quarter of the span. Results of tests carried out before and after the application of the reinforcement made it possible to evalu…
Compressive behaviour of eccentrically loaded slender masonry columns confined by FRP
2018
Abstract Fibre Reinforced Polymer (FRP) confinement represents an effective tool for retrofitting masonry piers or columns enhancing their structural performance. This technique has been widely studied in the literature mainly with reference to short columns, while no extensive information is available on the influence of second order effects on its efficacy in case of slender members. Within this framework, the presented study concerns a simplified method able to assess the effects of FRP confinement on the compressive behaviour of slender masonry columns. A proper constitutive law of FRP confined masonry in compression is adopted for performing a sectional analysis, in which also consider…
Analytical modelling of force transmission in axially loaded RC columns with indirectly loaded jackets
2019
Abstract Concrete and steel jacketing are common strengthening techniques for reinforced concrete (RC) columns subjected to axial loads. In the most of cases the external jacket is made leaving gaps between the strengthening layer and the slabs, avoiding to carry directly a portion of the load. In this way, the external jacket induces a confinement pressure on the inner column, and its beneficial effect is due to the increase of strength and ductility. However, shear stresses develop on the interface between the column and consequently, the external jacket can be considered indirectly loaded. It sustains a portion of the axial load, which depends by the value of the axial shortening, relati…
Shear-to-Moment Interaction in Glass Beams with Open Cross Sections
2018
An experimental investigation regarding the flexural behavior of glass beams with a length of 1,200 mm and rectangular, T-shaped, or I-shaped cross sections is presented and discussed. T-shaped and I-shaped cross sections were obtained by assembling laminated glass (LG) panels of 200 mm depth and 12.76 mm thickness through an acrylic adhesive. Three specimens for each series investigated were tested in flexure, focusing on the flexural and shear response of beams through the determination of the load-deflection curves and crack patterns at rupture. The shear span to depth ratio a/d was 2.25, which is a very low value, and interaction of shear and bending moment occurred during the tests. An…
Overstrength requirements to avoid brittle shear failure in RC slender beams with stirrups
2020
Abstract In this paper, an analytical expression was derived for the prediction of shear strength of slender reinforced concrete (RC) beams with stirrups. Failure occurring in B and D regions of the beam was considered. An expression derived for the shear strength of the B region was based on a modified constant angle truss model. The analytical expression derived consisted of three terms. The first one was related to the concrete contribution expressed through the square root of cylindrical compressive strength, geometrical ratio of longitudinal bars, and depth to width ratio. The second one was relating to the shear force induced by yielding of stirrups to the inclination of the main crac…
Quality control of manufacturing and hot storage of crumb rubber modified binders
2020
The ultimate performance of crumb rubber modified (CRM) binders is linked to the accurate control of the properties during manufacturing and hot storage. However, due to their complexity, asphalt technologists find the characterisation of these materials still challenging. In this study, the adoption of a Dual Helical Ribbon (DHR), a novel mixing/measuring device for rotational viscometers, is proposed for the real-time monitoring of CRM binders during manufacturing and hot storage. According to the laboratory results, manufacturing periods of 45-60 min at 195 degrees, as well as storage temperatures not exceeding 150 degrees C, are recommended for this type of modified binders. (C) 2019 El…
Investigation on fracture of epoxy-filled composites by acoustic emission
2016
Acoustic emission (AE) technique is widely used to monitor failure processes in composite materials includ-ing development of cracks and plastic deformations within the polymer matrix, fracture and debonding of inclusions, etc. In this study, the AE technique was applied investigating failure character of epoxy polymers with different content of nanofiller – fine polyethersulfone (PES) powder. Variation of material properties of the epoxy with 0, 5%, 7.5%, 10%, and 12.5% concentration (by weight) of the PES was assessed experimentally. Correlation between the PES content and the modulus of elasticity was found negligible. The same was characteristic for the tensile strength. Whereas, such a…