Search results for "1105"
showing 10 items of 459 documents
Validation of a Shear Model for RC and Hybrid Beams with Two Different Inclinations of Transversal Reinforcement
2016
The validation of an analytical model recently proposed for evaluation of the shear capacity in Reinforced Concrete (RC) beams containing multiple inclination of transverse stirrups is presented. The model is a suitable extension of that currently proposed in Eurocode 2 for the evaluation of the shear resistance, and it is derived by means of the the variable-inclination stress-field theory based on Nielsen’s plastic approach. Experimental and numerical data available in the literature on Hybrid Steel-Trussed Concrete Beams (HSTCBs) are used for model validation and result discussion. Finally, also the comparison with a different analytical approach for the assessment of the shear resistanc…
Cyclic behavior of composite truss beam-to-RC column joints in MRFS
2016
In the present paper, the cyclic behavior of beam-to-column joints made up of Hybrid Steel Trussed Concrete Beams (HSTCBs) connected to Reinforced Concrete (RC) piers is investigated. HSTCBs are a typology of composite beam generally constituted by a steel truss with end zone added rebars embedded within a block of concrete cast in place. HSTCBs represent a structural solution for light industrialization in the civil constructions; the main advantages in their use are the higher construction speed with the minimum site labor, the possibility of covering wide spans with low depths and a final economical convenience. For these reasons, they are also increasingly adopted within seismic framed …
Experimental Investigation for Degradation Analysis of an RC Italian Viaduct and Retrofitting Design
2020
AbstractThe degradation state of RC bridge structures is one of the most important and difficult aspects to be interpreted. For these structures, structural analysis using FEM requires a reliable d...
Analytical evaluation of steel–concrete composite trussed beam shear capacity
2015
A calculation method for the prediction of the shear resistance of precast composite beams, named Hybrid Steel Trussed-Concrete Beams (HSTCBs), is herein proposed. HSTCBs are constituted by a prefabricated steel truss embedded within a concrete matrix cast in situ so that, after curing, the two materials work together in the mechanical response of the composite structural element, the steel truss behaving as reinforcement of the beam. The proposed analytical model is developed on the basis of the results of a reference experimental campaign of three-point bending tests available in the literature, carried out on specimens of HSTCB designed in order to attain a shear failure. Furthermore, th…
An experimental study on relationship between LED lamp characteristics and non image-forming
2017
The general aim of the experimental study, presented in this paper, was that to investigate the relationship between the characteristics of five different types of LED (Light Emitting Diode) lamps, which are nowadays those allowing the highest energy consumption reduction, and the humans non image-forming (NIF) reactions.
Frictional effects in structural behavior of no-end-connected steel-jacketed RC columns: Experimental results and new approaches to model numerical a…
2017
Steel jacketing of reinforced concrete (RC) columns is a common retrofitting technique used to restore bearing and deformation capacity of buildings presenting structural deficiencies. For practical reasons, steel angles are in several cases arranged leaving a gap with the end beams or slabs. Despite this disconnection, the angles are still able to support a non-negligible portion of load because of the frictional forces developed along the column-angle contact interface. In these cases, the definition of computational numerical and analytical models for the assessment of reinforced cross sections becomes more complex and must be handled with care. The actual load-carrying capacity of the a…
Methodological frontier in operational analysis for roundabouts: a review
2016
Several studies and researches have shown that modern roundabouts are safe and effective as engineering countermeasures for traffic calming, and they are now widely used worldwide. The increasing use of roundabouts and, more recently, turbo and flower roundabouts, has induced a great variety of experiences in the field of intersection design, traffic safety, and capacity modeling. As for unsignalized intersections, which represent the starting point to extend knowledge about the operational analysis to roundabouts, the general situation in capacity estimation is still characterized by the discussion between gap acceptance models and empirical regression models. However, capacity modeling mu…
Composite Building Materials: Thermal and Mechanical Performances of Samples Realized with Hay and Natural Resins
2017
Unidad de excelencia María de Maeztu MdM-2015-0552 Recent years have seen an increasing public interest in issues related to energy saving and environmental pollution reduction in the building sector. As a result, many directives have been issued, the most important being the Directive 2010/31/EU (EPBD Recast) on the energy performance of buildings, which requires that "Member States shall ensure that by 31 December 2020 all new buildings are nearly zero-energy buildings". This goal can be obtained not only by reducing energy demand for heating and cooling, but also, for example, by improving building envelope performances. In this work, a first analysis of the thermal and structural behavi…
Factors affecting the choice of construction project delivery in developing oil and gas economies
2016
ABSTRACTConstruction academics and practitioners often disagree on which set of factors should take precedence over another and the basis for their inclusion in selecting a project delivery method. This disagreement exacerbates the probability of project failure, which could be detrimental to developing economies. Despite significant cost overruns and these economies being the largest contributors towards global energy sector growth, there is limited knowledge on appropriate factors to be used for selecting project delivery methods in developing oil and gas nations. An evaluation undertaken in Trinidad reveals there are no significant differences in the mean expressed by 133 professionals i…
A Review of Building Information Modelling for Construction in Developing Countries
2016
Building Information Modelling (BIM) is wide ly seen as a catalyst for innovation and productivity in the construction industry. BIM can assist a more sustainable construction process that in turn may contribute to eradicating poverty in developing c ountries (Un ited Nation Millennium Goals). While BIM is increasingly be ing adopted in developed coun tries, implementations in the developing country context are rare. Research has establishe d how construction firms struggle from several limitations having to do with the socio - economic and technological environment found in developing countries. Examples of issues preventing BIM adoption include a shortage of IT - literate personnel as wel…