Search results for "1105"
showing 10 items of 459 documents
A new procedure to determine the rheological properties of RAP binder and corresponding bituminous blends
2017
Abstract In this paper, a new and simple approach to estimate the rheological properties of Reclaimed Asphalt Pavement (RAP) binder is proposed to overcome the limitations of the conventional extraction procedure. This method is based on Dynamic Shear Rheometer tests performed on mortars composed of RAP fine fraction and virgin binder, together with a new back-calculation solution. The properties of the bituminous blends of virgin and RAP binders are obtained with a modified Nielsen model. The Voigt model is then successfully used to estimate complex modulus and phase angle of the RAP binder from the properties of the back-calculated binder blend. This procedure would prevent the need of RA…
Mix design and mechanical performance of geopolymer binder for sustainable construction and building materials
2017
Sustainability in construction is a major concern worldwide, due to the huge volume of materials and energy consumed by this sector. Associated supplementing industries (e.g. Portland cement production) constitute a significant source of CO2 emissions and global warming. Valorisation and reuse of industrial wastes and by-products make geopolymers a solid and sustainable via to be followed as a valid alternative to Portland cement. In this work the mix design of a green fly ash-based geopolymer is evaluated as an environmentally friendly construction material. In the pursuit of sustainability, wastes from a regional kraft pulp industry are exploited for the material processing. Furthermore, …
Thermo-rheological analysis of WMA-additive modified binders
2020
AbstractThermo-rheological characteristics of unmodified and modified bitumen have significant impacts on the mechanical response of asphalt. This study investigates the impacts of an organic and a chemical Warm Mix Asphalt additive on bitumen thermo-rheological and mechanical characteristics. Modified binders with different concentrations of each additive were studied and analysed comparatively to a 40/60 penetration grade bitumen. Frequency sweep tests were performed at different ageing levels to characterise the Linear Viscoelastic properties. The multiple stress creep and recovery, linear amplitude sweep (LAS) and low temperature creep stiffness tests, together with the Glover–Rowe (G–R…
A shear test for structural adhesives used in the consolidation of old timber
2001
A test method was developed specifically for structural adhesives used in thick joints. It is based on compressive shear loading of glued joints (GJ) and solid wood (SW) specimens, before and after a suitable accelerated ageing cycle. The evaluation of results is based on the ratios of wet strength to dry strength and on the comparison of GJ specimens to SW specimens which are prepared from the same batch of wood, in order to minimise the influence of the variability in wood characteristics. On a group of 10 epoxy-based adhesives, specifically marketed for the consolidation of old timber structures, the method has proved to be effective to differentiate the performances of each product. Amo…
Compressive behavior of FRP externally wrapped R.C. column with buckling effects of longitudinal bars
2018
Abstract In this paper, a calculation model to simulate the compressive behavior of R.C. columns with square cross-sections externally wrapped with FRP, including buckling effects of the longitudinal bars and reduction of the confinement pressure induced by the buckled compressed bars, is presented and discussed. The model distinguishes the cases of corner and side bars, calculating the different critical lengths and the critical loads. The Teng et al. (2009) model was adopted to predict the compressive behavior of FRP-confined concrete, and the Dhakal and Maekawa (2002) model was taken into account to predict the compressive behavior of longitudinal bars. The critical length and critical s…
Moment-axial force domain of corroded R.C. columns
2016
In the present paper, a simple model to determine the moment-axial force domain of the cross-section of reinforced concrete (R.C.) columns subjected to corrosion process is presented. The model considers members with square and rectangular cross-sections and it accounts for—cover spalling; buckling of longitudinal reinforcing bars; loss of bond of bar in tension; reduction of confinement pressures (due to the reduction of the area of stirrups and cracking of concrete induced by rust formation). The analytical expressions for prediction of the area reduction of steel, bond strength and critical load of longitudinal bars utilized were verified against experimental data available in the litera…
Linear viscoelastic properties of high reclaimed asphalt content mixes with biobinders
2017
The use of high Reclaimed Asphalt (RA) content mixtures together with binders produced from renewable resources (biobinders) is one of the current challenges in pavement engineering research. On the one hand, RA has been used for decades, but there are still some concerns about its performance, especially when high contents are used (>30%). On the other hand, biobinders are relatively new materials, which have to be deeply characterised and studied in order to develop good practices for their use. In this paper, linear viscoelastic properties of biobinders and bio-mixtures manufactured with high RA content and biobinders are analysed and discussed. High-modulus mixtures with 50% RA were…
Influence of axial force and corrosion on failure of prestressed concrete structures considering M-V interaction
2021
Abstract Existing prestressed concrete structures suffer from degradation of prestressing for two main reasons: a defect of the sheath infills (cement grout) of bonded tendons, and corrosion of steel strands. These two causes, often concomitant, lead to a reduction over time of the effectiveness of initial prestressing, in addition to the ordinary tension losses due to concrete shrinkage and creep, and to steel relaxation. In many cases a consequence of bad grouting in bonded tendons is that the structure shows an intermediate behavior between that of external prestressing and that of internal bonded prestressing. This, added to damage to wires due to corrosion, makes it essential for the d…
Improvements in aggregate-paste interface by the hydration of steelmaking waste in concretes and mortars
2019
[EN] The objective of the experimental work is to study the mechanical properties in self-compacting concretes (SCC) in which part of the limestone aggregate has been replaced by granulated blast furnace slag (GBFS) in different percentages ranging from 0% to 60%. The results show that at early ages the SCC with the largest content in slag tend to have lower compressive strengths due to the poor compacting of the aggregates, although in the long-term their strength increases due to the reactivity of the slag. In fact, at the age of 365 days, the mortars made with the substitution of 50% of cement by ground GBFS reach compressive strength similar to that of the mortar made with 100% of cemen…
Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers
2020
Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…