Search results for "2010"
showing 10 items of 449 documents
Moment-axial force domain of corroded R.C. columns
2016
In the present paper, a simple model to determine the moment-axial force domain of the cross-section of reinforced concrete (R.C.) columns subjected to corrosion process is presented. The model considers members with square and rectangular cross-sections and it accounts for—cover spalling; buckling of longitudinal reinforcing bars; loss of bond of bar in tension; reduction of confinement pressures (due to the reduction of the area of stirrups and cracking of concrete induced by rust formation). The analytical expressions for prediction of the area reduction of steel, bond strength and critical load of longitudinal bars utilized were verified against experimental data available in the litera…
A multi-technique characterisation of cronstedtite synthetized by iron-clay interaction in a step by step cooling procedure
2013
International audience; The cooling of steel containers in radioactive-waste storage was simulated in a step-by-step experiment from 90 to 40 degrees C. Among newly formed clay minerals observed in run products, cronstedtite was identified by a number of analytical techniques (powder X-ray diffraction, transmission electron microscopy, and scanning electron microscopy). Cronstedtite has not previously been recognized to be so abundant and so well crystallized in an iron-clay interaction experiment. The supersaturation of experimental solutions with respect to cronstedtite was due to the availability of Fe and Si in solution, as a result of the dissolution of iron metal powder, quartz, and m…
Influence of axial force and corrosion on failure of prestressed concrete structures considering M-V interaction
2021
Abstract Existing prestressed concrete structures suffer from degradation of prestressing for two main reasons: a defect of the sheath infills (cement grout) of bonded tendons, and corrosion of steel strands. These two causes, often concomitant, lead to a reduction over time of the effectiveness of initial prestressing, in addition to the ordinary tension losses due to concrete shrinkage and creep, and to steel relaxation. In many cases a consequence of bad grouting in bonded tendons is that the structure shows an intermediate behavior between that of external prestressing and that of internal bonded prestressing. This, added to damage to wires due to corrosion, makes it essential for the d…
Pd supported on magnetic carbon coated halloysite as hydrogenation catalyst: Study of the contribution of carbon layer and magnetization to the catal…
2019
Abstract In this article, a magnetic carbon-coated halloysite nanoclay (Hal) was prepared through introduction of hydrothermally carbonized glucose (Glu) on Hal followed by the immobilization of magnetic nanoparticles (MNPs) and incorporation of resorcinol-formaldehyde polymeric shell (RF) and carbonization. The resulting composite was then successfully applied for the immobilization of Pd nanoparticles to afford Pd@Hal@Glu-Fe-C that could efficiently promote hydrogenation of nitroarenes in the aqueous media at low temperature. The catalyst exhibited high selectivity toward nitro group. Moreover, it was highly recyclable with low MNPs and Pd leaching. To elucidate the contribution of each c…
Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers
2020
Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…
Masonry columns confined with fabric reinforced cementitious matrix (FRCM) systems: A round robin test
2021
Abstract The conservation and the preservation of existing masonry buildings, most of them recognized as cultural heritage, require retrofitting techniques that should reduce the invasiveness and assure reversibility and compatibility with the substrate. In this perspective, the strengthening system should be able to improve the bearing capacity of the structural member and, at the same time, to assure mechanical and material compatibility. The use of Fabric Reinforced Cementitious Matrix (FRCM) composites is now recognized to be suitable for these purposes. Indeed, the inorganic matrix has comparable properties with respect to the existing historical mortars while the fabric has relevant t…
Stainless steel grids for confinement of clay brick masonry columns
2016
This work presents the results of an experimental investigation on the behavior of 21 solid clay brick columns internally strengthened by stainless steel grids placed in the horizontal joints of mortar. This reinforcing technique can be applied as a constructive technique for new construction or as a retrofitting technique for existing structures (old structures to be reconstructed by original constructive method and internal reinforcement). Monotonic compressive loading tests were carried out under concentric and eccentric load. The effects of different numbers of steel grids and eccentricity of the external load were examined. Also, a detailed characterization of the constituent materials…
Computational Study of Failure of Hybrid Steel Trussed Concrete Beams
2017
This study investigates the failure behavior of hybrid steel trussed concrete beams (HSTCBs) under three-point bending through a series of finite-element (FE) simulations. The FE model employs well-established constitutive relations of concrete and steel with a simplified contact condition between the concrete and steel truss. The numerical model is compared with existing experimental data as well as a FE model that uses a more sophisticated concrete-steel interfacial model. The comparison shows that the present model is able to capture various failure mechanisms of the beam and its peak load capacity. The model is applied to investigate the behavior of a set of HSTCBs of different sizes, w…
A strategy for the finite element modeling of FRP-confined concrete columns subjected to preload
2018
Abstract Compressive behavior of columns strengthened by means of an outer elastic confinement provided e.g. by fiber-reinforced polymer (FRP) jackets has become a main topic in the field of structural retrofitting. In details, the problem of the response assessment of strengthened columns is still under study. Many analytical formulations have been proposed to describe the compressive behavior of confined concrete under both monotonic and cyclic loads. However, the effect of a stress/strain level in the columns already present prior to apply the confinement has been generally neglected until now, also because of the lack of well defined strategies of modeling. In this frame, here, (1) a FE…
Crack growth models for multiaxial fatigue in a ship’s propeller shaft
2021
Abstract A premature fatigue failure of a large intermediate propeller shaft in a shuttle tanker is discussed and analyzed. The short fatigue life consists mainly of a crack growth phase. Life predictions are carried out by crack growth modelling based on engineering fracture mechanics. The purpose of the present investigation is to identify the most likely loading modes based on the evolution of the crack propagation. A Linear Elastic Fracture Mechanics Model (LEFM) is applied with the stress intensity factor range entering the Paris law as a key parameter. Existing formulas for the geometry functions are supplemented by more detailed stress intensity factor calculations pertaining to smal…